Philips BTM2460/12 - User Manual

4 EN Overview of the main unit a • Turn the unit on or off. • Switch to standby mode or Eco standby mode. b SOURCE • Press to select a source: DISC, USB, TUNER, BT, AUDIO IN. c /PAIRING • Star t, pause, or resume play. • In Bluetooth mode, press and hold for 3 seconds to enter pairing mode. d • Stop...

7 EN 3 Get started Caution • Use of controls or adjustments or performance of procedures other than herein may result in hazardous laser exposure or other unsafe operation. Always follow the instructions in this chapter in sequence. If you contact Philips, you will be asked for the model and serial ...

8 EN Prepare the remote control Caution • Risk of product damage! When the remote control is not used for long periods, remove the batter y. To insert the remote control battery: 1 Open the batter y compar tment. 2 Inser t the supplied AAA batter y with correct polarity (+/-) as indicated. 3 Close t...

9 EN 4 Play Play from disc Note • Make sure that the disc contains playable audio content. 1 Press CD to select the DISC source. 2 Inser t a disc into the disc compar tment with the printed side facing you. » Play star ts automatically. If not, press . Play from USB Note • Make sure that the USB dev...

10 EN Program tracks You can program a maximum of 20 tracks. 1 Stop play, and then press PROG / SCAN to activate programming mode. 2 For MP3 tracks, press ALBUM/PRESET / to select an album. 3 Press / to select a track, and then press PROG / SCAN to confirm. 4 Repeat steps 2-3 to program more tracks....

11 EN 4 Play music on the connected device. » Music streams from your Bluetooth enabled device to this unit. • If you fail to search for ' Philips BTM2460 ' or cannot pair with this unit, press and hold / PAIRING for three seconds until you hear a beep sound to enter pairing mode. To disconnect the ...

13 EN 6 Adjust sound The following operations are applicable to all suppor ted media. Select a preset sound effect • Press SOUND repeatedly to select a preset sound effect. • DSC 1 (Powerful), DSC 2 (Balanced), DSC 3 (Warm), DSC 4 (Bright), DSC 5 (Clear). Adjust volume level • On the remote control,...

14 EN 7 Other features Set the alarm timer This unit can be used as an alarm clock. You can select DISC , USB , or TUNER as the alarm source. Note • Make sure that you have set the clock correctly. 1 In standby mode, press and hold SLEEP/ TIMER for three seconds. 2 Press / repeatedly to select an al...

15 EN Listen through a headphone • Plug a headphone (not supplied) into the socket.

16 EN 8 Product information Note • Product information is subject to change without prior notice. Specifications Amplifier Rated Output Power 2 x 10 W Frequency Response 63 -20KHz, +/-3dB Total Harmonic Distor tion <1%(1 KHz) Signal to Noise Ratio (A-weighted) >72dBA AUDIO IN 650mV RMS 22kohm ...

17 EN USB playability information Compatible USB devices: • USB flash memor y (USB2.0 or USB1.1) • USB flash players (USB2.0 or USB1.1) • memor y cards (requires an additional card reader to work with this unit) Supported USB formats: • USB or memor y file format: FAT12, FAT16, FAT32 (sector size: 5...

18 EN 9 Troubleshooting Warning • Never remove the casing of this unit. To keep the warranty valid, never tr y to repair the unit yourself. If you encounter problems when using this device, check the following points before requesting ser vice. If the problem remains unsolved, go to the Philips Web ...

20 EN 10 Notice Any changes or modifications made to this device that are not expressly approved by Gibson Innovations may void the user’s authority to operate the equipment. Declaration of conformity Hereby, Gibson Innovations declares that this product is in compliance with the essential requireme...