Page 3 - Contents
3 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 Contents Safety Precautions ...........................................................................................................................................4 Proper Care and Safety ..................................................................
Page 4 - Proper Care and Safety
4 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 Please read this manual before using the product. • Unit can be placed vertically (preferred) or horizontally. • To clean, use a soft, dry cloth only. Do not use water or other cleaning products as they may cause electrical failure or damage the surface o...
Page 5 - fl; Features; Introduction; Minutes; Tip; PRO WIRELESS MULTIMEDIA KIT; R E ADY
5 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 HD Flow Pro Wireless Multimedia Kit provides Full HD 1080p signal transfer, including 3D signal*, without the hassle of running cables. Create brilliant HD quality multimedia for signage, presentations, or entertainment in any location,completely un-tethe...
Page 6 - Product Specifi cations
6 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 2 x HDMI up to 1080p (60Hz)1 x Composite1 x YPbPr Component1 x HDMI up to 1080p (60Hz)1 x Composite1 x YPbPr ComponentH.264 Baseline Profile with Level 4.2HDCP compliant Wireless Connection Supporting IEEE 802.11n: OFDMRJ-45 LAN PortDirect Connection (LAN...
Page 8 - Transmitter Front; Transmitter
8 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 Transmitter Front 1 2 3 4 5 6 7 Transmitter
Page 10 - Transmitter Back
10 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 2 Transmitter Back 1 3 4 5 6 7 8
Page 12 - Receiver Front; Receiver
12 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 1 2 3 4 5 6 Receiver Front Receiver
Page 13 - IR receiving window enables remote control of components.
13 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 Receiver Front 1 . Power/Link • Blinking indicator light - System booting or establishing link between the Transmitter and the Receiver.• Rapid blinking indicator light - Software upgrading or wireless/LAN mode switching.• Solid indicator light - Link be...
Page 14 - Receiver Back
14 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 1 2 3 4 5 6 7 8 Receiver Back
Page 16 - Remote Control
16 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 1 4 3 6 7 2 5 8 1 . POWER Button - Turns the Transmitter and Receiver power ON/OFF. • ON: If the Transmitter and Receiver are powered off and the Power/Link Indicator Light is on, press the power button pointed at either unit to turn on both unit's at th...
Page 18 - Installing the Remote Control Battery; The battery slip is located on the bottom of the remote control.
18 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 Installing the Remote Control Battery The battery slip is located on the bottom of the remote control. Step 1 Push the tab, located on the left of the battery slip, to the right and pull out the slip. Battery Slip Battery Slip Tab Step 2 Place the batter...
Page 19 - Connecting Source Components To The Transmitter; or; B. Composite Media Source; Video – Connect “yellow” composite video RCA post to yellow port.; Installation and Operation
19 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 Before starting the installation, please ensure that all source components (Blu-ray player, cable box, etc.) and the display equipment (TV, display, projector, etc.) are turned off. Step 1 Connecting Source Components To The Transmitter A. HDMI Media Sou...
Page 20 - Tips; D. Component Media Source
20 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 A. Connect the provided IR Flasher to the IR-OUT port of the Transmitter. B. Find the location of the IR widow on your component and adhere the IR Flasher Eye directly over the IR window of your component. Note: One IR Flasher eye is to be used for one c...
Page 22 - Ensure that cables are properly connected.
22 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 While turning on the display device, the HD Flow Pro Wireless Multimedia Kit will be going through the start up process. The process takes about 1.5 to 2 minutes to complete. The Power/Link Indicator Light on the Transmitter and the Receiver should be fl...
Page 23 - Selecting Input and Output Port
23 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 Notes: 1. Audio and video sources will switch simultaneously whether using the remote or Power/Source Selection Button. 2. Independent audio switching is only allowed for AV and PC audio. 3. Inputs on the Transmitter and Receiver can be switched by point...
Page 25 - Indicator Lights Decoded
25 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 Step 5 Under the heading “Streaming I/F” use the pull down menu to change WiFi to LAN. Step 6 Enter the proper IP address, for the unit being set up, based on the network's domain. Step 7 Once all the settings have been entered click the Submit button at...
Page 26 - IR Flasher; IR Extender; in the; Product Modes; guration for applications where wireless signal transfer
26 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 Receiver • HDMI, COMPO, AV - The indicator light will be solid for the selected port as long as the output cable is present and connected to the output device. If no output device is detected by the selected output port, the indicator light will be fl as...
Page 27 - Multicast Modes; Multicast Wireless Mode; USB Multicast Set-Up Method
27 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 Note: Peer-to-Peer units can be con fi gured to multicast mode using the USB Multicast Set-Up Method or LAN Multicast Set-Up Method. Additional Receivers (HDS200-R) are required and sold separately. Please visit http://www.hdfl ow.com/Tech-Support for pr...
Page 28 - FAQs
28 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 Q. What compression standard does the HD Flow use to stream Full HD 1080p content? A. H.264 Baseline Pro fi le Level 4.2 video compression. Q. Does HD Flow Pro Wireless Multimedia Kit deliver 5.1 audio? A. No, the HD Flow Pro Wireless Multimedia Kit only...
Page 29 - Note; : different digital audio sources cannot be mixed.
29 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 Q. Can the HD Flow Pro Wireless Multimedia Kit be set to default to a speci fi c input/output if the unit is turned off or power is lost? A. Yes, the HD Flow Pro Wireless Multimedia Kit can be set to desired input and output ports via a programming page ...
Page 30 - Firmware Upgrade; Appendix
30 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 Factory Reset CAUTION Factory reset will revert all settings to factory defaults. It is not recommended to perform factory reset on multicast systems (systems that have two or more Receivers). If there are issues with multicast systems, please reference ...
Page 31 - How to Check Firmware Version; Transmitter Designation
31 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 How to Check Firmware Version Step 1 Connect the Receiver that needs its fi rmware to be checked to the display device (reference the installation section of this manual). Step 2 Plug in the power AC adapter into a power outlet, and then connect the powe...
Page 32 - Supported Video Formats
32 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 HDMI D Ͳ Sub AV(CVBS) HDMI COMP AV(CVBS) O O X O X X O O X O X X O O X O X X O O X O X X O O X O X X O O X O X X O O X O ^ X O O X O X X O O X O X X O O X O ^ X O O X O X X O O X O X X O O X O X X O O X O ^ X O O X O X X O O X O X X O O X O ^ X O O X O X...
Page 33 - FCC Compliance; Increase the separation between equipment and Receiver.; CE Compliance
33 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 FCC Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential...
Page 34 - YEAR LIMITED WARRANTY; Warranty
34 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 1 YEAR LIMITED WARRANTY The HDS200 is distributed by Peerless Industries, Inc. using the highest quality components andtechnology available. The Product is warranted to be free from defects in material and workmanship,given normal use and care, for 1 Yea...
Page 35 - Customer Care; Contact Information
35 of 36 ISSUED: 07-24-12 SHEET #: 180-9023-1 Customer Care Need help with installation or set up? Call Peerless-AV Customer Care 1-1-800-865-2112 (available 7:00am- 7:00pm CST, Monday - Friday), or email us at [email protected]. Peerless -AV 2300 White Oak Circle Aurora, IL 60502 USA www.hd fl o...
