Peavey PCX-V12 - Manual - manualsarea.com

Page 3 - INTRODUCTION; Thank you for selecting a Peavey Pro Comm PCX-; True Diversity Receiver; The Peavey Pro Comm PCX-V12 quartz controlled; UNIT FEATURES AND FUNCTIONS

INTRODUCTION Thank you for selecting a Peavey Pro Comm PCX- V12 quartz controlled single channel true diversity wirelessmicrophone system. Before operating and installing thissystem please read this instruction manual carefully andthoroughly in order to attain the correct operatingprocedures and to ...

Page 4 - Adjusts the AF output level of the receiver.

1. Antenna Input Connector A 2. Power Switch and Indicator: When the switch is turned on the red indicator illuminates to denote normal power status. 3. RF Signal Level Indicator: Indicates the RF signal strength received from the microphone. As soon as the signal is emitted from the microphone the ...

Page 5 - Connect the 12V DC plug from the AC/DC adapter.; Balanced Audio Output Jack:; XLR type connector; Unbalanced Audio Output Jack:

7. DC 12V Input Jack: Connect the 12V DC plug from the AC/DC adapter. 8. Balanced Audio Output Jack: XLR type connector 9. Unbalanced Audio Output Jack: 1/4" Phone Jack 10. Unbalanced Level Switch: “LOW selection is for “Microphone-Level” output. “HIGH” selection is for “Line-Out” level output. ...

Page 6 - GND PIN 1

3. Audio Output Connection: a. Unbalanced Level Switch Setting Position: Make sure to match the unbalanced output setting to the device input setting. The incorrect setting could result in low sensitivity level or over load distortion. Ex. (If you are going into the “Line” input on a mixer or amplif...

Page 7 - Align and fasten the rack mount

3. TWO 19/2-INCH UNITS RECEIVER INSTALLATION A. Setup for single half-rack receiver 1. Push the rack mount brackets (RM-11) upwards until it is firmly attached to the receiver. (Figure 5) Figure 5 B. Setup for dual half-rack receivers 1. Remove the screws at the top and bottom of the receiver where ...

Page 10 - The level

microphone the AUDIO LED indicators will illuminate according to the strength of sound level. If the LEDs do not illuminate or sound isnot present at the output, the system is not functioning properly and must be checked. 4. Receiver and Amplifier Volume Adjustment:a. Single-channel Unbalanced Audio...

Page 12 - Caution

5. Caution 1. Since the installation of the antenna influences the operating efficiency of the receiver, the most important rule is to minimize the distance as much as possible between the receiving antennaand the microphone for the best reception and performance. 2. The output voltage of the extern...

Page 13 - HANDHELD WIRELESS MICROPHONE; The Peavey Pro Comm PCX-V12 handheld wireless; Battery Status Indicator:; Designed to accommodate one 9V battery.

HANDHELD WIRELESS MICROPHONE The Peavey Pro Comm PCX-V12 handheld wireless microphone is a modular design. It also incorporates“Superior frequency tracking and muting techniques” dual-squelch to eliminate noise interference. 1. Unit Features and Functions1. Grille: Protects cartridge and prevents br...

Page 15 - BELT PACK TRANSMITTER; Connects to the; Transmitting Antenna:; transmitting antenna

4. When the microphone is not in use make sure to turn it off to extend the battery life. Remove the battery from the battery compartment if the microphone will not be in use for a long period of time. If a rechargeable battery is used take it out for a recharge as necessary. BELT PACK TRANSMITTER 1...

Page 16 - Indicates the power; Battery Compartment and Cover:

4. Gain Control: Adjusts the input gain to an appropriate level. 5. Transmitter Housing: Contains the PCB and battery. 6. Battery Status Indicator: Indicates the power on/off and battery status. a. When the power switch is turned on the LED indicator flashes briefly, indicating normal battery status...

Page 19 - SPECIFICATIONS

SPECIFICATIONS 1. Overall: VHF PCX-V12 1. Carrier Frequency Range: VHF Band 160~250 MHz 2. Oscillation Mode: Quartz-controlled 3. Channel: 1-channel fixed 4. Stability: + 0.005 % with temperature compensation 5. Max. Deviation: + 15 KHz with level limiting 6. Dynamic Range: > 110 dB 7. S/N Ratio:...

Page 20 - TROUBLESHOOTING GUIDE; MULITPLE SYSTEM

20 TROUBLESHOOTING GUIDE Symptom Distance Possible PossibleCause Solution No AF signal Any low transmitter replace battery and no RF signal battery voltage No AF signal long out of range move transmitter and no RF signal closer to receiver or obstecles No AF signal any microphone or check input sour...

Page 22 - PEAVEY ELECTRONICS CORPORATION LIMITED WARRANTY

PEAVEY ELECTRONICS CORPORATION LIMITED WARRANTY Effective Date: July 1, 1998 What This Warranty Covers Your Peavey Warranty covers defects in material and workmanship in Peavey products purchased and serviced in the U.S.A. and Canada. What This Warranty Does Not Cover The Warranty does not cover: (1...

Page 24 - Features and specifications subject to change without notice.