Peavey CS 800H - Manual

Peavey CS 800H

Peavey CS 800H – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
57 Page 57
58 Page 58
59 Page 59
60 Page 60
Page: / 60

Table of Contents:

  • Page 5 – W I R E G A U G E C H A R T
  • Page 12 – CS 800H Block Diagram
  • Page 17 – C S
  • Page 42 – Glosario de Términos
  • Page 57 – OT
  • Page 59 – PEAVEY ELECTRONICS CORPORATION LIMITED WARRANTY
Loading the manual

CS

®

800H Operations Manual

For more information on other great Peavey products, go to your local Peavey dealer or online at www.peavey.com

power amplifier

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 5 - W I R E G A U G E C H A R T

5 O Op pe erra attiin ng g P Prre ecca au uttiio on ns s Make sure the mains voltage is correct and is the same as that printed on the rear of the amplifier.Damage caused by connecting the amplifier to improper AC voltage is not covered by any warranty. Seethe Connecting Power section for more infor...

Page 12 - CS 800H Block Diagram

12 CC SS 88 00 00 HH BB lloo cckk DD iiaa gg rraa mm +- LO PASS HI PASS HI PASS 2 1 +- LO PASS HI PASS HI PASS 2 1 Mode Output Crossover LFC Amplifier RampUp Low Cut Function Amp Output Low Pass Hi Pass / Full RangeOutput Attenuator Input Adjust Adjust Switch Switch Low Cut Protection DDT Power Ampl...

Page 17 - C S

17 Rated output power (120 VAC, 60 Hz): Bridge mode, mono: 4 Ohms: 800 W @ 1 kHz, <0.1% THD 8 Ohms: 650 W @ 1 kHz, <0.1% THD Stereo mode, both channelsdriven: 2 Ohms: 400 W per channel 1 kHz, <0.05% THD 4 Ohms: 325 W per channel 1 kHz, <0.05% THD 8 Ohms: 225 W per channel 1 kHz, <0.05...

Other Peavey Models

All Peavey Other