Page 2 - Table of Contents
2 Table of Contents Warnings and precautions ........................................................ 3 Warnings ......................................................................... 3 Precautions ..................................................................... 3 Cautions when in use .........
Page 3 - Warnings and precautions; Warnings; Precautions
3 Warnings and precautions Warnings Do not allow the equipment to get wet. • If liquid splashes onto the equipment, wipe off with a dry cloth. In the unlikely event that liquid gets inside the product, unplug the USB cable and contact your dealer. Using the product with liquid still inside may cause...
Page 4 - Cautions when in use; Setup location
4 Cautions when in use Always keep the touch panel clean • This optical touch panel utilizes infrared rays and may operate incorrectly if the infrared transmissive part becomes soiled. Use a soft dry cloth to clean the infrared transmissive part once every day. Use a power supply within the rated vo...
Page 5 - Maintenance; If something abnormal happens
5 Maintenance ∗ Be sure to unplug the USB cable before cleaning the equipment. Clean the inside of the equipment once a year. • The equipment is of semi-sealed construction, so dust may eventually accumulate inside. This may cause poor operation due to a reduction in the level of infrared light avai...
Page 6 - Accessories; Touch panel unit
6 Accessories Check that all accessories are included. Quantities are indicated in parentheses. USB cable (1)Length: 2 m (6.56 ft) Mounting brackets [A]TY-TP42P6-S (4)TY-TP50P6-S (5) Mounting screwsfor [A]TY-TP42P6-S (8)TY-TP50P6-S (10) CD-ROM (1)• USB driver software• Touch Panel Driver software Li...
Page 7 - Setup procedure; Installation of Touch Panel Driver
7 Setup procedure 1 Attachment of the touch panel tothe plasma display ................ P 8 2 Connection between the computerand the plasma display .............. P 10 4 Installation of Touch Panel Driver .............. P 21 5 Set up Program .............. P 23 3 Installation of USB Driver ............
Page 8 - Attachment of the touch panel to the plasma display
8 Never attach a plasma display onto the touch panel by placing the touch panelon a flat surface. Doing so may damage the infrared sensor on the touchpanel.If you cause a malfunction by attempting attachment in this way, you will becharged for repairs. Attachment precautions A t t a c h t h e m o u ...
Page 9 - Fasten the touch panel.; Lower the tentatively fastened mounting bracket.
9 Fasten mounting brackets [A] to the display. TY-TP42P6-S: 4 points in total TY-TP50P6-S: 5 points in total Fasten mounting brackets. [A] 5 Fasten the touch panel to the display.After hand tightening the bracket mounting screws, tightenthem further using a flathead screwdriver. Fasten so thereis no...
Page 10 - Connection between the computer and plasma display; Connection with computer
10 Connection between the computer and plasma display USB Pen OFF ON Connection with computer ∗ Check that the USB power supply of the computer being used is rated at 500 mA. (1) Connect the plasma display and computer with the VGA cable.(2) Turn on power in the following sequence: 1: Plasma Display...
Page 11 - Installation of the USB Driver; Function
11 Installation of the USB Driver Function The control software provides the following functionality. • Supplies a software interface for application programs that simulates the output of a mouse. This is achieved by converting touch panel output data into that which is compatible with the protocol ...
Page 12 - Install USB Driver; In case of Windows 98 / SE
12 Installation of the USB Driver First, PC is started, and then Windows is started.The CD-ROM with USB driver software is inserted into theCD-ROM drive.Next, touch panel and PC are connected with a USB cable.(see page 10)When a USB cable is connected, “Add New HardwareWizard” is indicated. 1 Click ...
Page 13 - COM port number is confirmed with “Device Manager”
13 Installation of the USB Driver Setup is completed when all the files of the driver are copied. 7 Click to close this wizard. 1 Click on [Start] [Settings] [Control Panel] Double-click on “the system” icon of the control panel,and open the properties of the system. The properties of the system are...
Page 14 - In case of Windows ME
14 In case of Windows ME First, PC is started, and then Windows is started.The CD-ROM with USB driver software is inserted into theCD-ROM drive.Next, touch panel and PC are connected with a USB cable.(see page 10)When a USB cable is connected, it is recognized as a newhardware, and a message is indi...
Page 18 - PC is started, and then Windows is started; In case of Windows XP
18 Installation of the USB Driver PC is started, and then Windows is started In case of Windows XP Install USB Driver Next, though the following warning message is indicated,there is no problem. 2 Click on this button. First, PC is started, and then Windows is started.The CD-ROM with USB driver soft...
Page 21 - Installation of the Touch Panel Driver; Install Touch Panel Driver
21 Installation of the Touch Panel Driver The CD-ROM contains two different types of controlsoftware installers (one for Windows 98SE and WindowsME, and one for Windows 2000 and Windows XP). Startthe set-up file corresponding to the OS you are using. Note: When a previous version driver software has...
Page 22 - Uninstallation of the Touch Panel Driver; USB driver software
22 Delete “tpdrv” from the “Add/Remove Programs” of the “Control Panel”. (1) Click on [Start] [Settings] [Control Panel] (2) Double-click on [Add or delete applications].(3) Click on the [Uninstall] tab.(4) Select "tpdrv" and click on the [Change and delete] button. (5) The file delete confi...
Page 23 - Setup program
23 Setup program The setup program is to set communication ports and various operation modes and to carry out calibration or so on.Performing setup in the initial state saves the modified contents in “tpdrv.ini” setting file in “C:\Program Files\tpdrv”folder. Those contents are still valid at the ti...
Page 24 - Setup of basic settings
24 If the “Touch Error” is set “On”, a warning is indicated whenan internal error occurs in the touch panel driver. Touch Error Warning Communication Port This sets the COM port of connecting PC.The port being used for connection with the touch panel isselected. Setup program When “Auto connect” is ...
Page 26 - Calibration Screen
26 Setup program Pressing the [Calibration] button on the main window activates the calibration screen to carry out calibration of thedetection of the Touch Panel and PC (in order to place the mouse cursor at the touched position). Briefly touch the center of the target displayed on the screen in or...
Page 27 - User Setting
27 Setup program The following window is displayed by pushing the user setting button of the Touch Panel setting program menu. User Setting Click Mode (See next page) Double click Time Time interval when double-clicking is set up.Time between the first touch and the second touch isset. When the seco...
Page 29 - TroubleShooting; Before requesting repairs
29 TroubleShooting Before requesting repairs Please check the following points. Symptom No response at all toinput Suddenly stopsresponding duringoperation Response is slow There are times whenthere is no response Check Check the USB cable Check that the USB cable is securely connected. Check extran...
Page 30 - Specifications
30 Specifications Model Number Type Power Source Voltage Electric current Supply system Touch Panel Detection system Panel window (W × H) Detection range (W × H) Effective detection range Operating modes Resolution (W × H) Detection pitch Output system Number of optic elements (W × H) Optic element ...
