Panasonic PT-DW10000 - Manual
Panasonic PT-DW10000 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 5 – Extended format for lens; Start; End; command
- Page 6 – Cable specifications; fits to your personal computer.; Transmission from the computer; Attention; Self-diagnosis result read commands is binary 4 byte command.; Responses from the projector
- Page 8 – Example; Receive (the data received by the computer); Note
The main unit is equipped with SERIAL terminals located in its terminal section on the side, and this terminal is
compliant with RS-232C.
Panasonic Projectors RS-232C Control Specifications
PT-D10000/DW10000 PT-D7700/DW7000 PT-D5600/DW5000 PT-D5500 PT-D3500
Pin assignments and signal names
Communication conditions (Factory setting)
Basic format
Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent in this
order. Add parameters according to the details of control.
Start
ID designate
3 command
characters (3 bytes)
Parameter
(undefined length)
End
Two ID characters
(2 bytes)
Semicolon
Colon
ZZ, 1 to 64 and 0A to 0Z
STX
C1
C2
C3
:
P1
P2
Pn
ETX
A D
I 1
I 2
;
Attention
Note
D-Sub 9-pin (female),
external appearance
Serial input terminal
Pin No. Signal name
TXD
RXD
GND
CTS
RTS
Description
NC
Send data
Receive data
Connected internally
Ground
NC
Connected internally
NC
D-Sub 9-pin (male),
external appearance
Serial output terminal
Pin No. Signal name
RXD
TXD
GND
RTS
CTS
Description
NC
Receive data
Send data
NC
Ground
NC
Connected internally
NC
Signal level
Synchronization method
Baud rate
Parity
Character length
Stop bit
X parameter
S parameter
RS-232C-compliant
Start-stop synchronization
9 600bps
None
8 bits
1 bit
None
None
If a wrong command is received, the projector will send an ER401 or ER402 command to the computer.
Projector ID supported on the RS-232C interface is ZZ (ALL) and a group of 1 to 64 and 0A to 0Z.
If a command is sent with a projector ID specified, the projector will return answer back only in the
following cases:
If it coincides with the projector ID,
ID specification is ALL and VPS-SYSTEM is the master, or
ID specification is group and Group is the master.
No command can be sent or received for 10 to 60 seconds after the lamp starts lighting. Try
sending any command after that period has elapsed.
When sending several commands, be sure to wait for more than 0.5 seconds after receiving a
response from the projector, and then send the next command.
When sending commands without parameters, a colon (:) is not necessary.
1
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
P1 P2 P3 Function D10000/DW10000 D7700/DW7000 D5600/DW5000/D5500 D3500 0x00 0x00 0x00 HORIZONTAL SHIFT RIGHT SLOW YES YES NO NO 0x00 0x01 0x00 HORIZONTAL SHIFT RIGHT NORMAL YES YES NO NO 0x00 0x02 0x00 HORIZONTAL SHIFT RIGHT FAST YES YES NO NO 0x00 0x00 0x01 HORIZONTAL SHIFT LEFT SLOW YES YES NO NO ...
Cable specifications To connect the computer to the SERIAL terminal, prepare an adequate communication cable that fits to your personal computer. Projector 1 2 3 4 5 6 7 8 9 NC NC NC NC Computer (DTE specifications) <Connecting to a PC> 1 2 3 4 5 6 7 8 9 NC NC NC NC Transmission from the compu...
Example -When the transmission ID from PC is ID ALL and the projector ID is ALL, Send (the data sent from the computer) 0x02 0x00 0xfe 0x03 Receive (the data received by the computer) 0x02 0x00 0xfe 0x10 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x03 Self-diagnosis information is x10000000, or bit 28 is on...
