OmniMount Lift 42 - Manual - manualsarea.com

Page 2 - DO NOT EXCEED THE MAXIMUM WEIGHT CAPACITY FOR THIS PRODUCT; OMINMOUNT PRODUCT WARRANTY; Specifications are subject to change without prior notice.

2 WARNING – ENGLISH WARNING! SEVERE PERSONAL INJURY AND PROPERTY DAMAGE CAN RESULT FROM IMPROPER INSTALLATION OR ASSEMBLY. READ THE FOLLOWING WARNINGS BEFORE BEGINNING. If you do not understand the instructions or have any concerns or questions, please contact a qualified installer. North Americ...

Page 3 - Contents

3 Contents Power cable 1 14 Motor cable 1 13 Screen Adapter 1 12 Vertical Extension Rails and covers 2 11 Universal Adapter 1 10 Corner brackets 2 9 IR Receiver/Control switch 1 8 Remote Control 1 7 Control Box 1 6 Top Plate 1 5 Screen Support 1 4 Bayonet Bracket 1 3 Lift Column 1 2 Base Mount 1 1 C...

Page 5 - Before Installation

5 PINCH POINT WARNING! • Improper construction of lift enclosure can create dangerous pinch points. It is the responsibility of the installer to ensure the intended use of this product does not create hazardous pinch zones. Installation design should prevent users from inserting objects between mo...

Page 6 - Before Enclosure Construction!; Minimum INTERIOR Dimensions

6 Before Enclosure Construction! Assemble lift mechanism and connect the TV to be used in the install to determine dimensions for the lift enclosure prior to construction. Be sure to leave room for adjustments If necessary. An out of cabinet assembly of the mechanism can be done using steps 1,4,6,...

Page 7 - Measurements Required For Cabinetry Dimensions; Height

7 Measurements Required For Cabinetry Dimensions Use previous page to find the minimum INTERIOR dimensions for custom enclosures. Height Width Depth

Page 8 - • Using the small Hex wrench and 6mm x 20mm screws (O), connect the base

8 Step 1 O 1 2 x4 Attach the Base Bracket (1) to the Lift Column (2): • Using the small Hex wrench and 6mm x 20mm screws (O), connect the base bracket to the lift column. Note that one side is counter sunk to ensure flush installation of screws. Hand tighten all four screws before proceeding. If t...

Page 10 - Secure Lift Column and Base Bracket in enclosure:

10 Step 3 Figure A Figure B 3 2 Secure Lift Column and Base Bracket in enclosure: • Gently glide the lift column into place on the bayonet bracket so that the tapered slots on the column are secured to the extrusions on the bracket. Gently push down until the base bracket is touching the bottom of...

Page 11 - TOP

11 Step 4 x4 4 4 12 12 TOP S Connect Screen Adapter (12) to the Screen Support (4): • Use the large hex wrench to secure the screen adapter to the screen support using four 3/8-16 x ¾” screws (S). Depending on TV size and mounting hole pattern the screen adapter can be vertically adjusted for opti...

Page 13 - Figure A

13 Attach the Screen Support(4) and Top Plate(5) to the Lift Column(2): • Before attaching the top plate ensure that the rubber guide on the “pigtail” is secured in the square cutout on what will be the front of the lift column (fig. A). Failure to do so may result in damage to the wire. • Once th...

Page 14 - Attach lift assembly to enclosure base:

14 Step 7 2 1 Q x4 Attach lift assembly to enclosure base: • Using a level on the top plate ensure that the lift column and assembly are level within the enclosure. Gently tap the base of the column left or right to bring the top plate level. • Using four #10 x ¾” (Q) screws attach the base bracke...

Page 15 - Note; : IF MONITOR SCREWS “BOTTOM OUT”, THEN USE ADDITIONAL WASHERS; TV; Attach the Universal Adapter to the TV:; • Place the TV face down on a protected surface.

15 Step 8 11 M-A – M-L M-A – M-L 10 10 Note : IF MONITOR SCREWS “BOTTOM OUT”, THEN USE ADDITIONAL WASHERS (not included) TO TAKE UP THE SLACK. TV Attach the Universal Adapter to the TV: • Place the TV face down on a protected surface. • For larger TV’s, the vertical rails may need swapped out for ...

Page 16 - Connect the TV and universal adapter to the lift column:

16 Step 9 Figure B Figure A Figure C Connect the TV and universal adapter to the lift column: • Partially install two ¼-20 x ½” (W) hex screws into the top rear of the universal adapter (fig. A). • Lift and lock TV into position on screen adapter (fig. B). • Install two remaining hex screws throug...

Page 17 - Install universal adapter rail covers:

17 Step 10 Install universal adapter rail covers: • Carefully attach the correct plastic covers to the universal adapter.

Page 18 - Appendix; Using guide pins for a floating top:; points. A template has been included to assist with guide pin use.; Guide pins

18 Appendix Using guide pins for a floating top: • The guide pins are recommended for use as a safety measure to prevent pinch points. A template has been included to assist with guide pin use. • If the guide pins are to be used, make sure the top surface of the enclosure will not be used as a loa...

Page 19 - Guide Pin/Top Plate Template

Page 20 - Thank you for purchasing an OmniMount product.

20 OmniMount Systems, Inc. 8201 South 48th Street Phoenix, AZ 85044-5355 1-800-MOUNT-IT 1-800-668-6848 www.omnimountpro.com Thank you for purchasing an OmniMount product.

OmniMount Lift 42 - Manual

Table of Contents:

Summary

Other OmniMount Models