Page 2 - Before use, be sure to read the precautions printed on the package.; For safe use
E-1 Introduction ● Unauthorized copying of this manual in part or in full, except forprivate use, is prohibited. Unauthorized reproduction is strictly prohibited. ● OLYMPUS CORPORATION shall not be responsible in any wayfor lost profits or any claims by third parties in case of any damageoccurring f...
Page 3 - WARNING
E-2 1. Keep this product out of the reach of babies, infants, and children. There is the possibility of occurrence of the following types ofaccidents. Injury by dropping onto the body from a height. Injury from parts of the body getting caught in parts which openand close. Swallowing of small parts....
Page 4 - Batteries
E-3 Batteries ● Always use lithium ion battery packs manufactured by Olympusand bearing the Olympus brand. For more details, refer to yourcamera's instruction manual. ● Take care that the battery electrodes do not become wet. This maycause trouble or accidents. ● Carefully read the instruction manua...
Page 5 - For Prevention of Water Leakage Accidents; Hair
When water leakage occurs while this product is being used, repair of thecamera housed in this product may become impossible. Please observethe following cautions for use.1. When sealing this product, make sure that no hairs, fibers, sand particles or other foreign matter stick not only to the O-rin...
Page 6 - Handling the Product
E-5 Handling the Product ● Use or storage of the product at the following locations may causedefective operation, defects, trouble, damage, fire, internal clouding, orwater leakage. Always avoid these locations. Locations reaching high temperatures such as those under directsunlight, in an automobil...
Page 8 - Contents
E-7 Introduction ................................................................................E-1Please read the following items before use ..............................E-1For safe use ..............................................................................E-1Batteries .......................
Page 10 - Check the contents of the package.
E-9 1. Preparations Check the contents of the package. Check that all accessories are in the box.Contact your dealer if accessories should be missing or damaged. 取 扱 説 明 書 デ ジ タ ル カ メ ラC A M E D I A C - 7 6 0 U l t r a Z o o m ／ C - 7 7 0 U l t r a Z o o m 用 ■このたびは、防水プロテクタPT-022をお買上げいただき、ありが...
Page 11 - Names of the parts; Note : The Case operation parts marked by
E-10 Names of the parts Note : The Case operation parts marked by ❈ corresponds to the operation parts of the digital camera. When the operation parts of the Case are operated,the corresponding functions of the digital camera will operate. For detailsof the functions, refer to the instruction manual...
Page 12 - Install the strap on the Case body.; CAUTION; Installation explanation; Hand strap; Finished installation
E-11 Install the strap. Install the strap on the Case body. : Please install the strap correctly as shown above. OLYMPUS CORPORATION shall bear no responsibility for damage etc. causedby dropping the Case because of incorrect installation of the strap. CAUTION : • Do not exert excessive force onto t...
Page 13 - How to Press the Shutter; manual for the digital camera.; How to Use the Zoom Lever
E-12 How to Press the Shutter When pressing the shutterlever, press it gently, so thatthere will be no movement ofthe camera. Note: • For detailed operation of the shutter, refer to the instruction manual for the digital camera. How to Use the Zoom Lever Zoom operation is possibleby operating the zo...
Page 14 - • When loading the camera, confirm that the projecting; ) Gently turn the power switch dial knob
E-13 Setting the Zoom Lever W h e n l o a d i n g t h e d i g i t a lcamera in the Case, fit theprojecting part of the zoomlever of the digital camera intothe recessed part of the zoomlever on the inside of the Case. How to switch the power ON The method of turning this product ON is variable depend...
Page 16 - the instruction manual for the camera.; Flash operation procedure
E-15 Note: • For details about using the flash for taking pictures, refer to the instruction manual for the camera. Flash operation procedure Press the flash button to raise the flash out of the camera.Moving the flash storage button again to store the flash inside thecamera. PT̲022̲E.qxd 2004.3....
Page 17 - Removing the TLL cable connector cap; Turn counter clockwise.; Gently turn the cap; • I f t h e T T L c a b l e c o n n e c t o r c a p i s l o o s e , w a t e r
E-16 Removing the TLL cable connector cap T TL flash shooting by combining this case (PT-022) and the case forFL-20 flash (optional PFL-01): TTL cable connector cap Turn counter clockwise. Remove. Underwater TTL cable Insert into the connector. Turn the threaded section of the connectorclockwise lig...
Page 18 - Removing the hot shoe cable cap; • Be sure to remove the camera from the case when; • If you cannot disconnect the TTL cable, do not use
E-17 Removing the hot shoe cable cap To perform TTL flash shooting when this case is used, connect thehot shoe cable provided with the optional PFL-01 between theconnector on this case and the C-770 Ultra Zoom's hot shoe. 1 Turn the hot shoe cable connector cap insidethe case counterclockwise to rem...
Page 19 - Advance Check of the Case; Advance test before use; Before installing the digital camera in the Case, immerse the
E-18 2. Advance Check of the Case Advance test before use This Case has been the subject of thorough quality control for the partsduring the manufacturing process and thorough function inspectionsduring the assembly. In addition, a water pressure test is performedwith a water pressure tester for all...
Page 20 - Check the digital camera.; Check the digital camera before loading it in the Case.; Battery Confirmation; Note : • In order to avoid losing shutter chances due to an exhausted; Loading in the Case; • If the digital camera is inserted into the case without
E-19 3. Install the digital camera. Check the digital camera. Check the digital camera before loading it in the Case. Battery Confirmation As the LCD monitor is used for picture confirmation while takingpictures under water, the battery life becomes short.Confirm that the remaining battery capacity ...
Page 21 - • Make sure that the flash is closed when loading the
E-20 Check the operation of the camera. Confirm the operation according to the instruction manual for the digital camera. Load the digital camera. Open the Case. Insert the buckle opener of the accessory into the buckle opening leveras shown in the figure (in direction ) Pull the buckle opener slowl...
Page 22 - Insertion of silica gel; Pay attention to the orientation.; • Insert the silica gel all the way at the specified location
E-21 Insertion of silica gel Pay attention to the orientation. Before sealing the Case, insert the accessory silica gel bag forprevention of fogging between the bottom of the camera and theCase. Insert the bag with the glued longer side to the inside. : • Insert the silica gel all the way at the spe...
Page 23 - • Seal the Case by turning both buckle lock levers; Has the O-ring at the Case opening part been installed properly?
E-22 Install the special balance weight. Seal the Case. Check the loading status. : • Seal the Case by turning both buckle lock levers down in arrow direction. When one of the buckles isleft open, the Case will not be sealed and waterleakage will be caused. CAUTION When the rear lid is closed(quietl...
Page 24 - Installation
E-23 Installation and Removal of the LCD Hood Installation Strongly push the mounting projections of the LCD hood as shownin the figure into the guides above and below the LCD monitorwindow. Removal Remove the mounting projections of the LCD hood from theguides above and below the LCD monitor window...
Page 25 - • After loading the camera into the Case, confirm that the; • Hairs, fibers, and other narrow items are not very apparent,
E-24 Perform the final checks. Visual Inspection After sealing the Case, check the sealing part of front and rear lidvisually to confirm that the O-ring is not twisted or out of the grooveand that no foreign matter has been caught. Fit the lens cap onto the lensring as shown in the figure. Besure to...
Page 26 - Final Test; Hints
E-25 Now everything is all right!Have a nice dive!Did you remember to attach thebalance weight? Final Test The final test after loading the camera is explained below. This is the only way toeliminate worry about possible entry of water! Always perform this test. It can beperformed easily in a water ...
Page 27 - Taking Pictures Under Water; How to Use the Hand Strap
E-26 4. Taking Pictures Under Water How to Use the Hand Strap Pass your hand through the accessory hand strap and adjust thelength with the stop button. Take pictures carefully. Confirm the picture on the LCD monitor. T h i s C a s e u s e s t h e L C D m o n i t o r t o c o n f i r m t h e p i c t ...
Page 28 - Handling After Shooting; Wipe off any waterdrop.
E-27 5. Handling After Shooting Wipe off any waterdrop. After completing the shootingand returning to land, wipe offany waterdrop sticking to theCase. Use air or a soft cloth notleaving any fibers to thoroughlywipe any waterdrop etc. fromthe joint between the front andrear lid, the shutter lever, th...
Page 29 - Take out the digital camera.; : • Always place the opened Case with the O-ring side
E-28 Take out the digital camera. Open the case carefully, pull up the mode dial from the upper surface ofthe case to disengage it from the mode lever of the camera, and thenremove the digital camera from the case. : • Always place the opened Case with the O-ring side facing up. When the Case is pla...
Page 30 - Wash the Case with pure water.; : • Water leakage may be caused when a high water; : • Do not use hot air from a hair drier or the like for drying
E-29 Wash the Case with pure water. After use, seal the Case again after taking out the camera and wash itsufficiently in pure water as soon as possible. After use in sea water, it iseffective to immerse it for a fixed time in pure water to remove any salt. : • Water leakage may be caused when a hig...
Page 31 - Maintaining the Waterproof Function
E-30 6. Maintaining the Waterproof Function Remove the O-ring. Open the Case and remove the O-ring from the Case.Removal of the O-ring Insert the O-ring removal pick between the O-ring and the wall of theO-ring groove. Move the tip of the inserted pick under the O-ring. (Take care not todamage the O...
Page 33 - How to Apply Grease to the O-ring; • A l w a y s p e r f o r m m a i n t e n a n c e o f t h e w a t e r p r o o f
E-32 1 Install the O-ring. Confirm that no foreign matter is attached, apply a thin coat of theaccessory grease to the O-ring, and fit the O-ring into the groove. Atthis time, confirm that the O-ring does not stick out from the groove. How to Apply Grease to the O-ring Apply theexclusivelubricant to...
Page 34 - Maintenance of the TTL Connector Cap; Waterproof cap
E-33 Clean and apply O-ring silicon grease to these sections. Maintenance of the threaded sections on the TTL cable and TTL cable connector If the threaded sections used to connect the TTL cable to the TTL cableconnector are not maintained properly, salt and other seawater residuemay adhere the TTL ...
Page 35 - Replace consumable products.; Note
E-34 Replace consumable products. The O-ring is a consumable product. Independent of the number oftimes the Case is used, it is recommended that the O-ring shouldbe replaced by a new one at least once a year. Deterioration of the O-ring is accelerated by the use conditions andthe storage conditions....
Page 42 - Specifications; Available models Olympus digital camera; Diver's Insurance Guide
E-41 Specifications ❈ We reserve the right to change the external appearance and thespecifications without notice. Available models Olympus digital camera CAMEDIA C-760 Ultra Zoom/C-770 Ultra Zoom Pressureresistance Depth of up to 40 m Main materials Body: Transparent polycarbonateBuckles: Stainless...
Page 43 - MEMO
E-42 MEMO PT̲022̲E.qxd 2004.3.18 4:34 PM ページE-42
