Page 2 - OLYMPUS CORPORATION; For safe use
E-1 Disclaimer ● Unauthorised copying of this manual in part or in full, except forprivate use, is prohibited. Unauthorised reproduction is strictlyprohibited. ● OLYMPUS CORPORATION shall not be responsible in any wayfor lost profits or any claims by third parties in case of any damageoccurring from...
Page 3 - WARNING
E-2 1. Keep this product out of the reach of babies, infants, and children. There is the possibility of occurrence of the following types ofaccidents. Injury by dropping onto the body from a height. Injury from parts of the body getting caught in parts which openand close. Swallowing of small parts....
Page 4 - Batteries; Rough handling, such as jumping into the water with the case in
E-3 Batteries ● Use an exclusive lithium-ion battery (Olympus BLM-1) designed fordigital cameras. ● Keep the battery's contacts away from damp or humidity; otherwisethis could impair performance and/or cause accidents. ● For additional battery cautions, refer to your digital camera'sinstruction manu...
Page 5 - For Prevention of Water Leakage Accidents; The O-ring is a consumption product. Please replace it at least; Examples for foreign matter sticking to the O-ring
E-4 For Prevention of Water Leakage Accidents When water leakage occurs while this product is being used, repair ofthe camera housed in this product may become impossible. Pleaseobserve the following cautions for use.1. When sealing this product, make sure that no hairs, fibers, sand particles or ot...
Page 6 - Handling the Product
E-5 Handling the Product ● Use or storage of the product at the following locations may caused e f e c t i v e o p e r a t i o n , d e f e c t s , t r o u b l e , d a m a g e , f i r e , i n t e r n a lclouding, or water leakage. Always avoid these locations. Places where high temperatures exist, su...
Page 8 - Removing the filter from the digital camera; Contents
E-7 Disclaimer ..................................................................................E-1Please read the following before using the product ..................E-1For safe use ..............................................................................E-1Batteries ...........................
Page 10 - Check the contents of the package.; Case body; Instruction manual
E-9 1. Preparations Check the contents of the package. Check that all accessories are in the box.Contact your dealer if accessories should be missing or damaged. 取 扱 説 明 書 デ ジ タ ル カ メ ラC A M E D I A C - 8 0 8 0 W i d e Z o o m 用 ■このたびは、防水プロテクタPT-023をお買上げいただき、ありがとうご ざいます。 ■この説明書をよくお読みのうえ、安全に正しくお使...
Page 11 - Names of the parts; Note : The Case operation parts marked by
LCD hood strapGrease for O-rings (White-cap tube)Silica gelBalance weightPick for removing O-ringsBuckle openerLens capBuckle open/close leverBuckle hook ❈ Quick View button ❈ Control dial knobStandard port O-ring (POL-104)W a t e r p r o o f c a p m a i n t e n a n c eadapterLCD monitor windowCamer...
Page 13 - How to Press the Shutter; Note; How to Use the Zoom Lever
E-12 How to Press the Shutter When pressing the shutter lever,press it gently, so that there willbe no movement of the camera. Note : • For more detailed information on operating the shutter release, please consult the digital camera’s instruction manual. How to Use the Zoom Lever Z o o m o p e r a ...
Page 14 - • When the setting is insufficient, the loading of the camera; • Once the flash is up, it cannot be retracted as long as the; CAUTION
E-13 Setting the Zoom Lever When loading the digital camera in theCase, fit the projecting part of the zooml e v e r o f t h e d i g i t a l c a m e r a i n t o t h erecessed part of the zoom lever on theinside of the Case. Power Switch Button Operation Method Press the power switch buttonto switch ...
Page 15 - • If the standard port is attached improperly to the case,; Removing; Removing/attaching the standard port
Boss Buckle E-14 : • If the standard port is attached improperly to the case, water penetration may result. Also make sure that thebuckles on the left and right of the standard port areclamped firmly. CAUTION Removing First wipe any moisture off the case, and then slowly turnthe two buckles on eithe...
Page 16 - • The diffusion plate cannot be used when the PPO-05; Detaching; Detaching/attaching the diffusion plate
E-15 : • The diffusion plate cannot be used when the PPO-05 is mounted. CAUTION Detaching First make sure the case is completely dry. Whilegently holding the diffusion plate and standard port,slowly turn the two buckles on either side of thestandard port by about 110° in the opening direction(from d...
Page 17 - Removing the TTL cable connector cap
E-16 Removing the TTL cable connector cap TTL flash shooting is possible by uncapping the TTL cable connectoron this case (PT-023) and connecting the FL-20 flash case (optionalPFL-01) as described in the following procedure. T TL flash shooting by combining this case (PT-022) and the case forFL-20 f...
Page 18 - Removing the hot shoe cable cap; • Be sure to remove the camera from the case when; • I f t h e T T L c a b l e c o n n e c t o r c a p i s l o o s e , w a t e r
E-17 Removing the hot shoe cable cap To perform TTL flash shooting when this case is used, connect thehot shoe cable provided with the optional PFL-01 between theconnector on this case and the C-8080 Wide Zoom's hot shoe. 1 Turn the hot shoe cable connector cap insidethe case counterclockwise to rem...
Page 19 - Advance Check of the Case; Advance test before use
E-18 2. Advance Check of the Case Advance test before use This Case has been the subject of thorough quality control for the partsduring the manufacturing process and thorough function inspectionsduring the assembly. In addition, a water pressure test is performedwith a water pressure tester for all...
Page 20 - Advance Test; Main causes of water leakage are as follows.
E-19 Advance Test 1. Before installing the digital camera in the Case, immerse the empty Case to the intended water depth to confirm that there is no waterleakage. 2. Main causes of water leakage are as follows. The O-ring has not been installed. A part of the O-ring or the entire O-ring is outside ...
Page 21 - Check the digital camera.; Check the digital camera before loading it in the Case.; Battery Confirmation; • If the digital camera is inserted into the case without; • The digital camera cannot be inserted in the case if a
E-20 3. Install the digital camera. Check the digital camera. Check the digital camera before loading it in the Case. Battery Confirmation Since the LCD monitor is used for picture confirmation while takingpictures under water, the battery life becomes short.Confirm that the remaining battery capaci...
Page 22 - • Attach the camera mount in the proper direction as
① ② E-21 Lifting the mode dial knob Pull up the mode dial of the case until itstops, so that it does not interfere with themode dial of the digital camera. Open the Case. Insert the buckle opener of the accessory into the buckle openinglever as shown in the figure (in direction ) Pull the buckle o...
Page 23 - • Be sure to store the camera flash before loading the; Pay attention to the orientation.
E-22 Fitting the mode dial knob After the digital camera has been loaded, pushdown the mode dial of the case from the uppersurface of the case and set it so that the lower partof the mode dial of the case on the inside of thecase fits properly onto the upper part of the modedial of the digital camer...
Page 25 - Installation and Removal of the LCD Hood; Installation; Install the special balance weight.
Guides E-24 Installation and Removal of the LCD Hood Installation Strongly push the mounting projections of the LCD hood as shownin the figure into the guides above and below the LCD monitorwindow. Removal Remove the mounting projections of the LCD hood from the guidesabove and below the LCD monitor...
Page 26 - • After inserting the camera into the case, confirm that the; • Hairs, fibers, and other narrow items are not very apparent,
E-25 : • After inserting the camera into the case, confirm that the mode dial moves. If it does not move, oil or grease mayhave gotten on the mode dial. Wipe it clean. CAUTION Try to move the mode dial. After sealing, turn the mode dial knob and confirm that the modedial of the camera is switched. S...
Page 27 - Final Test
E-26 Final Test The final test after loading the camera is explained below. This is the only way toeliminate worry about possible entry of water! Always perform this test. It can beperformed easily in a water tank or a bathtub. The required time is about five minutes. Simple waterimmersion test Expl...
Page 28 - Taking Pictures Under Water; How to Use the Hand Strap
E-27 4. Taking Pictures Under Water How to Use the Hand Strap Pass your hand through thea c c e s s o r y h a n d s t r a p a n da d j u s t t h e l e n g t h w i t h t h estop button. Take pictures carefully. Confirm the picture on the LCD monitor. T h i s C a s e u s e s t h e L C D m o n i t o r ...
Page 29 - Handling After Shooting; Wipe off any waterdrop.
E-28 5. Handling After Shooting Wipe off any waterdrop. A f t e r u n d e r w a t e r s h o o t i n g ,remove any drops of water fromthe case. Use pressurized air ora soft, lint-free cloth to carefullywipe away any moisture from thehinge between the front and rearlids, the shutter release lever, the...
Page 30 - Take out the digital camera.; • After opening the case, always put it down it with the
E-29 Take out the digital camera. Open the case carefully, pull up the mode dial from the upper surface ofthe case to disengage it from the mode lever of the camera, and thenremove the digital camera from the case. : • After opening the case, always put it down it with the O-ring side face-up. Other...
Page 31 - Wash the Case with pure water.; • Water leakage may be caused when a high water; • Do not use hot air from a hair drier or the like for
E-30 Wash the Case with pure water. After use, seal the Case again after taking out the camera and wash itsufficiently in pure water as soon as possible. After use in sea water,it is effective to immerse it for a fixed time in pure water to removeany salt. : • Water leakage may be caused when a high...
Page 32 - Maintaining the Waterproof Function
E-31 6. Maintaining the Waterproof Function Remove the O-ring. Open the Case and remove the O-ring from the Case.Removal of the O-ring Insert the O-ring removal pick between the O-ring and the wall ofthe O-ring groove. Move the tip of the inserted pick under the O-ring. (Take care notto damage the O...
Page 34 - Waterproof cap
E-33 : • A l w a y s p e r f o r m m a i n t e n a n c e o f t h e w a t e r p r o o f function even when the Case has been opened toexchange the battery or the image storage duringshooting. Neglecting this maintenance may becomethe cause of water leakage. • When the Case is not to be used for a lon...
Page 35 - Replace consumable products.
E-34 Replace consumable products. The O-ring is a consumable product. Independent of the number oftimes the Case is used, it is recommended that the O-ring shouldbe replaced by a new one at least once a year. Deterioration of the O-ring is accelerated by the use conditions andthe storage conditions....
Page 38 - and operate the lever quietly to prevent camera shake.
E-37 moisture and dry the Case in the shade. Do not use hot air from a hairdrier or the like and do not dry the Case under direct sunlight. Exposuret o h i g h t e m p e r a t u r e s o r d i r e c t s u n l i g h t m a y c a u s e d e f o r m a t i o n ,discoloration or breakage of the Case and det...
Page 42 - Specifications; Depth of up to 40 m; Diver's Insurance Guide
E-41 Olympus digital camera CAMEDIA C-8080 Wide Zoom Available models Dimensions E-41 Specifications ❈ We reserve the right to change the external appearance and thespecifications without notice. Pressureresistance Depth of up to 40 m Main materials Main body: Transparent polycarbonate Buckles: Stai...
