Nutone LA107WH - Manual
Nutone LA107WH – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Carillón de Puerta de Dos Tonos; INSTALACION NEUVA; INSTACIÓN DEL TRANSFORMADOR; FIGURA 1; INSTALACIÓN NUEVA O DE REEMPLAZO USANDO; NUEVA INSTALACIÓN USANDO BATERÍAS; FIGURA 4; INSTALACION DEL ALAMBRADO; CONEXIONES DE LOS ALAMABRES; INSTALACIÓN DE BATERÍA; INSTALACIÓN DE REEMPLAZO
- Page 3 – Carillon de porte à deux tons; INSTALLATION DU TRANSFORMATEUR; FIGURE 1; REMPLACEMENT OU NOUVELLE INSTALLATION SE SERVANT DU; NOUVELLE INSTALLATION À L’AIDE DE PILES; FIGURE 4; ASTUCES DE FILAGE
- Page 4 – Garantía Limitada de un Año
TO REGISTER THIS PRODUCT, VISIT WWW.NUTONE.COM
INSTALLATION INSTRUCTIONS
READ & SAVE THESE INSTRUCTIONS!
Two-Note Door Chime
• For use with either a transformer or batteries
LOCATION
TRANSFORMER:
Mount a 16-volt transformer to a conveniently located junction box.
Attic location is not recommended.
PUSHBUTTON:
The chime is designed for two-note operation. Select pushbutton
locations at front and rear (or side) doors. Do not use lighted pushbuttons with
battery-operated chime.
NEW INSTALLATION
INSTALLING TRANSFORMER
Disconnect house power until installation is complete. All wiring must comply
with local codes.
1. Use a 16 VOLT, 10 VA transformer.
2.
Refer to Figure 1.
Mount transformer to a conveniently located junction box. Do not
mount transformer in attic.
3. Use approved wire connectors to connect supply wires to transformer leads: white to
white; black to black.
FIGURE 1
FIGURE 2
FIGURE 3
SUPPLY WIRE
REPLACEMENT OR NEW INSTALLATION USING TRANSFORMER
NEW INSTALLATION USING BATTERIES
FRONT DOOR
PUSHBUTTON
FRONT DOOR PUSHBUTTON
REAR DOOR PUSHBUTTON
120vAC
TRANSFORMER 16
VOLT, 10VA
FOR ONE DOOR OR
TWO DOORS
CHIME BASE
TERMINAL BOARD
TO 120
HOUSE
WIRING
R
DO NOT OIL
C - BAT. COMMON
T - TRANSFORMER
F - FRONT DOOR PB
R - REAR DOOR PB
REAR DOOR
PUSHBUTTON
FOR ONE DOOR
OR TWO DOORS
CHIME BASE
TERMINAL BOARD
“D
”
S
IZ
E
B
A
T
T
E
R
Y
“D
”
S
IZ
E
B
A
T
T
E
R
Y
WIRES TO
CHIME
CHIME
BASE
MAKE SURE
KEYHOLE
MOUNTING HOLE IS
AT THE TOP
PUSHBUTTON
AND
TRANSFORMER
WIRING
FIGURE 4
INSTALLING THE WIRING
1. Use standard bell/chime wire (20 gauge, two-conductor).
2. Run wires as shown in Figure 2 for installation using transformer.
3. Run wires as shown in Figure 3 for installation using batteries.
MOUNTING CHIME BASE
Refer to Figure 4.
1. At chime location, cut a 1" diameter hole (for pushbutton and transformer wiring) in
the wall.
2. Pull wiring through two holes in chime base.
3. Use two provided screws to mount chime base to wall.
Make sure keyhole
mounting hole is at top.
C
F
T
“D
”
S
IZ
E
B
A
T
T
E
R
Y
“D
”
S
IZ
E
B
A
T
T
E
R
Y
R
DO NOT OIL
C - BAT. COMMON
T - TRANSFORMER
F - FRONT DOOR PB
R - REAR DOOR PB
C
F
T
WIRING CONNECTIONS
1. Use wire nuts to make connections. Insulate all connections with electrical tape.
2.
INSTALLATION USING TRANSFORMER.
Refer to Figure 2.
Connect pushbutton and transformer wires to terminal screws
marked Front, Transformer, and Rear.
3.
INSTALLATION USING BATTERIES.
Refer to Figure 3.
Connect pushbutton wires to terminal screws marked Front,
Common, and Rear.
WIRING HINTS
1. Carefully fasten wiring to wall studs and ceiling
joists. Avoid short circuits caused by staples or
clops cutting through the wiring's insulation.
2. Loop wire around terminal screws.
3. When connecting more than one wire to a
single terminal screws, twist the wires together before looping them around the
terminal screw.
4. Make sure all terminal screws are tightened securely.
BATTERY INSTALLATION
1. Install four (4) “D” size batteries as shown in Figure 4.
2. For longer life, alkaline batteries are recommended.
REPLACEMENT INSTALLATION
1. Turn off house power until installation is complete.
2. Remove cover from existing chime and disconnect wires from terminal screws. Label
all wires (Front, Transformer, Rear) as you remove them.
NOTE:
Any additional wires
(for example: common or side) should be individually capped with wire nuts or sealed
with electrical tape and pushed back into the wall cavity. These wires are not needed.
3. Remove existing chime base from wall.
4. Pull wires through holes in new chime base.
5. Use provided screws to mount base to wall.
6. Connect wires to terminal screws marked Front, Transformer, and Rear on the chime
base.
7. Place chime cover securely over the base.
8. Restore house power to chime.
Use Only Unlighted Pushbuttons
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
PARA COLOCAR ESTE PRODUCTO, VISITE WWW.NUTONE.COM INSTRUCCIONES DE INSTALACION ¡LEA Y GUARDE ESTAS INSTRUCCIONES! Carillón de Puerta de Dos Tonos • Para usar con transformador o bateríasUBICACION TRANSFORMADO: Monte un transformador de 16 voltios a una caja de conexiones conveniente. Ubicación en el...
POUR ENREGISTRER SE PRODUIT, VISITEZ WWW.NUTONE.COM INSTRUCTIONS D’INSTALLATION LIRE ET CONSERVER CES INSTRUCTIONS! Carillon de porte à deux tons • À utiliser avec un transformateur ou des piles EMPLACEMENT TRANSFORMATEUR: Installer un transformateur de 16 volts à un endroit pratique se trouvant sur...
4820 Red Bank Road, Cincinnati, Ohio 45227 Printed in U.S.A., Rev. 6/07 Part No. 99524482B Product specifications subject to change without notice. Garantía Limitada de un Año GARANTÍA DEL PROPIETARIO: NuTone garantiza al comprador consumidor original de sus productos, por el período de un (1) año d...
