Numark TT-1650 - Manual - manualsarea.com

Page 2 - SAFETY PRECAUTIONS

PAGE 1 SAFETY PRECAUTIONS Thank you for buying this Numark product.Please read these operating instructions so you will know how to operate this equipment properly.After you have finished reading these instructions, keep them for future reference. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXP...

Page 3 - TABLE OF CONTENTS

PAGE 2 TABLE OF CONTENTS IMPORTANTThe lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric s...

Page 4 - CONTROLS; General Controls

PAGE 3 CONTROLS CONTROLS General Controls 1. Power ButtonPushing this button down turns on the turntable. 2. Start/Stop ButtonsThese buttons start and stop the turntable motor. Both buttons have the same function. 3. PlatterThis turntable has a special edge design that has been optimized for "dr...

Page 5 - Tone Arm Parts

PAGE 4 CONTROLS CONTROLS continued Tone Arm Parts 7. Counter Weight and Scale RingThe Counterweight is used to balance the head shell and cartridge assembly so that the proper amount of stylus pressure is applied to the record. 8. Anti-Skate AdjustmentThis knob is used to compensate for inward track...

Page 7 - PLATTER SETUP; the front of the turntable.

PAGE 6 PLATTER SETUP 1. Locking Pins 3. ALIGNED PLATTER SETUP WARNING: Incorrect Platter setup can lead to poor turntable performance, platter instability or permanent motor damage. 1. Start by inspecting the bottom of the aluminum platter to check that both locking pins have rubber fittings on them...

Page 8 - CABLE SETUP; This turntable is shipped with two sets of special cables:

PAGE 7 CABLE SETUP CABLE SETUP This turntable is shipped with two sets of special cables: (1) Right Angle IEC Power Cord(1) Right Angle RCA cord w/ground wire NOTE: Before connecting any cables, make sure that the voltage selector switch is set to the proper setting, either 110V or 220V depending on...

Page 9 - TONE ARM SETUP; Balancing the Tone Arm

PAGE 8 TONE ARM SETUP TONE ARM SETUP A properly adjusted tone arm and cartridge setup will minimize vinyl record wear and optimize the performance of the turntable. Follow these simple steps for setting the tone arm on the turntable: Balancing the Tone Arm 1. Begin the balancing process by lifting t...

Page 10 - CARTRIDGE SETUP; For Head Shell Mounted Cartridges:

PAGE 9 CARTRIDGE SETUP CARTRIDGE SETUP For Head Shell Mounted Cartridges: The cartridge that comes with this turntable should be preinstalled on the head shell. If it isn't, please follow the below instructions for installing a cartridge onto the head shell. 1. Position the head shell and the cartri...

Page 11 - OPERATION; depending on the environment conditions.

OPERATION PAGE 10 OPERATION This turntable was designed to accommodate a variety of different mixing styles. Here are some general operation guidelines to optimize the performance of the turntable. 1. Do not place the turntable on or near a speaker or subwoofer. This may cause unwanted noise dependi...

Page 12 - WARRANTY; LIMITED PRODUCT WARRANTY

PAGE 11 WARRANTY LIMITED PRODUCT WARRANTY 1. What is covered and for how long? NUMARK INDUSTRIES LCC ("NUMARK") warrants to the original purchaser that NUMARK'S products; including but not limited to DJ mixers, amplifiers, CD players, CD Mix Stations, turntables, preamplifiers, beatkeepers, ...

Page 13 - RETURN INFORMATION; c) The faulty equipment must be packed in its original packaging.

PAGE 12 RETURN INFORMATION RETURN INFORMATION (US ONLY) a) A Return Authorization number must be obtained from Numark through the address or phone numbers below. b) A copy of the original sales receipt must also be included for the equipment to be repaired under warranty. c) The faulty equipment mus...

Page 14 - SPECIFICATIONS; speed, fully manual

PAGE 13 SPECIFICATIONS SPECIFICATIONS Turntable Section: Type: 2 speed, fully manual Motor: Direct Drive StartingTorque: > 1 Kg/cfm Platter: Aluminum Diecast Speed: 33.333 and 45 RPM Wow &Flutter: < 0.25% WRM S/N ratio: > 50dB PitchRange: +/-10% Tonearm Section: Type: Universal S-Shaped...

Page 15 - TROUBLE SHOOTING; Problem

TROUBLE SHOOTING PAGE 14 Turntable does not turn on. Disconnected Power Cord? Connect Power Cord. The sound level is very low. The Turntable is not connected to a device with a PHONO preamp. Connect the device to a preamp DJ mixer or an AV receiver that has an input labeled PHONO, not AUX or LINE. P...

Numark TT-1650 - Manual

Table of Contents:

Summary

Other Numark Models