Page 3 - FastRAD Installation Guide; Table of Contents
FastRAD Installation Guide Table of Contents Canadian & US Safety Installation Instructions i For equipment with internal power supplies i For equipment with external power supplies i Important Safety Instructions ii Canadian Regulations iii Industry Canada Notice iii US Regulations iv Federal C...
Page 4 - ii Table of Contents; Testing the FastRAD
ii Table of Contents FastRAD Installation Guide Testing the FastRAD 20 Troubleshooting 21 Programming Record 22 855601 TOC Page ii Wednesday, October 29, 1997 4:16 PM
Page 5 - FastRAD Regulations; Canadian & US Safety Installation Instructions; Please Read Carefully; For equipment with internal power supplies:
i FastRAD Regulations Canadian & US Safety Installation Instructions Please Read Carefully WARNING : To avoid electrical shock hazard to personnel or equipment damage observe the following precautions when installing telephone equipment: 1. Never install telephone wiring during a lightning storm...
Page 6 - ii; Important Safety Instructions; a. When the power supply cord or plug is damaged or frayed.
ii FastRAD Regulations Important Safety Instructions Please Read Carefully When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury of persons, including the following: 1. Read and understand all instructions . 2. F...
Page 7 - iii; Canadian Regulations; Industry Canada Notice — Please Read Carefully
iii FastRAD Regulations Canadian Regulations Industry Canada Notice — Please Read Carefully The Industry Canada label identifies Public Switched Telephone Network (PSTN) certified equipment. This certification means that the equipment meet certain telecommunications network protective, oper-ational ...
Page 8 - iv; US Regulations
iv FastRAD Regulations US Regulations Federal Communication Commission (FCC) Notice — Please Read Carefully Radio/TV Interference : This equipment, classified as a digital apparatus, generates radio frequency inter- ference and if not installed and used properly in strict accordance with the manufac...
Page 9 - US Regulations continued
v FastRAD Regulations US Regulations continued In some states, customers are permitted to install their own jacks. • The equipment may not be connected to a party line or coin /toll telephone line. Connection to Party Line Service is subject to state tariffs. (Contact the state public utility commis...
Page 10 - vi
vi FastRAD Regulations 855601 Book : 855601 FCC Page vi Wednesday, October 29, 1997 3:52 PM
Page 11 - Introduction; The Norstar; Fast Remote Access Device; is located on site near either the KSU or the PC
1 FastRAD Installation Guide Introduction The Norstar Fast Remote Access Device (FastRAD) allows a personal computer (PC) running Norstar ICS Remote Tools (ICSRT) to communicate with a Key Service Unit (KSU). FastRAD also runs with Companion Diagnostics System (CDS) and Companion Manager . The FastR...
Page 13 - Important
3 FastRAD Installation Guide Before you start ❑ Make sure you read and follow the instructions in this guide. ❑ Make sure you have the necessary tools to complete the installation. A Special parts check list is provided in this guide. ❑ Make sure all equipment in the FastRAD package is accounted for...
Page 14 - Norstar ICS Remote Tools
4 FastRAD Installation Guide Special check list To begin an installation you need: ❑ an operating Nortel two-line display telephone for programming the FastRAD ❑ a screwdriver ❑ two round head, size #8 wood screws, 1 inch long ❑ a roll of tape (or four tacks) for mounting the template ❑ a list of pr...
Page 16 - To connect the FastRAD:; : Do not connect the FastRAD to port 101. This port is
6 FastRAD Installation Guide Connecting the FastRAD When equipment and environment conditions have been veri-fied, you can begin connecting the FastRAD to the distribution block. Before you connect the FastRAD, make sure the port works. Attach a working Norstar two-line display telephone to the port...
Page 17 - : A connection to the FastRAD DB-9 pin serial port is only; TCM Port
7 FastRAD Installation Guide Figure 2 – KSU connection 6. Connect one end of the RJ-11 teladapt cord to the TCM port on the side panel of the FastRAD. See Figure 2. 7. Connect the other end to the RJ-11 teladapt jack to the KSU. Make sure the cord is less than 800 m (2600 feet) long. Note : A connec...
Page 18 - : You do not need to mount the FastRAD on the wall if it is; : This template is found at the center of this guide.; Figure 3 – Paper wall mounting template
8 FastRAD Installation Guide Mounting the FastRAD Before you mount the FastRAD, select a location within 800 m (2600 feet) of the distribution block that is free of traffic, dust and dampness. Note : You do not need to mount the FastRAD on the wall if it is only being used temporarily to program the...
Page 20 - Before you start, make sure you have completed the; FastRAD; found at the end of this guide. This; : You must program the Required fields for the FastRAD to; Table 2 – Programming parameters and default values; Programming Field; Default
10 FastRAD Installation Guide Programming the FastRAD Before you start, make sure you have completed the FastRAD Programming Record found at the end of this guide. This record must include the System ID, Auto-answer line number and Alarm reporting line number. Table 2 shows the different programming...
Page 21 - BACK; IMPORTANT; Enter password; Troubleshooting
11 FastRAD Installation Guide Starting a programming session The FastRAD cannot be used for remote or direct connections until the user password has been programed through Feature 9**. This initial password programming must occur on-site. IMPORTANT : There is no way to recover a lost or forgotten pa...
Page 22 - CHNG; OK
12 FastRAD Installation Guide 2. Press CHNG to change your programming password. Using the dialpad, enter your new password. Your pass-word must be from eight to 10 characters long. As you enter your password, the display shows asterisks. The display changes to show: Confirm password . When you re-e...
Page 23 - Starting a Programming Session
13 FastRAD Installation Guide General Programming General programming allows you to define the System ID number. Before you begin entering general programming information, make sure the display shows RAD Admin . If you do not have this display on the Norstar telephone, follow the steps in Starting a...
Page 25 - Press
15 FastRAD Installation Guide 8. Press CHNG to enter the first alarm report telephone number.The display shows: 9. Enter the telephone number for Alarm 1.The display shows: 10. Press OK . The display shows: 11. Press SHOW . The display shows: If you do not want to enter a second alarm number, press ...
Page 26 - Enter the number of minutes between retries. This must be
16 FastRAD Installation Guide 17. Press OK . The display shows: 18. Press CHNG . The display shows: 19. Enter the number of minutes between retries. This must be a number between 1 and 99. 20. Press OK . The display shows: 21. To change the baud rate, press CHNG until the desired baud rate appears. ...
Page 27 - RAD Admin
17 FastRAD Installation Guide This completes alarm programming. To continue programming FastRAD call handling, refer to the next section, Programming Data. Programming Data Data programming allows you to determine how many seconds the FastRAD waits before answering a call on an incoming KSU line. Th...
Page 28 - Choose only lines that are enabled.
18 FastRAD Installation Guide Note: In general, the following points should be consid-ered while choosing the FastRAD Auto-answer line: • If possible, use an on-core line for auto-answering. This allows remote access to the KSU even in the event of an expansion module failure. • Use a line that is n...
Page 31 - Inactive feature
21 FastRAD Installation Guide Troubleshooting Troubleshooting the FastRAD installation is needed if you start a programming session and the display shows Inactive feature . 1. Check the wiring at the distribution block. 2. Make sure the Norstar port that the FastRAD is attached to is working. 3. Che...
Page 32 - FastRAD Programming Record; GENERAL
22 FastRAD Installation Guide Programming Record Complete the FastRAD Programming Record before you start programming. FastRAD Programming Record Work Site: _______________________________________________________________ Address: ________________________ Telephone Number: __________________ ________...
