Msd 8996 Multi-Channel Digital Ignition Tester Install- User Manual
Msd 8996 Multi-Channel Digital Ignition Tester Install– User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – RPM ADjUSTMENT; never; Figure 2 Adjusting the Tester’s RPM.; Figure 3 Testing an MSD Triggered with Points or an Amplifier.
- Page 3 – Figure 4 Testing an MSD 6 Series Through the Magnetic Pickup.; Figure 5 Testing an MSD 7 Series Through the Magnetic Pickup.
- Page 4 – Figure 6 Testing an MSD with Timing Accessory.; Figure 7 Testing an MSD Programmable 7 Series Inition.
- Page 5 – TESTING DIS IGNITIONS; Do not connect directly to the coils or this unit will be damaged.
- Page 6 – • Check for 12 volts on the Tester's Red wire.; TECH NOTES
- Page 8 – M S D I G N I T I O N; Limited Warranty; for special or consequential damages.; Service; When returning MSD components for warranty service,; Proof of Purchase; must be supplied for verification. After
M S D I G N I T I O N
• w w w . m s d i g n i t i o n . c o m • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4
PROGRAM SELECTION
PROGRAMS
8 Cylinder
8 Cyl-DIS
6 Cylinder
6 Cyl-DIS
6 Cyl-Odd
4 Cylinder
4 Cyl-DIS
Multi-Channel MSD Ignition Tester
PN 8996
These instructions detail how to use the Multi-Channel tester with an MSD 6, 7, 8, 10, Digital 7 Series Ignition
Control or Multi-function Controllers. If you need to test an MSD DIS Ignition, see pages 5 and 6.
WARNING:
Do not connect directly to the coil or this unit will be damaged.
PARTS INCLUDED:
1 - Digital Ignition Tester
PROGRAMMING
The MSD Multi-Channel Ignition Tester
has the ability to test several different
combinations of ignition setups. By
pushing the Red button on the face
of the unit different programs can be
selected. Figure 1 shows the different
applications.
When you first connect power to the
Tester, the LED will display the name
and Part Number. You can bypass this
information by pushing the Red button.
The Tester automatically defaults to the program for an 8-cylinder, single trigger ignition system. To select
a different program just press the Red Select button until the program you need is displayed.
Note:
If you have an MSD DIS Ignition Control, two test harnesses are offered to make testing each
channel of the ignition easier. The DIS-4 Test Harness is PN 89964, the DIS-2 is PN 89962. These
Harnesses will allow you to test the ignition and coils without having to splice into any wires. Figure
9 shows the harness.
WIRING
The Digital Tester has several wires with boots and alligator clips on each one. The wires with White
boots are all trigger wires. Note: All of the wires are only used when testing a DIS-4 Ignition Control.
Red:
Connect to 12 volts.
Black:
Connect to a good ground source.
White:
This is the trigger wire used to test the points/amplifier (white wire trigger) circuit of an
MSD Ignition. When testing DIS Ignitions, this is the Channel 1 trigger.
Green:
Channel 2 for a DIS Ignition.
Yellow:
Channel 3 for a DIS Ignition.
Violet:
Channel 4 for a DIS Ignition.
Green/Violet:
This 2-Pin connector is for testing the magnetic input circuit for MSD Ignitions. It plugs
directly into the MSD’s magnetic pickup connector. Violet is mag + and Green is mag -.
Lt. Blue/
This is a 2-pin connector for testing the cam sync pickup circuit of an MSD Programmable
Ignition or Multi-Function Controller. It plugs directly into the MSD Digital 7 Programmable
Ignition's cam pickup connector. Lt. Blue is cam (+) and Lt. Green is cam (-). The CPC
Ignition is supplied with a harness adapter.
Figure 1 Ignition Tester Programs.
1 - Spark Tester
Lt. Green:
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
INSTALLATION INSTRUCTIONS M S D I G N I T I O N • w w w . m s d i g n i t i o n . c o m • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 RPM ADjUSTMENT The MSD Digital Tester has two rpm adjustments; Coarse and Fine: Coarse Adjustment: When this knob is turned clockwise the rpm will inc...
INSTALLATION INSTRUCTIONS M S D I G N I T I O N • w w w . m s d i g n i t i o n . c o m • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 Figure 4 Testing an MSD 6 Series Through the Magnetic Pickup. CAM SYNC PICKUP OUTPUT NOT USED Figure 5 Testing an MSD 7 Series Through the Magnetic Pi...
INSTALLATION INSTRUCTIONS M S D I G N I T I O N • w w w . m s d i g n i t i o n . c o m • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 Figure 6 Testing an MSD with Timing Accessory. CAM SYNC PICKUP OUTPUT NOT USED Figure 7 Testing an MSD Programmable 7 Series Inition. DIS TRIGGERS NOT...
