Msd 8886 Adapter Cable for MSD 6010_60101 to GM OEM Se- User Manual
Msd 8886 Adapter Cable for MSD 6010_60101 to GM OEM Se– User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – MAP sensor; Cam Connector of the 6LS to the connector with a single signal wire.; Figure 2 Map Sensor Connection.; TIMING
- Page 3 – CrAnkshAft sensor; Figure 4 Crankshaft Sensor Location.; CRANK; Figure 6 Connecting the Crank Sensor.
- Page 4 – NOTES; limited Warranty; for special or consequential damages.; service; When returning MSD components for warranty service,; Proof of Purchase; must be supplied for verification. After; M S D I G N I T I O N
6LS Harness for EFI Vehicles
PN 8886
Parts Included:
2 - Cam/Crank Sensor Harnesses
1 - Map Sensor Harness
2 - Coil Simulators
2 - Coil Simulator Clips
This Harness Kit allows the installation of the MSD 6LS Ignition Controller on Gen III LS-1 and LS-6
based engine vehicles equipped with factory EFI systems. The Harness connects inline to factory
sensors and provides the 12 volt supply and ground of the Controller. It can also be used on early
Gen IV LS-2 based engines, when combined with Cam Sensor Extension Harness PN 88861.
Coil ConneCtions
Note:
One of the Coil Simulators has a 3-Pin pigtail. This assembly connects to the passenger side
coil bank.
Disconnect the factory connector from the coil
harness (Figure 1). Connect the MSD Coil Simulators
inline with the factory harness. Use the supplied clips
to secure the Simulators.
IMPORTANT:
Read instuctions thoroughly before attempting installation.
1 - Crank Sensor Tool Body
1 - Crank Sensor Tool Blade
2 - 6-32 x .250 Screws
WARNING:
Before installing the 6LS Harness, disconnect the battery cables. When disconnecting
the battery cables, always remove the Negative (-) cable first and install it last.
Figure 1 Coil Connections.
TO MSD
6LS
FROM
MSD
6LS
FACTORY
HARNESS
TO PN 8886
M S D I G N I T I O N
• w w w . m s d i g n i t i o n . c o m • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
INSTALLATION INSTRUCTIONS M S D I G N I T I O N • w w w . m s d i g n i t i o n . c o m • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 MAP sensor Disconnect the MAP sensor harness and install the MSD Harness inline. The Gray Connector of the Harness goes to the MAP sensor. Connect the...
INSTALLATION INSTRUCTIONS M S D I G N I T I O N • w w w . m s d i g n i t i o n . c o m • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 CrAnkshAft sensor This sensor is located just above/behind the starter. If the engine is in the car, you will need to assemble the supplied special to...
NOTES limited Warranty M SD IGNITION warrants this product to be free from defects in material and workmanship under its intended normal use*, when properly installed and purchased from an authorized MSD dealer, for a period of one year from the date of the original purchase. This warranty is void f...
