Msd 8488 Pro-Billet Honda Distributor, 92-95 Installat- User Manual
Msd 8488 Pro-Billet Honda Distributor, 92-95 Installat– User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Figure 3 Wiring the Coil and Driver to the Distributor.; INSTALLATION; OFFSET
- Page 3 – Figure 4 Wiring the Coil and Driver with an MSD CD Ignition Control.; WIRING AN MSD IGNITION CONTROL; Note: It is normal for the conductor to retract into the insulation; Figure 5 Stripping the Sleeve.
- Page 4 – Limited Warranty; or consequential damages.; Service; When returning MSD components for warranty service,; Proof of Purchase must be supplied for verification. After; All returns must have a Return Material Authorization (RMA) number; issued to them before; M S D
IMPORTANT: Read the instructions before attempting the installation.
Parts Included:
1 - Honda Distributor
1 - Parts Bag
1 - Wire Retainer
5 - 90° Boots and Terminals
WARNING: During installation, disconnect the battery cables. When disconnecting the battery,
always remove the Negative cable first and install it last.
WARNING: The Blaster SC Coil and Coil Driver produce very high voltage and current. Use
caution during installation and while working near the Coil assembly.
Note: The MSD Distributor Cap requires spark plug style 90° terminals and boots, which are supplied.
MSD also offers complete wire sets with the correct terminals and lengths. For more informa-
tion, contact MSD or go to www.msdignition.com.
The MSD Pro-Billet Honda Distributor
must be used with the SC Coil Driver, PN 6305, and Blaster SC
Coil, PN 8235. An MSD SCI, 6-Series and 7-Series Ignition Control may be used, but not required.
REMOVAL
IMPORTANT: C h e c k a n d e s t a b l i s h
the ignition timing prior
to removing the original
distributor.
1. Clean the area around the distributor
and the engine to remove any loose
debris. Disconnect the distributor
connector.
2. Mark the location of each spark plug
wire, then remove the wires from the
distributor (Figure 1).
3. Remove the three 12mm bolts that
secure the distributor to the engine.
Remove the distributor by pulling it
straight out of the engine.
Figure 1 Removing the Wires and Factory Distributor.
DISTRIBUTOR
CONNECTOR
2
3
4
1
2
3
4
1 - Mini-Stripper-Crimper Tool
Components Required:
1 - SC Coil Driver, PN 6305
1 - Blaster SC Coil, PN 8235
MSD Pro-Billet Honda Distributor
PN 8488
M S D
• W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4
ONLINE PRODUCT REGISTRATION: Register your MSD product online and you’ll be entered
in our monthly 8.5mm Super Conductor Spark Plug Wire give-away! Registering your product
will help if there is ever a warranty issue with your product and helps the MSD R&D team create
new products that you ask for! Go to www.msdperformance.com/registration.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 INSTALLATION INSTRUCTIONS M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 Figure 3 Wiring the Coil and Driver to the Distributor. Figure 2 Aligning the Distributor and Camshaft. INSTALLATION 1. Apply a film of oil ...
INSTALLATION INSTRUCTIONS 3 M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 Figure 4 Wiring the Coil and Driver with an MSD CD Ignition Control. WIRING AN MSD IGNITION CONTROL An MSD Ignition Control is not required ...
Figure 8 Preparing to Crimp in the Vise. Figure 9 Crimping with the Vise. Figure 7 Aligning the Terminal in Tool. Limited Warranty M SD warrants this product to be free from defects in material and workmanship under its intended normal use*, when properly installed and purchased from an authorized M...
