Msd 7330 7AL-3 Ignition Control Installation- User Manual
Msd 7330 7AL-3 Ignition Control Installation– User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – WIRING; PRIMARY WIRING; Magnetic Pickup Polarity; Common Mag Pickup Wires; Distributor; Figure 1
- Page 4 – Figure 5 Primary Wiring to a Mallory Unilite Distributor.
- Page 5 – GM HEI DISTRIBUTOR
- Page 6 – OPTIONAL WIRING; START RETARD; Off; THREE STEP RPM LIMITS; Figure 9 Wiring the Start Retard Function.; Figure 10 Connecting the Three Step Module Selector.; Figure 8 Side View of 7 AL-3
- Page 7 – RPM ACTIVATED SWITCH; must; Figure 11 Connecting the RPM Activated Switch.
- Page 8 – GROUND
- Page 9 – of 20° even if the modules add up to more than 20°.; RETARD WITH THE RPM ACTIVATED SWITCH; only activate a circuit by; Note: Make sure 12 volts is applied to the RAS On/Off terminal.; Figure 15 Activating the RAS in High Gear Only.
- Page 10 – KILL SWITCH; TROUBLESHOOTING; TRIGGER LED; Figure 17 Connecting a Kill Switch to Points.; Figure 18 Connecting the Kill Switch to the Mag+.; TACHOMETER
- Page 11 – WIRING CHECK
- Page 12 – Limited Warranty; or consequential damages.; Service; When returning MSD components for warranty service,; Proof of Purchase must be supplied for verification. After; All returns must have a Return Material Authorization (RMA) number; issued to them before; M S D; RETARD MODULE SELECTORS
M S D
• W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4
MSD 7AL-3, Ignition Control
PN 7330
Important: Read the instructions before attempting the installation.
Parts Included:
1 - 7AL-3, PN 7330
1 - Parts Bag (wires and connectors)
4 - RPM Modules 3000, 7000, 8000, 9000
4 - Retard Modules
2°, 3°, 4°, 5°, 10°, 15° and 20°
4 - Zero Degree Modules
4 - Vibration Mounts
WARNING: During installation, disconnect the battery cables. When disconnecting the battery,
always remove the Negative cable first and install it last.
Note: The MSD 7AL-3 will retard the ignition timing approximately 4° compared to other MSD Ignitions.
After installation, the timing should always be checked and adjusted at idle and total timing.
COIL RECOMMENDATIONS
The MSD 7AL-3 can be used with a variety of coils, but to receive the best performance, it is
recommended to use an MSD Coil. For drag racing and “short duration” applications, the Pro Power
Coil, PN 8201. For street applications or long duration racing events, the HVC Pro Power Coil, PN
8251 or PN 8261 are recommended. The 7AL-3 may be used with a GM HEI Distributor with an internal
coil, however the Rotor Bushing
must be replaced with an MSD Low Resistance Bushing, PN 8412.
MOUNTING
The 7AL-3 can be mounted under the hood, but should be mounted in a position away from direct
engine heat sources. Use the ignition as a template and mark the location of the mounting holes.
Remove the unit and drill the holes using a 1/4" bit. Install the vibration mounts to the 7AL-3 then
mount the ignition using the supplied lock washers
and nuts.
CYLINDER SELECT
This ignition can be used on 4, 6 (even-fire) or
8-cylinder engines. The ignition is set for 8-cylinder
operation. To program the unit for other engines,
remove the one screw that holds the cover to reveal
three wire loops (Figure 1). Cutting a wire loop
determines the cylinder selection.
ONLINE PRODUCT REGISTRATION: Register your MSD product online. Registering your
product will help if there is ever a warranty issue with your product and helps the MSD R&D
team create new products that you ask for! Go to www.msdperformance.com/registration.
Cylinders Loops to Cut
8
None
6
One
4
Two
Cut loops
Remove cap
Figure 1 Cylinder Programming.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 IN S T A L L A T I O N I N S T R U C T I O N S M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 WIRING Wiring the 7AL-3 will be simple by following the instructions. There are several color coded wires supplied with...
4 IN S T A L L A T I O N I N S T R U C T I O N S M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 Note: The MSD 7AL-3 will retard the ignition timing approximately 4° compared to other MSD Ignitions. After installatio...
IN S T A L L A T I O N I N S T R U C T I O N S 5 M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 RAS ON/OFF Figure 7 Primary Wiring to a GM HEI with a 5 or 7-Pin Module (Points Trigger). Figure 6 Primary Wiring to a ...
