Milwaukee 4297-1 - User Manual
Milwaukee 4297-1 – User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
135
Select one of these 4 MILWAUKEE motors for your No. 4202 or No. 4203 Electromagnetic Drill Stand.
These motors include reverse for compatibility with the Electromagnetic Drill Stand control panel.
4203
BASE ONLY
•
ADJUSTABLE
POSITION,
•
11" DRILL
TRAVEL
4202
BASE ONLY
•
FIXED POSITION,
•
9" DRILL TRAVEL
4253-1
4262-1
4292-1
4297-1
•
600 NO LOAD RPM
•
350 NO LOAD RPM
•
TWO SPEED
•
TWO SPEED
•
750/375
•
500/250
NO LOAD RPM
NO LOAD RPM
CHUCK CENTER DISTANCE FROM BASE
MOTOR NO. 4253-1
IN
OUT
Magnetic Stand 4202
1-1/4"
*
Plate Forward
4203
1-23/32"
*
Plate Back
4203
31/32"
*
MOTOR NO. 4262-1
IN
OUT
Magnetic Stand 4202
1-23/32"
4-11/16"
Plate Forward
4203
2-1/8"
5-3/32"
Plate Back
4203
1-3/8"
4-11/32"
MOTOR NO. 4292-1
IN
OUT
Magnetic Stand 4202
2-3/16"
4-3/8"
Plate Forward
4203
2-9/16"
4-11/16"
Plate Back
4203
1-13/16"
3-15/16"
MOTOR NO. 4297-1
IN
OUT
Magnetic Stand 4202
2-3/16"
4-3/8"
Plate Forward
4203
2-9/16"
4-11/16"
Plate Back
4203
1-13/16"
3-15/16"
IN
= Closest to base
OUT
= Farthest away from base
*
Motor 4253-1 has only one chuck position.
Stand 4203 is adjustable 3/4" in direction of base length and
20° right or left.
All models furnished with 6 ft. safety chain.
■
Base Control Panel Includes Variable
Speed Adjusting For Motor
■
Solid State Electronic Switching
■
Feedback Speed Control
■
Computer Controlled Reverse
■
Full Wave Magnetic Holding Power
■
Forward/Reverse Control
■
Superior Cutting Tool Performance
■
Line Lock-Out
Prevents tool from operating should voltage
be restored to an interrupted line when
switch is locked in the "on" position.
■
Motor/Magnet Interlock
■
Automatic Base/Chip De-Mag
■
Automatic Electronic Soft Start
■
For Use On Any Flat Ferrous Material 1/2"
And Thicker
SPECIFICATIONS
*
DRILL
REPLACEMENT
REPLACEMENT
VOLTS
NO
POINT
CHUCK
CHUCK
CHUCK KEY
CATALOG
AC LOAD
PRESSURE
OR
CATALOG
CATALOG
WEIGHT
NUMBER
ONLY
AMPS
RPM
DRILL
▲
TAP
LBS.
TAPER
NUMBER
NUMBER
LBS.
4253-1
●
120
6.2
600
1/2"
5/8"-18
†
1610/1650
Chuck
48-66-1360
48-66-3280
8.0
4262-1
120
11.5
350
3/4"
1"-14
1630/1670
Chuck
48-66-2085
48-66-3160
21.0
4292-1
120
11.5
750/375
1-1/4"
1"-14
1530/1600
No. 3MT
45-34-0110
#3 Taper Socket
23.0
4297-1
120
11.5
500/250
1-1/4"
1"-14
1530/1600
No. 3MT
45-34-0110
#3 Taper Socket
23.0
●
Drills except No. 4253-1 have dual mount gear case permitting reverse mounting of drill for close quarter work.
†
5/8"-11 or 1/2"-13 taps not recommended.
▲
NOTE... To adapt a 3/4" capacity chuck to 1-1/4" Drills with No. 3 internal Morse Taper Socket specify Chuck and Arbor Kit No. 49-22-1550, which consists of Chuck No. 48-66-2000 and Arbor No.
48-07-0100. Extend chuck capacity to full drill capacity by using 1/2" reduced Shank Twist Drills shown in the MILWAUKEE catalog.
*
Drill point pressure on a 1" thick steel plate with the chuck mounted closest to the base. Values listed are for the drill motor mounted on a No. 4202 base/No. 4203 base that is adjusted to the rearward position.
CAT.
WGT.
NO.
HEIGHT
WIDTH
LENGTH
LBS.
4202
15"
4-1/4"
11"
41.0
4203
17-1/4"
4-1/4"
11"
49.0
SPECIFICATIONS
DRILL STAND SPECS
CAPACITY
HEAVY-DUTY
ELECTROMAGNETIC DRILL
MOTORS AND BASES
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
