Miele T 9802 - Manual

a Program buttons To select a drying program b Options buttons Special features to enhance a dryingprogram c Check Filter/Vent indicator Indicates to clean the filter or vent d Status indicator Shows the current cycle of the dryingprogram e Start/Stop button Starts and stops a program, or ifpressed ...

Clean the drum interior before thefirst use. Fabric care labels Before drying, check fabric care labelsfor special drying instructions. q = Drying with a normal temperature r = Drying with a low temperature s = Do not dry in a tumble dryer Drying tips – Observe the maximum loads, see the "Progra...

1. Sort the laundry ^ Sort the laundry by desired dryness,fabric, size and similar residualmoisture after spinning to assureeven drying results. , Do not dry items that may melt or ignite in the dryer such as plastics orrubber. They could melt anddamage the laundry. ^ Check hems and seams, so that n...

4. Select an option ^ Press any button. The combination "Turbo/Gentle" is notpossible. Turbo Heat resistant items (with fabric caresymbol q ) will be dried at a high temperature. – Laundry will be dried faster. Gentle Items sensitive to high temperatures(with fabric care symbol r ) will be d...

5. Start the program During the program selection the"Start/Stop" indicator flashes meaningthat the program can be started. ^ Press the "Start/Stop" button. The "Start/Stop" indicator lights. The "Status" indicator of the reacheddrying degree lights. Before the end of...

Extra Dry Items Multi-layered, mixed loads of sturdy cottons, e.g. towels, bath robes. Note The "Extra dry" program should not be selected for jersey materials.Items may shrink. Options Turbo or Gentle, Buzzer Normal Items Single and multilayered cotton and linen laundry e.g. terry towels,be...

Cleaning the lint filter The lint is collected by the lint filter inthe door. The lint filter must be cleanedafter every program. ^ Clean the lint filter whenever the"Check Filter/Vent" indicator comeson. ^ Pull out the lint filter. ^ Wipe the lint off the filter with yourhand (do not use an...

Cleaning the exterior and thecontrol panel , To reduce the risk of electric shock, disconnect the dryer from thepower supply by shutting off thepower main, tripping the circuitbreaker or unplugging the powercord before performingmaintenance.Never use abrasive cleaners,scouring pads, steel wool or ca...

Changing the light bulb To reduce the risk of electric shock,disconnect the appliance from thepower supply by unplugging ortripping the circuit breaker. ^ Open the door. The lighting is in the drum opening inthe upper right-hand corner. ^ Remove the screw. ^ Flip the cover down. ^ Replace the light ...

, Repairs to electrical appliances must only be carried out by a qualified and trained person in accordance with local and national safety regulations.Repairs and other work by unqualified persons could be dangerous. The following section will help you avoid placing a service call by identifyingissu...

Quick Guide Remove this guide for easyreference To prevent accidentsand appliance damageread these instructions before installation or use.

1. Prepare and sort the laundry ^ Check for damages and foreignobjects. ^ Close zippers, hooks and eyelets. ^ Tie up belts and apron ties. 2. Load the laundry ^ Open the door. Without the laundry basket ^ Load the laundry loosely in the drum. , To prevent fabric damage, check that laundry will not b...

3. Select a program ^ Press the desired program button. 4. Select an option ^ Select an option button, if desired. The combination "Turbo/Gentle" is notpossible. 5. Starting a program ^ Press the "Start/Stop" button. 6. Program end - Unload the laundry The "End" indicator lig...

Short program guide Extra Dry Multi-layer, mixed loads of sturdycottons, e.g. towels, bath robes. The "Extra dry" program should not beselected for jersey materials. Itemsmay shrink. Options: Turbo or Gentle, Buzzer Normal Single and multilayered cotton andlinen laundry e.g. terry towels, be...

Fault indicators The "Check Filter/Vent" indicator lights. Possible fault Solution The dryer does not workat its optimum or notefficiently. The lint filtermight be clogged withlint or detergentresidues. – Usually cleaning the lint filter fixes the problem. If the problem persists, check all ...

Repairs In the event of a fault which you cannotfix yourself, please contact the servicenumber on the back of this manual. When contacting Technical Service,please quote the model and serialnumber of your appliance. These canbe found on the data plate. Optional accessories Optional accessories can b...

Installation Instructions Information is subject to change. Please refer to our website to obtain the mostcurrent product specification, technical & warranty information. To prevent accidentsand appliance damageread these instructions before installation or use.

, WARNING - Risk of Fire ~ To reduce the risk of severe injury or death, follow all installation instructions. ~ Clothes dryer installation must be performed by a qualified installer. ~ Install the clothes dryer according to the manufacturer's instructions andlocal codes. ~ Repair and maintenance wo...

Front view a Exhaust connection b Power cord with plug c Control panel d Door e Four height adjustable screw feet Stand A dryer stand, with drawer, can bepurchased as an optional accessory. Installation 28

Transporting the dryer to theinstallation site The rear excess end of the lid has ahandle for transport. ^ Use the front dryer feet and the rearexcess end to transport the dryerfrom the packaging base to theinstallation site. Level the dryer The dryer must be level to ensure safeand proper operation...

Electrical connection GROUNDING INSTRUCTIONSThis appliance must be grounded.In the event of malfunction orbreakdown, grounding will reducethe risk of electric shock byproviding a path of least resistancefor electric current. This appliance isequipped with a cord having anequipment grounding conducto...

Installation tips An airflow gap of 3 / 8 " (10 mm) must be provided between the applianceand the floor. This airflow gap mustnot be blocked by a toe-kick or thickpiled carpets. Sufficient venting of the installationsite, e.g. by opening a window ordoor, is essential for the dryer'soperation. Ot...

Tips about the ductwork – Check with your local building code to determine the maximum allowableduct length. – Only use rigid or flexible metal duct for exhausting. Non-metallic flexiblehose should not be used, it is apotential fire hazard. – Rigid metal or flexible aluminum ducting is preferred. Fl...

Direct wall connection Necessary materials: – a wall pipe – flexible foam gasket Dryer top view 1 Wall pipe 2 Flexible foam gasket Dryer side view 1 Wall pipe 2 Flexible foam gasket ^ Connect the flexible foam gasket, 2 , to the wall pipe connector, 1 . ^ Push the dryer to the wall. Installation 38

Disposal of the packingmaterials The packing materials protect theappliance during shipping. They havebeen designed to be biodegradableand recyclable. To prevent suffocation, ensure that anyplastic wrappings, bags, etc. aredisposed of safely and kept out of thereach of children. Disposal of an appli...