Page 3 - Table of Contents; Appendix A
iii Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Unpacking List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Scanner Installation . . . . . . . . . . . . . . ....
Page 4 - The shipping carton, should contain the following:
1 Introduction Metrologic’s TECH 7 laser bar code projection scanner is encased in anNEMA-12 steel case. The case construction enables the scanner to operate inharsh surroundings, especially industrial environments. Water-resistant,shock-resistant, and rugged, the TECH 7 is also fast, aggressive and...
Page 5 - Scanner Installation
2 Scanner Installation To maintain compliance with applicable standards, all circuits connected to thescanner must meet the requirements for SELV (Safety Extra Low Voltage)according to EN 60950. To avoid potential problems, do not power up thescanner until the communication cable is secured to the h...
Page 6 - Configuration to the Host System
3 Configuration to the Host System The scanner is shipped from the factory programmed to a set of defaultconditions noted in the ScanSelect Scanner Programming Guide by an asteriskthat appears before the brief definition located next to the bar code. In order for the scanner to communicate with a ho...
Page 7 - Stand Installation; To fasten the scanner:
Base of Stand 4 Figure 1 Figure 2 Figure 3 Stand Installation With the Metrologic stand (Part#45475), the scanner can bepositioned in one of two directions.The two orientation choices arevertical or horizontal. (Refer toFigure 1) To install this stand, use the four 6-32 x ½ inch machine screws and t...
Page 8 - Back Plate Installation; To fasten the scanner to the back plate:
5 Figure 4 Figure 5 Back Plate Installation With the Metrologic back plate(Part #45473), position the scanner in one of two directions. The twoorientation choices are vertical orhorizontal. (Refer to Figure 4). Touse this stand, use the four 6-32 x ½inch machine screws and four woodscrews to attach ...
Page 9 - Parts of the Scanner; Green and Red LEDs; This aperture emits the laser light.; Mil spec Connector
Laser Output Window Speaker Mil spec Connector Green and Red LEDs 1 2 3 4 6 Figure 6 Parts of the Scanner 1 Green and Red LEDs When the green LED is on, thisindicates that the unit is receivingpower and the laser is on. When thered LED flashes on, the scanner hasread a bar code successfully. When th...
Page 10 - Visual Indicators; This indicates the scanner is in program mode.
7 Visual Indicators There is a red and green LED at the top of the scanner. When the scanner ison, the flashing or stationary activity of the LEDs indicates the status of thescan and scanner. Steady Green When the laser is on, the green LED is also on. This occurs when an object isin the scan field....
Page 11 - Signaux optiques
8 Signaux optiques Sur la partie supérieure du scanner se trouvent une diode LED rouge et une diode LEDverte. Quand le scanner est sous tension, les diodes rouge et verte clignotantes ouallumées vous informent sur l'état du scanner. Ni la diode rouge, ni la diode verte n'est allumée Il existe deux r...
Page 12 - Optische Anzeigen
9 Optische Anzeigen Auf dem Scanner befinden sich eine rote und eine grüne Leuchtdiode. Beieingeschaltetem Scanner geben Ihnen die blinkenden bzw. feststehendenLeuchtdiodenanzeigen Aufschluß über den Abtast- und Scannerstatus. Weder rote noch grüne Leuchtdiodenanzeige Es gibt zwei mögliche Gründe, w...
Page 13 - Segnali ottici
10 Segnali ottici Sullo scanner si trovano due diodi luminosi: uno rosso e uno verde. Quando lo scannerè inserito, i diodi luminosi, che possono o essere accesi in continuazione o lampeggiare,Vi informano sullo stato della scansione e dell’apparecchio. Né il diodo luminoso rosso né quello verde sono...
Page 14 - Labels
11 Labels There is one label located inside the window of the scanner noting that thisdevice is a CDRH Class IIa laser product and IEC 825 LASERKLASSE 1.Also, on the scanner is a label located on the back of the unit. This labelcontains information such as the model number, date of manufacture, seri...
Page 15 - Depth of Scan Field for the MS770 Scanner
12 Figure 7 Depth of Scan Field for the MS770 Scanner The depth of field for the scanner is 76mm to 254mm (3" - 10") from the laseroutput window. Pass the symbol through the scan area in order for the scannerto recognize the bar code. (Refer to Figure 7)
Page 16 - Depth of Scan Field for the MS775 Scanner
13 Figure 8 Depth of Scan Field for the MS775 Scanner The depth of field for the scanner is 76mm to 254mm (3" - 10") from the laseroutput window. Pass the symbol through the scan area in order for the scannerto recognize the bar code. (Refer to Figure 8)
Page 17 - Maintenance; Spray glass cleaner onto lint free, nonabrasive cleaning cloth.; Applications and Protocols; Version Identifier; Light Pen Emulation
14 Maintenance Smudges and dirt can interfere with the proper scanning of a bar code.Therefore, the output window will need occasional cleaning. 1. Spray glass cleaner onto lint free, nonabrasive cleaning cloth. 2. Gently wipe the output window. Applications and Protocols The model number on each sc...
Page 18 - Specifications; Mechanical
15 Appendix A Specifications Application: Industrial Projection Scanner Light Source: Visible Laser Diode 670 ± 5nm, Laser Class: CDRH: CLASS IIa; EN 60825 Class 1 Certifications: CE, UL listed for US and Canada EMC: FCC Class A, CISPR Class A Mechanical Dimensions: 184mmL x 186mmW x 78mmD(7.25"...
Page 20 - Appendix B; Pin Assignments; Pin
17 Figure 9 Appendix B Pin Assignments Version “1” Pin Assignments for RS-232, OCIA, and BidirectionalRS-232 Each TECH 7 scanner has a 19-pin male Mil spec connector that is located onthe side of the unit. To connect the scanner to the host device, use acommunication cable with a female Mil spec con...
Page 22 - Appendix C; Warranty and Disclaimer; Limited Warranty
19 Appendix C Warranty and Disclaimer Limited Warranty Products manufactured by Metrologic have a 2-year limited warranty fromdate of manufacture. This warranty is limited to repair, replacement or refund at Metrologic’sdiscretion. Faulty equipment must be returned to the Metrologic facility inBlack...
Page 24 - Appendix D; Notices
21 Appendix D Notices Notice This equipment has been tested and found to comply with limits for a Class A digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference when the equipment is operated in a commercial environ...
Page 26 - Appendix E; Patents; “Patent Information
23 Appendix E Patents “Patent Information This METROLOGIC product may be covered by one or more of the followingU.S. Patents: U.S. Patent No. 4,360,798; 4,369,361; 4,387,297; 4,460,120; 4,496,831;4,593,186; 4,607,156; 4,673,805; 4,736,095; 4,758,717; 4,816,660; 4,845,350; 4,896,026; 4,923,281; 4,933...
Page 27 - Index
24 Index A AC 2, 15 Application 15Application and protocols 14Asia ii ASIC 1 B Back plate hortizontal mount 5vertical mount 5 Bar code(s) 1, 3, 6, 7, 12-14Beep 2, 3, 6, 7, 10, 16 Beeper operation 16 C Cable communication 1, 2, 6, 17, 18 length 15 CDRH class IIa 11Clean 14, 16 Communication protocol ...
