Page 2 - Danger of suffocation due to packing material
Safety instructions and warnings • To prevent injury or damage to the unit, the ap - pliance should be unpacked and set up by two people. • In the event that the appliance is damaged on delivery, contact the supplier immediately before connecting to the mains. • To guarantee safe operation, ensure t...
Page 3 - Description of the appliance; bm; Never cover this grille or otherwise obstruct; Temperature and control display; touch capacitance
Description of the appliance 1 Operating and control elements 2 Adjustable door racks 3 Adjustable storage shelves 4 Bottle racks 5 Type plate (behind the vegetable drawer on the left-hand side) 6 Vegetable drawers 7 Water filter 8 Upper freezer drawer 9 Lower freezer drawer bl IceMaker (in the inte...
Page 4 - Setup mode; To avoid the risk of bacteria growth, the water filter; Water filter; The appliance is suitable solely for cooling food in; The appliance is not intended for com-
Replace the filter when the waterdrop symbol appears in the temperature display. Filters can be obtained from your dealer.The drop symbol must be cancelled after the filter has been changed. For detailed instructions see section entitled " Setup mode ". Water filter Before switching on the a...
Page 5 - Setting the temperature; To reduce the temperature:; Installing the water filter; Partition for bottom freezer drawer
EN Switching the appliance on and off You are advised to clean the appliance before switching it on for the first time (see "Cleaning" ). Do not load with frozen food until the temperature shows at least -18°C. The refrigerator and freezer compartments can be oper - ated separately. Switchin...
Page 6 - SuperCool
Power failure/FrostControl display If the LED comes on on the control panel, this means that the freezer temperature has risen too high during the last few hours or days due to a power failure. If you touch the ALARM icon now, the highest temperature registered during the power failure will be displ...
Page 7 - Confirm water filter change; Child lock
EN = Confirm water filter change After the water filter has been changed, the drop symbol on the display must be reset. Resetting the drop symbol • Activate setup mode by touching the SuperFrost icon for 5 seconds. • Touch the freezer compartment Down icon until appears in the display. • Touch the S...
Page 8 - Lower hinge heating control; Changing the heating output; Display brightness; Adjusting the display brightness; = Ice maker vacation state; Adjusting the water quantity; = Set BioFresh temperature; Setting the BioFresh temperature
= Lower hinge heating control If condensed water appears in the lower hinge area or on the base plate between refrigerator and freezer compartment, increase the output of the heating lo - cated behind the base plate. The factory setting is set to = me- dium output. Changing the heating output • Acti...
Page 9 - Equipment; bottle holder; Confirm dust filter cleaning; SuperFrost; Down
EN Removing the BioFresh drawer Pull the drawer straight out, grip at the back and lift out. Inserting the BioFresh drawer Place the drawer on the pull- out rails. The rails must be fully extended and aligned with the front of the drawer. Slide the drawer in. Repositioning the shelves 1. Hold the sh...
Page 10 - Arranging food; Note; Interior light
Arranging food (1) butter, cheese (2) eggs (3) bottles (4) frozen food, ice cubes (5) meat, sausage products, dairy products (6) baked goods, pre-cooked meals (7) fruit, vegetables, salads (for high humidity setting) meat, cold meats, dairy products (for low humidity setting) The adjustable humidity...
Page 11 - Freezing; Freezer compartment description; Notes; Dry; Humidity selection; Humid; Freezing with SuperFrost; off automatically; You should not switch on the SuperFrost func tion:
Freezing Fresh food should be frozen to the core as rapidly as possible. Frozen food can also be given a cold boost. This is provided by the SuperFrost facility. Space for freezing and storage Ice maker Ice cube bin Freezer compartment description Both drawers can be used for freezing of food or sto...
Page 13 - Activating the ice maker vacation state; Ice maker vacation state
Switching the ice maker on • Touch the IceMaker icon so that the IceMaker LED comes on. After you start the ice maker for the first time, it may take up to 24 hours before the first ice cubes are ready. The production capacity depends on the temperature inside the freezer compartment. The lower the ...
Page 14 - Setup Mode; Cleaning the air filter; Before cleaning always switch off the appliance. Pull out; Do not use steam cleaners because of the; Refrigerator compartment
• Open the bottom freezer drawer and remove the ventilation grille by pull - ing forwards. The grille is supported magnetically so no tool is required for removing. • Reset the air filter LED. Refer to chapter Setup Mode - = Reset air filter LED. • Push down the button of the air filter, tilt to the...
Page 15 - Malfunctions; You may be able to rectify the following faults by checking; Shutting your appliance down
Malfunctions You may be able to rectify the following faults by checking the possible causes yourself: Appliance does not function: – Is the appliance switched on? – Is the plug correctly fitted in the mains socket? – Is the fuse intact? Loud running noise: – Is the appliance set up firmly on the fl...
Page 16 - Description of the appliance (in the operating instructions); The socket must not be situated behind the appli; Door swing clearance at; This opening must not be
Setting up • Avoid positioning the appliance in direct sunlight or near cook - ers, radiators and similar sources of heat. • The floor on which the appliance stands should be horizontal and level. • Standard EN 378 specifies that the room in which you install your appliance must have a volume of 1 m...
Page 17 - Do not install the shut-off tap behind the appliance.; The water shut-off tap must not sit directly; Cabinet depth D; 25 mm + panel thickness
Appliance dimensions A = 76 mm B = 2027 mm C = 757 mm D = 610 mm E = 1413 mm F = 952 mm Installation dimensions The location of the socket can within a radius of 2000 mm from the appliance top center. The ice maker is fitted in the freezer compartment of the com - bined refrigerator-freezer. It must...
Page 18 - Panel dimensions - Inset installation style; Maximum panel weight; Refrigerator panel = 27 kg; Panel dimensions - Frameless installation style
Panel dimensions - Inset installation style Min. panel thickness = 16 mm Max. panel thickness = 38 mm Maximum panel weight Refrigerator panel = 27 kg Freezer drawer panel = 10 kg Panel dimensions - Frameless installation style Definition of Inset Installation Style Appliance and panels sit fully wit...
Page 19 - Top View; Front panel - door closed; Front; Door swing clearance -; Inset; Installation Style
Right side wall of appliance housing Front of appliance housing Top View Front panel - door closed Panel thickness Panel thickness Front panel - door opening angle = 115° Door swing clearance - Inset Installation Style 19
Page 20 - Frameless
Right side wall of appliance housing Front of appliance housing Top View Front panel - door closed Panel thickness Panel thickness Front panel - door opening angle = 115° Door swing clearance - Frameless Installation Style 20
Page 21 - tions; If the floor slopes down sideways, the anti-tipping; Ensure that there are no electric cables or water; Mounting options
Mounting the anti-tipping device WARNING! The supplied anti-tipping bracket must be installed in all cases. This prevents the appli- ance from tipping over when the fully loaded door is opened. Installation: 1. Mark the centre line of the appliance on the floor. Align the anti-tipping bracket centre...
Page 22 - Installation; combined refrigerator-freezer is connected to; Water pressure; The; must be between; water pressure; must lie between; If the water pressure with the inserted water
3. 4. 3. Insert the bent section of the hose through the opening at the right side of the appliance. 4. Move the hose to the front and con - nect with the valve connector. Be sure the connection is tightly arranged. Valve connector Installation 1. Place the appliance in front of the installation rec...
Page 23 - Be sure the connection is tightly arranged.; After the ice maker has been switched on, the water
6. Route the mains cable towards the socket. 7. Route the water hose towards the water shut-off tap. 6. 7. 8. Push the appliance slowly into the recess until the compressor mounting plate touches the anti-tipping bracket. 9. Fill the hose with water and connect to the shut-off tap. Be sure the conne...
Page 24 - To prevent the appliance from tipping forward
Mounting the ventilation grille Pull out the bottom freezer drawer. 1. Remove the blue protection film from the dust filter provided and insert the filter into its opening in the plinth. Engage the filter at the bottom, press down the button and click into place. 2. Remove the locking pins of both s...
Page 26 - Side view of the freezer drawer
Removing the mounting accessories from the refrigerator door Remove the cover 1 and unscrew the top and bottom attach - ment brackets 2 from the refrigerator door. These attachment brackets will be mounted onto the refrigerator door panel. Important! The securing nuts are needed for re-mounting the ...
Page 27 - Mounting the attachment brackets onto the door panels; Refrigerator door panel
Mounting the attachment brackets onto the door panels 1. Draw a line 1041 mm from the bottom side of the door panel.2. Draw a further line 107.5 mm from the bottom side of the door panel.3. Align one of the refrigerator door attachment brackets to the top line, as shown in the illustration below, an...
Page 28 - Mounting the refrigerator panel
fig. D Mounting the refrigerator panel fig. A fig. B fig. C 1. Screw in the adjusting pins on the underside of the refrigerator door completely (fig. A) . 2. Open the refrigerator door and sus - pend the refrigerator panel on the top adjusting pins (fig. B) . 3. Screw securing nuts onto the adjust -...
Page 29 - Do not try to change over the door hinges your-
Mounting the freezer panels 1. Pull out the top freezer drawer and screw on the pre-assembled panel. The same screws must be used as those used to screw on the attachment brackets (3.5 x 13). 2. Close the freezer drawer and check the position of the panel. Adjust the height of the panel by undoing t...
