Liebherr 7083-103-00 - Manual

Page 3 - Cabinet depth D; 25 mm + panel thickness

3 Installation dimensions The ice maker is fitted in the freezer compartment of the com - bined refrigerator-freezer. It must be connected to the mains water supply to work. The water shut-off tap must be positioned within the areas marked in grey. The socket must be positioned within the areas mark...

Page 5 - Panel dimensions - Inset installation style; Maximum panel weight; Refrigerator panel = 12 kg; Panel dimensions - Frameless installation style

5 Panel dimensions - Inset installation style Min. panel thickness = 16 mm Max. panel thickness = 19 mm Maximum panel weight Refrigerator panel = 12 kg Freezer drawer panel = 10 kg Panel dimensions - Frameless installation style

Page 6 - Right side wall of appliance housing; Front of; Top View; Door swing clearance -; Inset; Installation Style

6 Right side wall of appliance housing Front of appliance housing Top View Front panel - door closed Panel thickness Panel thickness Fro nt p an el - do or o pe nin g a ng le = 10 5° Door swing clearance - Inset Installation Style

Page 7 - Frameless

7 Door swing clearance - Frameless Installation Style Right side wall of appliance housing Front of appliance housing Top View Front panel - door closed Panel thickness Panel thickness Fro nt p an el - do or o pe nin g a ng le = 10 5°

Page 8 - Mounting the anti-tipping device; If the floor slopes down sideways, the anti-tipping; Connection to the water supply; water pressure; Inset installation style >

8 Mounting the anti-tipping device WARNING! The supplied anti-tipping bracket must be installed in all cases. This prevents the appliance from tipping over when the fully loaded door is opened. CAUTION! Ensure that there are no electric cables or water pipes in the wall section to which the anti-tip...

Page 9 - Compressor mounting; To prevent the appliance from tipping forwards, the com-; Installation

9 3. Insert the bent section of the hose through the opening at the rear of the appliance. 4. Connect the hose to the solenoid valve at the front side of the appliance. WARNING! Do not connect the appliance to the power supply until the installation is completed. CAUTION! Lay the mains cable and the...

Page 10 - Levelling the appliance; The front feet of the ap-; Before fitting the door panels; The securing nuts are needed for re-mounting the pre-; Adjusting the front of the drawer; Side view of the freezer drawer; Fasten the appliance in the recess

10 Levelling the appliance 1. Adjust the height of the appliance at the front by twisting the adjustable feet 1 (A/F 27). Use the open-ended spanner provided. Caution! The front feet of the ap- pliance must be firmly placed on the floor. 2. Adjust the height of the appliance at the rear by turning t...

Page 11 - Mounting the attachment brackets onto the door panels; Refrigerator door panels

11 Mounting the attachment brackets onto the door panels Mark lines on the refrigerator door panels as shown in Fig. A. Align the dismounted brackets of the refrigerator doors to the lines on the refrigerator door panels as shown in Fig. A 1. Fasten each bracket with any hole wherever possible using...

Page 12 - Mounting the refrigerator panel

12 Mounting the refrigerator panel The description is for one panel only. The procedure is the same for both panels. fig. B fig. C 1. Open the refrigerator door and suspend the refrigerator panel on the top adjusting pins (fig. B) . 2. Screw securing nuts onto the adjusting pins and slightly tighten...

Page 14 - To ensure fault-free operation of the appliance, you must; Mounting the freezer panels

14 Mounting the dust filter The supplied dust filter prevents that dirt enters the motor compart - ment, reducing the refrigeration performance. Therefore always install the dust filter.1. Pull the bottom freezer drawer right out. 2. Remove the protective film from the dust filter. Insert the filter...

Liebherr 7083-103-00 - Manual

Table of Contents:

Summary

Other Liebherr Models