Liebherr HCB 2062 - Manuals

Page 2 - IMPORTANT; mportant; Contents; TO THE INSTALLER

2 PLEASE READ AND FOLLOW THESE INSTRUCTIONS These instructions contain Warning and Caution statements. This information is important for safe and efficient installation. Always read and follow all Warning and Caution statements! Warning indicates a potentially hazardous situation which, if not avoid...

Page 3 - Customer’s Responsibility; • Floors can support refrigerator’s weight plus; Electrical Requirement; • Electrically ground appliance.

3 I nstallatIon G uIdelInes ELECTROCUTION HAZARD Electrical grounding required. This appliance is equipped with a three-prong (grounding) polarized plug for your protection against possible shock hazards. • Do not remove the round grounding prong from the plug. • Do not use a two-prong grounding ada...

Page 4 - Figure 3; Door swing clearence; Figure 2; lannInG

Unit Dimensions - Figure 1 Unit Venting - Figure 3 HC/HCB 20 appliances do not require any ventilation openings in the cabinet. The required airflow is directed through the toe kick area. It is important to use the provided cover grille for the ventilation opening. This opening must not be covered w...

Page 5 - Cabinet Opening Dimensions; Figure 4; For appliance with panel to be

Cabinet Opening Dimensions - Figure 4 Figure 4 IMPORTANT Do not install the shut-off valve behind the appliance. IMPORTANT The free length of the water supply line must be at least 31-1/2" (800 mm) when the tube comes out of the pre- scribed opening. IMPORTANT For 24" cabinets, the water lin...

Page 6 - Appliance and panels sit fully within the opening; Panel Dimensions - Inset Installation Style

Figure 5 The panels should be at least 5/8 inch (16 mm) thick to allow the connecting rails to be fastened to them. IMPORTANT The maximum panel thickness is 3/4" (19 mm). Cabinet Opening A Refrigerator door panel B 80" (2032 mm) 45 - 1/4" (1150 mm) 84" (2134 mm) 49 - 1/4" (1251 m...

Page 7 - Panel Dimensions - Frameless Installation Style

Figure 6 IMPORTANT The maximum panel thickness is 3/4" (19 mm). Cabinet Opening C Refrigerator door panel D 80" (2032 mm) 45 - 3/4" (1162 mm) 84" (2134 mm) 49 - 3/4" (1264 mm) With this installation style, these wider appliance panels partially overlay the shared side gables of a...

Page 8 - Figure 9; Mounting the anti tipping device; Figure 7; lockInG

Secure the appliance in place so it does not tip forward when the fully stocked door is opened. The anti tipping bracket is provided with the appliance. 1. Mark the center line of the appliance on the back wall. Align the anti tipping bracket center to this line. Be sure that there is no plumbing or...

Page 9 - Cover strips; • Remove the cover band from the strips and stick; Be sure the wooden spacer is fastened; Measuring for mounting the wooden spacer

Figure 12 Cover strips - Figure 12 Before connection to the water supply, the cover strips provided must be fitted to the appliance. It is necessary because the appliance will be moved into its recess. • Remove the cover band from the strips and stick them to the left and right front edge of the app...

Page 10 - metric; Connection to the Water Supply; plied with the refrig-; Do not install the shut-off valve behind the

10 I ce m aker Figure 14 • The solenoid valve has a metric R3/4 male connector. A R3/4 (metric) to a 1/4" OD adapter is supplied with the ice maker. • Insert the water strainer provided into the OD adapter with the cavity downwards. IMPORTANT Be sure the strainer is inserted with the cavity down...

Page 11 - To prevent the appliance from tipping

11 I ce m aker Figure 16 Figure 17 9. Open the shut-off valve for the water supply and check the entire water system for leaks. IMPORTANT After starting up the appliance, the water pipe system must be purged of any air. Refer to chapter "Bleeding the ice maker" in the operating instructions....

Page 12 - The nuts are needed to fit the premounted; Leveling the Appliance; Adjusting the front of the drawer; nstallatIon

Fasten the appliance in the recess - Figure 20 Fasten the appliance in the recess through the upper and lower hinges of the refrigerator doors. Use 2 screws for each hinge. screws (4 x 16 mm) Before mounting the door panels - Figure 21 Remove cover 1 and unscrew the upper attachment bracket 2 of bot...

Page 13 - Mounting the attachment brackets onto the door panels; Mark lines on the refrigerator door panels as shown in

Mounting the attachment brackets onto the door panels - Figure 22 Mark lines on the refrigerator door panels as shown in Figure 22. Align the dismounted brackets of the refrigerator doors to the lines on the refrigerator door panels as shown in Figure 22 a. Fasten each bracket with any hole wherever...

Page 14 - Do not overtighten. Do not use a power

Mounting the refrigerator door panels - Figures 24 - 33 The description is for one panel only. The procedure is the same for both panels. 1. Open the refrigerator door and hang the panel on the adjusting bolts (Figure 24) . 2. Screw on the hex nuts to the adjusting bolts and finger tighten temporari...

Page 15 - The soft-stop cylinder retracts in the

To make it possible to fasten the refrigerator panel at the bottom the soft-stop cylinder must be dismantled. 5. Grasp the soft-stop cylinder and pull down (Figure 26) . The soft-stop cylinder retracts in the detached state. Figure 26 Figure 27 6. Transfer the lower edge of the attachment bracket on...

Page 17 - Mounting the ventilation grille; Remove the blue protection film from the dust

Mounting the ventilation grille - Figure 34, 35 1. Pull out the bottom freezer drawer. 2. Remove the blue protection film from the dust filter provided and insert the filter into its opening in the toe kick area as shown in Figure 34. Attach the filter at the bottom, press down the button and click ...