Lexmark MS310DN - Manual

1 Right side 305 mm (12 in.) 2 Front 510 mm (20 in.) 3 Left side 205 mm (8 in.) 4 Rear 205 mm (8 in.) 5 Top 305 mm (12 in.) Printer configurations CAUTION—POTENTIAL INJURY: To reduce the risk of equipment instability, load each tray separately. Keep all trays closed until needed. You can configure y...

Using the printer control panel 1 2 3 4 5 6 7 8 Light or button Color Description 1 Error light Yellow An error has occurred. 2 Paper jam light Yellow A paper jam has occurred. 3 Load or remove paper light Yellow Paper must be loaded in the tray or removed from the bin. 4 Toner low or replace imagin...

Light or button Color Description 8 Stop or cancel button Red Use this to cancel a print job. Understanding the printer control panel light sequences The printer control panel lights can mean different things, depending on the light sequence. The lights can be on, off,blinking, or blinking slowly, i...

Primary light sequence Supplemental light sequence Message Paper jam, open reardoor Paper jam, removestandard tray to clearduplex Paper jam, open frontdoor Paper jam, removestandard tray Paper jam, removeoptional tray Paper jam, manualfeeder Using the Embedded Web Server Note: This functionality is ...

To download and install the Local Printer Settings Utility, see “Installing the Local Printer Settings Utility” on page 20. To access the Local Printer Settings Utility: In Windows 8 From the Search charm, type local printer settings utility , and then navigate to: Apps list > Local Printer Setti...

Additional printer setup Installing hardware options Installing optional trays CAUTION—SHOCK HAZARD: If you are accessing the controller board or installing optional hardware or memory devices sometime after setting up the printer, then turn the printer off, and unplug the power cordfrom the electri...

7 Align the printer with the tray, and then slowly lower the printer into place. 8 Connect the power cord to the printer, then to a properly grounded electrical outlet, and then turn on the printer. 1 2 Note: When the printer software and any hardware options are installed, it may be necessary to ma...

Warning—Potential Damage: Do not touch the USB cable, any network adapter, or the printer in the area shown while actively printing. Loss of data or a malfunction can occur. 1 2 3 4 5 6 7 Use the To 1 USB port * Attach an optional wireless network adapter. 2 USB printer port Connect the printer to a...

1 Obtain a copy of the software installer package. • From the Software and Documentation CD that came with your printer. • From our Web site:Go to www.lexmark.com , and then navigate to: SUPPORT & DOWNLOADS > select your printer > select your operating system > download your software in...

Updating available options in the printer driver When any hardware options are installed, you may need to manually add the options in the printer driver to makethem available for use. For Windows users 1 Open the printers folder. In Windows 8 From the Search charm, type run , and then navigate to: A...

Networking Notes: • Purchase a MarkNet TM N8352 wireless network adapter first before setting up the printer on a wireless network. For information on installing the wireless network adapter, see the instruction sheet that came with theadapter. • A Service Set Identifier (SSID) is a name assigned to...

d Click the IP tab. e Type the printer IP address in the address field, and then click Add . • For AppleTalk printing: Notes: – Make sure AppleTalk is activated on your printer. – This feature is supported only in Mac OS X version 10.5. a From the Apple menu, navigate to: System Preferences > Pri...

Notes: – If you do not know the SSID of the network that your computer is connected to, then launch the wireless utilityof the computer network adapter, and then look for the network name. If you cannot find the SSID or thesecurity information for your network, then see the documentation that came w...

Using the Wireless Setup Assistant (Macintosh only) The Wireless Setup Assistant lets you: • Configure the printer to join an existing wireless network. • Add a printer to an existing ad hoc network. • Change the wireless settings after installation. • Install the printer on additional network compu...

5 Turn off the printer, and then disconnect the Ethernet cable. Then wait for at least five seconds, and then turn theprinter back on. 6 To verify if your printer is connected to the network, print a network setup page again. Then in the Network Card[x] section, see if the status is “Connected”. Pri...

Loading paper and specialty media The selection and handling of paper and specialty media can affect how reliably documents print. For more information,see “Avoiding jams” on page 92 and “Storing paper” on page 46. Setting the paper size and type Using the Embedded Web Server 1 Open a Web browser, a...

Loading the multipurpose feeder Use the multipurpose feeder when printing on different paper sizes and types or specialty media, such as card stock,transparencies, paper labels, and envelopes. You can also use it for single ‑ page print jobs on letterhead. 1 Open the multipurpose feeder. 1 2 a Pull ...

• Load letterhead faceup with the top edge entering the printer first. For two ‑ sided (duplex) printing, load letterhead facedown with the bottom edge of the sheet entering the printer first. • Load envelopes with the flap on the left side facedown. Warning—Potential Damage: Never use envelopes wit...

Notes: • Print a network setup page or menu settings page, and then locate the IP address in the TCP/IP section. TheIP address appears as four sets of numbers separated by periods, such as 123.123.123.123. • If you are using a proxy server, then temporarily disable it to load the Web page correctly....

Paper and specialty media guide Additional information for printing on specialty media may be found in the Cardstock and Label Guide available at http://support.lexmark.com . Paper guidelines Selecting the correct paper or specialty media reduces printing problems. For the best print quality, try a ...

Grain direction Grain refers to the alignment of the paper fibers in a sheet of paper. Grain is either grain long , running the length of the paper, or grain short , running the width of the paper. For 60–90 ‑ g/m 2 (16–24 ‑ lb) bond paper, grain long paper is recommended. Fiber content Most high ‑ ...

• Avoid papers with rough or heavily textured surfaces. Use papers printed with heat ‑ resistant inks designed for use in xerographic copiers. The ink must be able to withstand temperatures up to 230°C (446°F) without melting or releasing hazardous emissions. Use inks that are not affected bythe res...

Lexmark does not endorse specific suppliers, although a converter’s product list for special applications is maintained.However, the following paper choice guidelines will help alleviate the environmental impact of printing: 1 Minimize paper consumption. 2 Be selective about the origin of wood fiber...

• Do not use labels with exposed adhesive. • Do not print within 1 mm (0.04 inch) of the edge of the label, of the perforations, or between die ‑ cuts of the label. • Make sure the adhesive backing does not reach to the edge of the sheet. Zone coating of the adhesive should beat least 1 mm (0.04 inc...

Supported paper sizes, types, and weights Supported paper sizes Paper size Standard tray Optional 250 ‑ or 550 ‑ sheet tray Multipurpose feeder Duplex mode A4 210 x 297 mm (8.3 x 11.7 in.) A5 148 x 210 mm (5.8 x 8.3 in.) X A6 105 x 148 mm (4.1 x 5.8 in.) X X JIS B5 182 x 257 mm (7.2 x 10.1 in.) X Le...

Paper size Standard tray Optional 250 ‑ or 550 ‑ sheet tray Multipurpose feeder Duplex mode DL Envelope 110 x 220 mm (4.3 x 8.7 in.) X X X C5 Envelope 162 x 229 mm (6.4 x 9 in.) X X X B5 Envelope 176 x 250 mm (6.9 x 9.8 in.) X X X Other Envelope 229 x 356 mm (9 x 14 in.) X X X 1 This size setting fo...

Printing This chapter covers printing, printer reports, and job cancelation. Selection and handling of paper and specialty mediacan affect how reliably documents print. For more information, see “Avoiding jams” on page 92 and “Storing paper”on page 46. Printing documents Printing a document 1 From t...

Notes: • Print a network setup page or menu settings page, and then locate the IP address in the TCP/IP section. TheIP address appears as four sets of numbers separated by periods, such as 123.123.123.123. • If you are using a proxy server, then temporarily disable it to load the Web page correctly....

Understanding the printer menus You may print a menus list by printing the menu settings and network setup pages. Access the menus from a networkprinter by using the Embedded Web Server. If your printer is connected by USB or parallel cable, then access the menususing the Local Printer Settings Util...

Configure MP menu Use To Configure MP CassetteManualFirst Determine when the printer selects paper from the multipurpose feeder. Notes: • Cassette is the factory default setting. Cassette configures themultipurpose feeder as the default paper source. • Manual sets the multipurpose feeder only for ma...

Use To Rough Envelope Texture Rough Specify the relative texture of the rough envelopes loaded. Letterhead Texture SmoothNormalRough Specify the relative texture of the letterhead loaded. Note: Normal is the factory default setting. Preprinted Texture SmoothNormalRough Specify the relative texture o...

Use To Cotton/Rough Weight LightNormalHeavy Specify the relative weight of the cotton or rough paper loaded. Note: Heavy is the factory default setting. Custom [x] Weight LightNormalHeavy Specify the relative weight of the custom paper loaded. Notes: • Normal is the factory default setting. • The op...

Use To Custom [x] Loading DuplexOff Determine and set two ‑ sided printing for all print jobs that specify Custom [x] as the paper type. Note: Custom [x] Loading is available only if the custom type is supported. Notes: • Duplex sets two ‑ sided printing as the default for all print jobs unless one ...

Settings menu General Settings menu Use To Display Language EnglishFrancaisDeutschItalianoEspanolDanskNorskNederlandsSvenskaPortugueseSuomiRussianPolskiGreekMagyarTurkceCeskySimplified ChineseTraditional ChineseKoreanJapanese Set the language of the text appearing on the Embedded WebServer, Local Pr...

Print Settings Setup menu Use To Printer Language PCL EmulationPS Emulation Set the default printer language. Notes: • PCL Emulation is the factory default setting. • PCL Emulation uses a PCL interpreter for processing printjobs. • PS Emulation uses a PostScript interpreter for processingprint jobs....

Finishing menu Use To Sides (Duplex) 1 sided2 sided Specify whether two ‑ sided (duplex) printing is set as the default for all print jobs. Notes: • “1 sided” is the factory default setting. • You can set two ‑ sided printing from the software program. For Windows users: 1 Click File > Print . 2 ...

Use To Paper Saver Off2 ‑ Up 3 ‑ Up 4 ‑ Up 6 ‑ Up 9 ‑ Up 12 ‑ Up 16 ‑ Up Print multiple ‑ page images on one side of a paper. Notes: • Off is the factory default setting. • The number selected is the number of page images that will print per side. Paper Saver Ordering HorizontalReverse HorizontalRev...

Use To Tray Renumber Restore Defaults YesNo Restore all tray and feeder assignments to the factory default settings. Security menu Set Date and Time menu Use To Current Date and Time View the current date and time settings for the printer. Manually Set Date and Time [input date/time] Enter the date ...

Saving money and the environment Lexmark is committed to environmental sustainability and is continually improving its printers to reduce their impacton the environment. We design with the environment in mind, engineer our packaging to reduce materials, and providecollection and recycling programs. ...

Saving energy If your printer is connected to a computer by a USB or parallel cable, then use the Local Printer Settings Utility forWindows or Printer Settings for Macintosh. If your printer is connected to the network, then use the Embedded WebServer. Note: Some features are available only in selec...

Notes: • Print a network setup page or menu settings page, and then locate the IP address in the TCP/IP section. • If you are using a proxy server, then temporarily disable it to load the Web page correctly. 2 Click Settings > General Settings > Timeouts . 3 In the Sleep Mode field, enter the ...

• If you are using a proxy server, then temporarily disable it to load the Web page correctly. 2 Click Settings > General Settings > Schedule Power Modes . 3 From the Action menu, select the power mode. 4 From the Time menu, select the time. 5 From the Day(s) menu, select the day or days. 6 Cl...

Returning Lexmark cartridges for reuse or recycling Lexmark Cartridge Collection Program diverts millions of Lexmark cartridges from landfills annually by making it botheasy and free for Lexmark customers to return used cartridges to Lexmark for reuse or recycling. One hundred percentof the empty ca...

Securing the printer Using the security lock feature The printer is equipped with a security lock feature. Attach a security lock compatible with most laptop computers inthe location shown to secure the printer in place. Statement of Volatility Your printer contains various types of memory that can ...

3 Press until the printer control panel light sequence matches the light sequence in the following illustration, and then press . ‑ Blinking ‑ Blinking The printer will restart several times during this process. Note: Wipe All Settings securely removes device settings, jobs, and passwords from the p...

Maintaining the printer Warning—Potential Damage: Failure to maintain optimum printer performance periodically, or to replace parts and supplies, may cause damage to your printer. Cleaning the printer Cleaning the printer Note: You may need to perform this task after every few months. Warning—Potent...

Using the printer control panel From the printer control panel, press , and then check the supply and part status in the Supply Information section. Estimated number of remaining pages The estimated number of remaining pages is based on the recent printing history of the printer. Its accuracy mayvar...

Item Regular cartridge Extra High Yield Toner Cartridge 500XA 2 Ultra High Yield Toner Cartridge 500UA 3 1 This cartridge is supported only in MS310d and MS310dn printer models. 2 This cartridge is supported only in MS410d and MS410dn printer models. 3 This cartridge is supported only in MS510dn, MS...

Replacing supplies Replacing the toner cartridge 1 Press the button on the right side of the printer, and then open the front door. 2 1 2 Pull the toner cartridge out using the handle. 3 Unpack the toner cartridge, and then remove all packing materials. 4 Shake the new cartridge to redistribute the ...

6 Close the front door. Replacing the imaging unit 1 Press the button on the right side of the printer, and then open the front door. 2 1 2 Pull the toner cartridge out using the handle. Maintaining the printer 86

6 Insert the imaging unit into the printer by aligning the arrows on the side rails of the imaging unit with the arrowson the side rails inside the printer. 7 Insert the toner cartridge into the printer by aligning the side rails of the cartridge with the arrows on the side railsinside the printer. ...

• If an optional tray is installed, then remove it from the printer. To remove the optional tray, slide the latch on theright side of the tray toward the front of the tray until it clicks into place. • Use the handholds located on both sides of the printer to lift it. • Make sure your fingers are no...

Managing the printer This chapter covers basic administrative support tasks using the Embedded Web Server. Finding advanced networking and administrator information This chapter covers basic administrative support tasks using the Embedded Web Server. For more advanced systemsupport tasks, see the Ne...

Notification Description Off The normal printer behavior for all supplies occurs. E ‑ mail Only The printer generates an e-mail when the supply condition is reached. The status of thesupply appears on the menus page and status page. Warning The printer displays a warning light sequence and generates...

Clearing jams Carefully select paper and specialty media and load them properly to avoid most jams. For more information, see“Avoiding jams” on page 92. If jams do occur, then follow the steps outlined in this chapter. Note: Jam recovery is set to Auto by default. The printer reprints jammed pages u...

• Do not slide the paper into the tray. Load paper as shown in the illustration. • Make sure the guides in the tray or the multipurpose feeder are properly positioned and are not pressing tightlyagainst the paper or envelopes. • Push the tray firmly into the printer after loading paper. Use recommen...

[x] ‑ page jam, remove tray 1 to clear duplex. [23y.xx] ‑ On ‑ On If the printer control panel light sequence matches the light sequence in the preceding illustration, then press twice quickly to see the supplemental light sequence. Supplemental light sequences Light sequence ‑ On ‑ On ‑ On Clearing...

Troubleshooting Understanding the printer messages Toner cartridge messages Cartridge, imaging unit mismatch [41.xy] ‑ On ‑ On If the printer control panel light sequence matches the light sequence in the preceding illustration, then do the following: 1 Check if both the toner cartridge and imaging ...

If the supplemental light sequence matches the light sequence in the preceding illustration, then install a toner cartridgethat matches the region number of the printer. x indicates the value of the printer region. y indicates the value of the cartridge region. x and y can have the following values....

Imaging unit messages Imaging unit low [84.xy] ‑ Blinking ‑ On If the printer control panel light sequence matches the light sequence in the preceding illustration, then you may need to order an imaging unit. If necessary, press on the printer control panel to continue printing. Imaging unit nearly ...

Paper loading messages Incorrect paper size, open [paper source] [34] ‑ On ‑ On If the printer control panel light sequence matches the light sequence in the preceding illustration, then press twice quickly to see the supplemental light sequence. ‑ On Troubleshooting 124

Remove paper from standard output bin ‑ Blinking If the printer control panel light sequence matches the light sequence in the preceding illustration, then do the following: 1 Remove the paper stack from the standard output bin. 2 From the printer control panel, press to continue printing. Printer c...

‑ On If the supplemental light sequence matches the light sequence in the preceding illustration, then try one or more ofthe following: • From the printer control panel, press to continue printing. Note: The printer discards any data received through the USB port. • Set the USB Buffer to Auto: – If ...

Insufficient memory to support Resource Save feature [35] ‑ On ‑ On If the printer control panel light sequence matches the light sequence in the preceding illustration, then press twice quickly to see the supplemental light sequence. ‑ On ‑ Blinking ‑ On Troubleshooting 141

‑ On ‑ On ‑ On ‑ On If the supplemental light sequence matches the light sequence in the preceding illustration, then try one or more ofthe following: • From the printer control panel, press to continue printing. A data loss will occur. • From the printer control panel, press to cancel the print job...

Printer had to restart. Last job may be incomplete. ‑ Blinking ‑ Blinking ‑ Blinking ‑ On If the printer control panel light sequence matches the light sequence in the preceding illustration, then press on the printer control panel to continue printing. For more information, visit http://support.lex...

Service error ‑ Blinking ‑ Blinking ‑ Blinking ‑ Blinking ‑ Blinking ‑ Blinking If the printer control panel light sequence matches the light sequence in the preceding illustration, then turn off theprinter, and then turn it back on. If the lights are still blinking after 10 seconds, then the printe...

‑ On If the supplemental light sequence matches the light sequence in the preceding illustration, then do the following: 1 Turn off the printer. 2 Unplug the power cord from the electrical outlet. Note: Optional trays lock together when stacked. Remove stacked trays one at a time from the top to the...

Option problems Cannot detect internal option Action Yes No Step 1 Turn off the printer, then wait for about 10 seconds, and then turn on theprinter. Does the internal option operate correctly? The problem is solved. Go to step 2. Step 2 Check if the internal option is properly installed in the cont...

Tray problems Action Yes No Step 1 a Open the tray and do one or more of the following: • Check for paper jams or misfeeds. • Check if the paper size indicators on the paper guides are alignedwith the paper size indicators on the tray. • If you are printing on custom ‑ size paper, then make sure tha...

Paper feed problems Paper frequently jams Action Yes No Step 1 a Pull out the tray, and then do one or more of the following: • Make sure paper lies flat in the tray. • Check if the paper size indicators on the paper guides are alignedwith the paper size indicators on the tray. • Check if the paper ...

Jammed pages are not reprinted Actions Yes No a From the Print Recovery menu, set Jam Recovery to Auto or On. Toaccess the Print Recovery menu, try one or more of the following: • If the printer is on a network, then open a Web browser and typethe printer IP address in the address field. Then naviga...

Action Yes No Step 6 a Remove and reinstall the printer software. For more information, see“Installing the printer software” on page 19. Note: The printer software is available at http://support.lexmark.com . b Resend the print job. Do the jobs print? The problem is solved. Contact customer support ...

Action Yes No Step 3 From the Eco ‑ Mode menu, change the environmental settings. To access the Eco ‑ Mode menu, do either of the following: • If the printer is on a network, then open a Web browser and type theprinter IP address in the address field. Then navigate to Settings > General Settings ...

Actions Yes No Step 3 a Depending on your operating system, open Printing Preferences orthe Print dialog, and then specify the paper type. b Resend the print job. Does the job print from the correct tray or on the correct paper? The problem is solved. Contact customer support . Incorrect characters ...

Action Yes No a From the Paper menu, set the paper size and type to match the paperloaded in the trays to be linked. To access the Paper menu, do eitherof the following: • If the printer is on a network, then open a Web browser and typethe printer IP address in the address field. Then navigate to Se...

Action Yes No Step 3 Reduce the number and size of fonts, the number and complexity ofimages, and the number of pages in the job. Does the job print and collate correctly? The problem is solved. Contact customer support . Unexpected page breaks occur Action Yes No Step 1 From the Setup menu, adjust ...

Action Yes No Step 1 a Check if there is packing material left on the imaging unit. 1 Remove the toner cartridge, and then the imaging unit. 2 Check if the packing material is properly removed from the imagingunit. Warning—Potential Damage: Do not expose the imaging unit to direct light for more tha...

Shadow images appear on prints A B C DA B C D A B C DA B C D Leading edge Trailing edge Action Yes No Step 1 Check if the paper loaded in the tray has the correct paper type and weight. Is paper with the correct paper type and weight loaded in the tray? Go to step 2. Load paper with thecorrect paper...

Action Yes No Step 1 a From the Quality menu, select a lower number to reduce the tonerdensity. To access the Quality menu, do either of the following: • If the printer is on a network, then open a Web browser and typethe printer IP address in the address field. Then, navigate to Settings > Print...

Action Yes No Step 2 From the Paper menu, check if the paper size setting matches the paperloaded in the tray. To access the Paper menu, do either of the following: • If the printer is on a network, then open a Web browser and type theprinter IP address in the address field. Then, navigate to Settin...

Action Yes No Step 3 a Depending on your operating system, specify the paper type andweight from Printing Preferences or from the Print dialog. b Resend the print job. Is the paper still curled? Go to step 4. The problem is solved. Step 4 a Remove the paper from the tray, and then turn it over. b Re...

Repeating defects appear on prints Action Yes No Step 1 Measure the distance between the defects. Check for a distance between the defects that equals: • 97 mm (3.82 in.) • 47 mm (1.85 in.) • 38 mm (1.5 in.) Is the distance between defects equal to one of the listed measurements? Go to step 2. 1 Che...

Print is too light ABCDEF Action Yes No Step 1 a From the Quality menu, increase the toner darkness. To access theQuality menu, do either of the following: • If the printer is on a network, then open a Web browser and typethe printer IP address in the address field. Then navigate to Settings > Pr...

Action Yes No Step 6 a Shake the imaging unit to redistribute the toner. 1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit. Warning—Potential Damage: Do not expose the imaging unit to direct light for more than 10 minutes. Extended exposure tolight may cause pr...

Printer is printing solid black pages Action Yes No Step 1 a Reinstall the imaging unit. 1 Remove the toner cartridge, and then the imaging unit. Warning—Potential Damage: Do not expose the imaging unit to direct light for more than 10 minutes. Extended exposure tolight may cause print quality probl...

Action Yes No Step 2 a Check if you are using a recommended type of transparency. b Resend the print job. Is the print quality still poor? Contact customer support . The problem is solved. Streaked horizontal lines appear on prints ABCDEABCDEABCDE Action Yes No Step 1 a Depending on your operating s...

Action Yes No Step 4 a Reinstall the imaging unit. 1 Remove the toner cartridge, and then the imaging unit. Warning—Potential Damage: Do not expose the imaging unit to direct light for more than 10 minutes. Extended exposure tolight may cause print quality problems. 2 Install the imaging unit, and t...

Action Yes No Step 3 a Load paper from a fresh package. Note: Paper absorbs moisture due to high humidity. Store paper in its original wrapper until you use it. b Resend the print job. Do streaked vertical lines still appear on prints? Go to step 4. The problem is solved. Step 4 a Reinstall the imag...

Action Yes No Step 3 a Redistribute the toner in the imaging unit. 1 Remove the toner cartridge, and then the imaging unit. 2 Firmly shake the imaging unit. Warning—Potential Damage: Do not expose the imaging unit to direct light for more than 10 minutes. Extended exposure tolight may cause print qu...

Action Yes No Step 2 a From the Paper Menu, set the paper type and weight to match thepaper loaded in the tray. To access the Paper Menu, do either of thefollowing: • If the printer is on a network, then open a Web browser and typethe printer IP address in the address field. Then navigate to Setting...

Toner rubs off Leading edge Trailing edge ABC DEF Action Yes No Step 1 From the Paper menu on the printer control panel, check the paper type,texture, and weight. To access the Paper Menu, do either of the following: • If the printer is on a network, then open a Web browser and type theprinter IP ad...

Embedded Web Server does not open Action Yes No Step 1 a Turn on the printer. b Open a Web browser, and then type the printer IP address. c Press Enter . Does the Embedded Web Server open? The problem is solved. Go to step 2. Step 2 Make sure the printer IP address is correct. a View the printer IP ...

Action Yes No Step 5 Temporarily disable the Web proxy servers. Proxy servers may block or restrict you from accessing certain Websites including the Embedded Web Server. Does the Embedded Web Server open? The problem is solved. Contact your system support person. Contacting customer support When yo...

Notices Product information Product name: Lexmark MS310d, MS310dn Machine type: 4514 Model(s): 220, 230 Edition notice May 2013 The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” ...

Trademarks Lexmark, Lexmark with diamond design, and MarkVision are trademarks of Lexmark International, Inc., registered inthe United States and/or other countries. Mac and the Mac logo are trademarks of Apple Inc., registered in the U.S. and other countries. PCL® is a registered trademark of the H...

Lexmark regulatory type/model LEX-M01-005; FCC ID: IYLLEXM01005; IC:2376A-M01005 Licensing notices All licensing notices associated with this product can be viewed from the root directory of the installation software CD. Noise emission levels The following measurements were made in accordance with I...

This symbol identifies static-sensitive parts. Do not touch in the areas near these symbols without first touching themetal frame of the printer. ENERGY STAR Any Lexmark product bearing the ENERGY STAR emblem on the product or on a start-up screen is certified to complywith Environmental Protection ...

DANGER - Invisible laser radiation when cartridges are removed and interlock defeated. Avoid exposure to laser beam.PERIGO - Radiação a laser invisível será liberada se os cartuchos forem removidos e o lacre rompido. Evite a exposição aos feixes de laser. Opasnost - Nevidljivo lasersko zra č enje ka...

Sleep Mode This product is designed with an energy-saving mode called Sleep Mode . The Sleep Mode saves energy by lowering power consumption during extended periods of inactivity. The Sleep Mode is automatically engaged after this productis not used for a specified period of time, called the Sleep M...

日本の VCCI 規定 製品にこのマークが表示されている場合、次の要件を満たしています。 この装置は、クラス B 情報技術装置です。この装置は、家庭環境で使用することを目的としていますが、この 装置がラジオやテレビジョン受信機に近接して使用されると、受信障害を引き起こすことがあります。 取扱説明書に従って正しい取り扱いをしてください。 VCCI-B European Community (EC) directives conformity This product is in conformity with the protection requirements of EC Council d...

To prevent radio interference to the licensed service, this device is intended to be operated indoors and away fromwindows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject tolicensing. The installer of this radio equipment must ensure that the a...

Íslenska Hér með lýsir Lexmark International, Inc. yfir því að þessi vara er í samræmi við grunnkröfur og aðrarkröfur, sem gerðar eru í tilskipun 1999/5/EC. Italiano Con la presente Lexmark International, Inc. dichiara che questo questo prodotto è conforme ai requisitiessenziali ed alle altre dispos...

—Use of printing media outside of Lexmark specifications —Refurbishment, repair, refilling or remanufacture by a third party of products, supplies or parts —Products, supplies, parts, materials (such as toners and inks), software, or interfaces not furnished by Lexmark TO THE EXTENT PERMITTED BY APP...

Index Numerics 250 ‑ sheet tray loading 30 550 ‑ sheet tray loading 30 Symbols [x] ‑ page jam, clear manual feeder. [250.xx] 108[x] ‑ page jam, clear standard bin. [20y.xx] 101[x] ‑ page jam, open front door. [20y.xx] 94[x] ‑ page jam, open rear door. [20y.xx] 99[x] ‑ page jam, remove tray 1 to clea...