KTI Networks KS-2240 - Manual

Page 5 - Table of Contents

-5- Table of Contents 1. Introduction ......................................................... 6 1.1 Features ............................................................................... 71.2 Specifications ....................................................................... 9 2. Installing t...

Page 8 - - IP Multicast packet filtering

-8- Management Features: Telnet for remote control Provides one RS232 local console port 802.1D Bridging - 802.1d spanning tree - 802.1P/Q GARP/GVRP Routing - RIP, RIP-2, DHCP-relay, ICMP router discovery message IP Multicast - IGMP Snooping - IP Multicast packet filtering TFTP - software up...

Page 10 - Installing the Switch; country of operation.

-10- 2. Installing the Switch The switch is designed to operate in workgroup environments without a complicated configuration procedure. It also features an auto-select 100- 240V, 50/60Hz power supply unit, which works in most countries around the world. Before connecting the supplied power cord int...

Page 12 - Mounting the Switches; Desktop Mounting

-12- 2.3 Mounting the Switches Desktop Mounting The switches can be placed on a desktop as a stand-alone unit. Allow enough ventilation space between the switch and the objects around it. Desktop Mounting Rack Mounting For mounting the switch into a 19-inch rack, a pair of mounting brackets is inclu...

Page 13 - Making Network Connections; Network Switched Ports; Standard

-13- 3. Making Network Connections 3.1 Network Switched Ports The following figure illustrates the switched ports provided on the front panel. The switch comes with 24 10/100BASE-TX Fast Ethernet switched ports and two Gigabit Ethernet slots for Gigabit Ethernet modules. The following table lists th...

Page 14 - 10/100BASE-TX Fast Ethernet Switched Ports; Gigabit Ethernet Slots

-14- 10/100BASE-TX Fast Ethernet Switched Ports Each switched port supports one connection to a LAN segments. Each segment is an independent shared network in one collision-domain. The connection can be to either a 10BASE-T or a 100BASE-TX device. MDI-X and MDI RJ-45 Connectors MDI-X jack is lab...

Page 17 - Gigabit Ethernet Slots; Module; Module Outline

-17- 3.3 Gigabit Ethernet Slots Each Gigabit Ethernet slot can accommodate one optional Gigabit Ether- net module for your Gigabit connection. The following modules are avail- able for selection: Module Wavelength Connector type Fiber cable 2240-SX 8 5 0 n m SC Multimode fiber 2240-SXJM 8 5 0 n m MT...

Page 18 - Module Installation

-18- The Gigabit Ethernet module supports auto-negotiation although it only operates on 1000M full-duplex mode. This function makes sure the system operates with maximum performance when it is connected to an auto-negotiation capable Gigabit Ethernet device. Duplex Mode Full duplex Fiber cable MM 50...

Page 19 - Making Trunk Connections

-19- 3.4 Making Trunk Connections Two switch units can be cascaded together through any regular switched data port on each unit when a port expansion is required. However, the transfer bandwidth between the two cascaded ports is limited to 200Mbps full duplex. To increase the bandwidth for the conne...

Page 24 - Performing Network Management; Management Support; by using the following methods:

-24- 5. Performing Network Management 5.1 Management Support The switch is featured with management functions and can be managed by using the following methods: _ Direct console connection over an RS232 cable _ Web browser software from Internet or Intranet over TCP/IP network _ Telnet software over...

Page 25 - Management objects; Advanced Management Activities

-25- 5.2 Management objects The following table lists the management objects supported by the system: LoginBasic Management Activities _ General Management Configuration - system parameters _ LAN Port Configuration - speed, link type, duplex, flow control _ Console Port Configuration - console baud ...

Page 26 - Setting IP Address; management before performing any in-band management operation.

-26- _ Other Protocols - GVRP, IGMP _ Port Trunking _ Port Mirroring _ File transfer - software upgrade LogoutSave settingsRestore default settingsReboot 5.3 Setting IP Address Before performing any management operation over network, the most important thing is to learn the detailed information abou...

Page 27 - Console Management; Any PC running Windows 95/98/ or NT can be used as a console. Use; Factory default settings of the Console port; activates the highlighted option.; Navigating Through the Console Interface To

-27- 5.4 Console Management Any PC running Windows 95/98/ or NT can be used as a console. Use the supplied RS232 cable and connect the console port to the COM port of your console PC. Use Windows Hyper Terminal program to perform this out-of-band management operations. Factory default settings of th...

Page 28 - from a PC COM port. The pin assignments of the connection are:; Switch DTE console port; nect to the managed unit using the IP address as URL address.; Telnet Management; Use Telnet software to perform the management operation. The most

-28- Use the supplied RS232 cable to make the console connection directly from a PC COM port. The pin assignments of the connection are: Switch DTE console port 9-pin PC COM port Pin 1 DCD -------------------------------- Pin 1 2 RXD -------------------------------- 3 3 TXD -------------------------...

Page 29 - SNMP and RMON Management; File transfer

-29- 5.7 SNMP and RMON Management SNMP management and RMON activities are performed at a network management station running SNMP network management application manager software with graphical user interface. The switch serves as an SNMP agent and provides RMON capabilities that allows network admini...

KTI Networks KS-2240 - Manual

Table of Contents:

Summary

Other KTI Networks Models