Page 4 - Table of Contents
- 4 - Table of Contents 1. Introduction .................................................................. 5 1.1 Features ........................................................................................... 61.2 Specifications .....................................................................
Page 8 - FX Port Optical Specifications
- 8 - Filtering address Multicast/Broadcast/Unicast address MAC address 2K entries Aging time 300 seconds Priority levels 2 outgoing priority queues (Ratio: High/Low = 4/1 ) VLAN mode 1. Port-based VLAN 2. 802.1Q VLAN (Tag-based) VLAN groups 16 groups (Group 0 ~ 15) Port PVID Full 12-bit VID, per po...
Page 9 - Management Specifications
- 9 - 1.4 Management Specifications Interface In-band web browser for IE4.0 and Netscape4.xPing command, ARP command Protocols IPv4, ARP, ICMP, UDP, TCP, DHCP client, Http server IP Setting DHCP dynamic IP mode (default mode)Static IP mode (default : 192.168.0.2) DHCP DHCP client ID = Device modelna...
Page 10 - Installing the Switches; Installation guide
-10- 2. Installing the Switches 2.1 Unpacking Check to see that you have everything before you start the installation.• Installation guide • The switch unit • Rubber magnet stand • One AC power adapter for the unit 2.2 Supply the Power Checking AC PowerBefore you begin the installation, check the AC...
Page 11 - Port Configuration; Link
-11- 2. Connect the power adapter cable to the switch before connecting the adapter to the AC outlet. 2.3 Port Configuration The switches provide port configuration function through the manage-ment interface. The setting options are shown as follows: Port Type TP PORTS FX PORT Auto-negotiation Enabl...
Page 16 - Making UTP Connections; Speed
-16- 2.7 Making UTP Connections TP Port ConfigurationUse management function to set the required TP port configuration. It isrecommended to set the highest ability for the TP ports as follows: Auto-negotiation = enabledSpeed = 100MDuplex = Full This is appropriate to support connection to almost eve...
Page 17 - Making Fiber Connection; Connector
-17- 2.8 Making Fiber Connection For different fiber connections, several alternative models can beselected for different fiber connections as follows: Model Ext. Connector Cable Max. Distance * -T ST MM 2 Km -C SC MM 2 Km -JM MT-RJ MM 2 Km -VM VF-45 MM 2 Km -L LC MM 2 Km -SA2 SC SM 20 Km *: The max...
Page 22 - Click to make the setup effective immediately
-22- 3.2 Port Setup The middle part of previous figure shows all port status of the connectedswitch. The right side shows port configuration setup page. Port StatusPort Status page displays the current port status. The status are: Port Port number (FX : FX port) Link Port link status, Up = link up, ...
Page 23 - This page includes the following functions:; IP Status; DHCP server. Disable to use Static IP setting.
-23- 3.3 IP Setup This page includes the following functions: IP Status Display information of current IP usedIf the current IP address is labeled (DHCP), it means theIP is assigned by DHCP server. IP Setup Set static IP address to be used when DHCP is disabledor when no DHCP server is available. DH...
Page 24 - ently with no packet modification.
-24- 3.4 VLAN Setup VLAN Mode SelectPort-based VLAN : Port-based VLAN 802.1Q base VLAN : IEEE 802.1Q Tag-based VLAN Click [Apply] to make change effective immediately. Note:1. Both modes use same group member port settings and Port PVID settings. When selecting Port-based VLAN, all ports are set toU...
Page 33 - About page shows switch model name and software version.
-33- 3.8 About About page shows switch model name and software version.
Page 34 - Appendix: Factory Default Values; Appendix: Effective Time of Setting Changes; Settings
-34- Appendix: Factory Default Values Settings Factory Default Values DHCP mode Enabled Static IP address 192.168.0.2 Netmask 255.255.255.0 Default gateway IP 192.168.0.1 Login password 123 TP ports Auto-negotiation enabled TP port speed 100M (the highest ability) TP port duplex Full duplex (the hig...