KTI Networks KCD-302 - Manual

Page 3 - Ethernet is a registered trademark of Xerox Corp.; Marking by the symbol; indicates compliance of this equipment to

- 3 - The information contained in this document is subject to change withoutprior notice. Copyright (C) All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. FCC NOTICE This device complies with Class B Part 15 the FCC Rules. Operation issubject to the following two cond...

Page 4 - Table of Contents

- 4 - Table of Contents 1. Introduction ......................................................... 5 1.1 Features ........................................................................................ 71.2 Specifications .................................................................................

Page 8 - This figure shows the important components of the converter:

- 8 - 1.2 Specifications This figure shows the important components of the converter:

Page 10 - LED Indicators; LED

-10- Configuration Setting Switches (SW) NO. FUNCTION SETTINGS SW1 TP Port mode OFF Auto-negotiation (default) ON Forced mode SW2 TP Port Duplex OFF Full duplex (default) ON Half duplex SW3 TP Port Speed OFF 100Mbps (default) ON 10Mbps SW4 802.3x function OFF Enable (default) ON Disable SW5 FX1 port...

Page 12 - Part 15 Class B

-12- CertificateFCC Part 15 Class B CE/EMC EMI EN50081-1 Class BEMS EN55024 CE/LVD Safety EN 60950 EN 50081-1/1992 :EN55022:1994/A1:1995/A2:1997 CISPR Class B EN61000-3-2:2000 Device <75W EN61000-3-3:1995/A1:2001 Clause 5 EN 55024:1998/A1:2001IEC 61000-4-2:1995 ESD Test IEC 61000-4-3:1995 RS Test...

Page 13 - The media converter series provides the following fiber options:; Model Specifications; Optical Specifications

-13- 1.3 Model Specifications The media converter series provides the following fiber options: Model Specifications KCD-302-xxx WaveL. Operating Model Ext. FX Connectors ( n m ) Fiber Distance Te m p e r a t u r e -2T FX1 : ST MMF 1310 2 km -10 ~ 55 o C FX2 : ST MMF 1310 2 km -10 ~ 55 o C -2C FX1 : ...

Page 14 - Special Functions

-14- 1.4 Special Functions Auto MDI/MDI-X FunctionThis function allows the TP port to auto-detect the twisted-pair signalsand adapts itself to form a valid MDI to MDI-X connection with theremote connected device automatically. Auto-negotiation FunctionWhen TP port is set on Auto-negotiation mode (SW...

Page 16 - the rear face of the device and screw it onto the device unit.

-16- 2.2 DIN-Rail Mounting In the product package, a DIN-rail bracket is provided for mounting theconverter in a industrial DIN-rail enclosure. The steps to mount the device onto a DIN-rail are:1. Clamp the bracket into the rear of the device. Align the bracket with the rear face of the device and s...

Page 19 - Mounting on a Plane Surface

-19- 2.3 Mounting on a Plane Surface An optional mounting bracket, as shown below is also available for mount-ing the device on a plane surface such as a wall, a wood board, or a metalplate in an industrial enclosure. To mount the device on a plane surface, the steps are:1. Clamp the bracket into th...

Page 22 - DC Power Jack; converter before connecting to the AC outlet.

-22- DC2 + and DC2 - can be installed with another power-pair for delivering themain power input to next converter in a cascading way. Note: Only up to four device units can be cascaded to receive power from one main power input source. DC Power Jack Connector: Jack D 6.3mm D 2.0mm AC Power Adapters...

Page 23 - Making TP Port Connection; TP port is featured to support connection to :; Link partner of TP port

-23- 2.5 Making TP Port Connection TP port is featured to support connection to : • Auto-negotiation devices • Auto-negotiation incapable 10BASE-T devices • Auto-negotiation incapable 100BASE-TX devices Network Cables10BASE-T: 2-pair UTP Cat. 3,4,5 , EIA/TIA-568B 100-ohm STP 100BASE-TX: 2-pair UTP C...

Page 24 - Making FX Port Connections; A variety of fiber options is provided as follows:

-24- 2.6 Making FX Port Connections FX1 port and FX2 port operate on 100Mbps and full duplex (factorydefault). A variety of fiber options is provided as follows: Model Specifications KCD-302-xxx WaveL. Operating Model Ext. FX Connectors ( n m ) Fiber Distance Te m p e r a t u r e -2T FX1 : ST MMF 13...

Page 26 - Configuration Switches & LED Indicators; Refer to the following sections for the related functions.

-26- 3 Configuration Switches & LED Indicators The following figure shows the locations of the configuration switchesand LED indicators: Refer to the following sections for the related functions.

Page 27 - Configuration Switches; SW

-27- 3.1 Configuration Switches SW FUNCTION SETTING & STATE SW1 TP Port mode OFF Auto-negotiation (default) ON Forced mode SW2 TP Port Duplex OFF Full duplex (default) ON Half duplex SW3 TP Port Speed OFF 100Mbps (default) ON 10Mbps SW4 802.3x function OFF Enable (default) ON Disable SW5 FX1 por...

Page 28 - Link Partner of FX Port; Note: For SMF connection, be sure the link partner is a full duplex

-28- 3.1.3 FX Port Duplex Settings SW5 SW6 This settings are used to set the duplex mode of the FX1 port and FX2port individually. It is recommended to use full duplex mode for FX con-nection unless its link partner is a fixed half duplex device. Half duplexmode will shorten the connection distance....

KTI Networks KCD-302 - Manual

Table of Contents:

Summary

Other KTI Networks Models