KTI Networks KCD-400 Series - Manuals

KTI Networks KCD-400 Series – Manual in PDF format online.

Manuals:

Manual

Manual KTI Networks KCD-400 Series

Summary

Page 3 - Ethernet is a registered trademark of Xerox Corp.; Marking by the symbol

- 3 - The information contained in this document is subject to change withoutprior notice. Copyright (C) All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. FCC NOTICE This device complies with Class B Part 15 the FCC Rules. Operation issubject to the following two cond...

Page 4 - Table of Contents

- 4 - Table of Contents 1. Introduction ......................................................... 5 1.1 Features ........................................................................................ 61.2 Specifications .................................................................................

Page 7 - This figure shows the important components of the converter:

- 7 - 1.2 Specifications This figure shows the important components of the converter:

Page 10 - Certificate; FCC

-10- Certificate FCC Part 15 Class B CE/EMC EMI EN50081-1 Class BEMS EN55024 CE/LVD Safety EN 60950 EN 50081-1/1992 :EN55022:1994/A1:1995/A2:1997EN61000-3-2:2000EN61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001IEC 61000-4-2:1995 ESD Test IEC 61000-4-3:1995 RS Test IEC 61000-4-4:1995 EFT/BURST Test IEC ...

Page 11 - Special Functions; Link Fault Pass Through Function

-11- 1.3 Special Functions Auto MDI/MDI-X Function This function allows the copper port to auto-detect the twisted-pair sig-nals and adapts itself to form a valid MDI to MDI-X connection with theremote connected device automatically. Link Fault Pass Through Function When a link fault is detected on ...

Page 12 - Far End Fault Function

-12- Far End Fault Function The fiber port is facilitated with this function. When the fiber port detectsa link failure on its receiving circuitry, it will send out an FEFI (Far EndFault Indication) signal to the remote connected device to indicate aremote fault is detected. It also is capable to re...

Page 17 - Install the mounting bracket on the device unit.

-17- 2.4 Panel Mounting The device is provided with an optional panel mounting bracket. Thebracket support mounting the device on a plane surface securely. Themounting steps are: 1. Install the mounting bracket on the device unit. 2. Screw the bracket on the device unit. 3. Screw the device unit on ...

Page 18 - The screw locations and final dimension are shown below:

-18- The screw locations and final dimension are shown below:

Page 19 - Using Terminal Blocks

-19- 2.5 Applying Power The power specifications of the device are: Operating Voltage +7 ~ +30VDC Power Consumption Max. 2.5W @30VDC The device provides two types of power interfaces, terminal block and DCpower jack for receiving DC power input from external power supply. Using Terminal Blocks Eithe...

Page 21 - Using DC Power Jack

-21- Using DC Power Jack DC Jack Connector: Jack D 6.3mm D 2.0mm AC Power Adapters: Optional commercial rated adapters are available for purchasing. Rated AC120V/60Hz DC7.5V 1ARated AC230V/50Hz DC7.5V 1ARated AC100V/50-60Hz DC7.5V 1ARated AC240V/50Hz DC7.5V 1A Connect power adapter DC plug to the DC...

Page 22 - Power Failure Relay Output; and

-22- 2.6 Power Failure Relay Output The device provides a relay output to report power failure event to aremote alarm monitoring system. The replay output is provided with twocontacts labeled PF+ and PF- in the terminal block interface. Use the provided 2P terminal plug for signal wiring and plug in...

Page 23 - Making Twisted Pair Copper Port Connection; Copper port is featured to support connection to :; Network Cables

-23- 2.7 Making Twisted Pair Copper Port Connection Copper port is featured to support connection to : • Auto-negotiation devices • Auto-negotiation incapable 10BASE-T devices • Auto-negotiation incapable 100BASE-TX devices Network Cables 1000BASE-T: 4-pair UTP Cat. 5e or 6, EIA/TIA-568B 100-ohm STP...

Page 24 - Making Fiber Port Connection; Installing SFP Fiber Transceiver

-24- 2.8 Making Fiber Port Connection The mini-GBIC (SFP) port must be installed with an SFP fiber trans-ceiver for making fiber connection. The device may come with an SFPtransceiver pre-installed when it is shipped from factory. Installing SFP Fiber Transceiver Turn off the power to the device. In...

Page 25 - LED Indicators; LED

-25- 3 LED Indicators The following figure shows the locations of the configuration switchesand LED indicators: 3.1 LED Indicators LED DISPLAY STATE INTERPRETATION PWR Power status ON The device is powered on. OFF The device is powered off. SFP SFP slot status ON An SFP transceiver is installed. OFF...

Page 26 - Appendix: Model Optical Specifications; Model Specifications; Reference; ture

-26- Appendix: Model Optical Specifications The media converter series provides the following fiber options: Model Specifications Reference Operating KCD-400-xx FX Wavelength Fiber Distance Tempera ture -SX LC 850nm 50/125 MMF 500m -20 ~ 70 o C 62.5/125 MMF 200m -LX LC 1310nm MMF 550m -20 ~ 70 o C S...