Page 2 - Table of Contents
Table of Contents 2 Important Safety Information 3 Before You Start 4 Assembly 5-23 Weight Ratios 24 Weight Stack Sticker Placement 25 Cable View 26 Top View 27 Exploded View 28 Parts List 29 Warranty Information 30
Page 3 - Important Safety Information; THANK YOU; for making this Power System unit a part of your exercise pro-; REGISTRATION CARD; • Product Series
Important Safety Information 3 THANK YOU for making this Power System unit a part of your exercise pro- gram. Keys Fitness and our Power System Series assures the very best in value,appearance, durability and biomechanics. This manual will guide you through the assembly process. If at any time you a...
Page 5 - Assembly
Page 10 - STEP 1; Figure 1
STEP 1 Insert the two Guide Rods (14) into Rear Base (3) and secure them in place using two Washers (91), two Spring Washers (89), and two Allen Bolts (86). Assembly 10 Figure 1
Page 11 - Figure 2
Assembly 11 STEP 2 Slide Seat Pad Support Receptacle (1) onto Rear Base (3) and secure in place using three Nylon Locknuts (93), six Washers (91), and three Bolts (80). Connect Front Upright (5) onto Seat Pad Support Receptacle (1) and secure together using two Nylon Locknuts (93), four Washers (91)...
Page 12 - Figure 3
Assembly 12 Step 3 Install the Main Upright (2) onto the Seat Pad Support Receptacle (1). Secure it in place using three Nylon Locknuts (93), six Washers (91), and three Bolts (80) on the side. Two Bolts (87), one Spring Washers (88),three Washers (90), one Nylon Locknut (92) will secure it at the b...
Page 13 - Figure 4
Assembly 13 Step 4 Slide one Weight Stack Bumper (62) down each Guide Rod (14). Next, slide the weight plates down the Guide Rods (14) in this order - five 15lb Plates (15), nine 10lb Plates (16), five 5lb Plates (17), and the TopPlate (18). Insert the Main Top Beam (4) onto the two Guide Rods (14) ...
Page 14 - Figure 5
Step 5 Attach Press Arm Support (6) to Main Upright (2) by aligning the holes and sliding the Shaft (19) through. Secure the Shaft (19) in place using two Set Screws (50).Install Press Arm (7) to Press Arm Support (6) by aligning the holes and sliding the Shaft (21) through. Secure the Shaft (21) in...
Page 15 - Figure 6
Assembly 15 Step 6 Slide Long Foam Tube (11) into the hole towards the lower part of the Main Upright (2).Slide the Shaft (44) into top of the Leg Extension Lever (8). Attach Leg Extension Lever (8) to Seat Pad Support Receptacle (1) and secure using one Washer (46), one Spring Washer (47), and one ...
Page 16 - Figure 7
Assembly 16 Step 7 Install Seat Pad (25) onto Seat Pad Support (9) using two Washers (91) and two Allen Bolts (85).Slide the Seat Pad Support assembly into Seat Pad Support Receptacle (1) and secure with Locking Pop Pin (43) Figure 7
Page 17 - Figure 8
Assembly 17 Step 8 Install a Plastic Washer (69) onto each side of the Long Foam Tube (11).Next, install Upholstered Roller Pad (27) onto each side of Long Foam Tube (11) and secure in place using Big Plug (68). Repeat the above step for the Seat Pad Support (9).Next, install Upholstered Roller Pad ...
Page 18 - Figure 9
Assembly 18 Step 9 Note: Stretch all cables out completely and make sure all twisting is removed before installing. Install Chest Press Cable (76) as detailed in Figure 9. Follow dotted lines to identify exact location of pulleys.Start by threading cable end into Top Plate (18). You will need the fo...
Page 24 - Weight Ratios
Weight Ratios 24 KPS-1550 Weight(lbs) 100% 95% 90% 65% 45% 10 10 9.5 9 6.5 4.5 15 15 14.25 13.5 9.75 6.75 20 20 19 18 13 9 25 25 23.75 22.5 16.25 11.25 30 30 28.5 27 19.5 13.5 35 35 33.25 31.5 22.75 15.75 45 45 42.75 40.5 29.25 20.25 55 55 52.25 49.5 35.75 24.75 65 65 61.75 58.5 42.25 29.25 75 75 71...
Page 25 - Weight Stack Sticker Placement
Weight Stack Sticker Placement 25 10 10 15 20 20 25 30 40 50 60 70 80 90 100 30 35 45 55 65 75 85 95 105 115 115 125 140 155 170 130 145 160 175 190 205 220 235 250 185 200 200 LB Stack 250 LB Stack Your new POWER SYSTEM unit can be purchased with either a 200 LB or 250 LB weightstack. Depending on ...
Page 26 - Cable View
Page 27 - Top View
Page 28 - Exploded View
Page 29 - Parts List
REF# KEYS PART# DESCRIPTION QTY. REF# KEYS PART# DESCRIPTION QTY. 1 223-00254 Seat Pad Support Receptacle 1 50 202-00143 Screw M8*6 5 2 223-00255 Main Upright 1 51 202-00154 Allen Bolt M8*35 1 3 223-00256 Rear Frame 1 52 210-00002 Weight Pin 1 4 223-00238 Main Top Beam 1 53 202-00121 Screw Bolt M12*...
Page 30 - Warranty Information; POWER SYSTEM SERIES
Warranty Information KEYS FITNESS PRODUCTS, L.P. POWER SYSTEM SERIES LIFETIME WARRANTY This Warranty applies in the United States and Canada to products manufactured or distributed byKeys Fitness Products, LP (“Keys”) under the KEYS brand name. The warranty period to the originalpurchaser is lifetim...
