Jet 578412 - User Manual - manualsarea.com

Page 2 - WARNING – To reduce risk of injury:

2 1.0 IMPORTANT SAFETY INSTRUCTIONS WARNING – To reduce risk of injury: 1. Read and understand the entire owner's manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serio...

Page 3 - SAVE THESE INSTRUCTIONS

3 32. Use proper extension cord. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table 2 (se...

Page 4 - Table of contents; Section

4 2.0 Table of contents Section Page 1.0 IMPORTANT SAFETY INSTRUCTIONS ....................................................................................................... 2 2.0 Table of contents ......................................................................................................

Page 5 - About this manual

5 3.0 About this manual This manual is provided by JET, covering the safe operation and maintenance procedures for the JET IBG-SSB series Buffing Machines. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdow...

Page 6 - Specifications

6 4.0 Specifications Table 1 Model number IBG-8SSB IBG-10SSB IBG-12SSB Stock number 577408 578410 578412 Motor and Electricals Motor type Induction, capacitor start, centrifugal switch Horsepower (true output) 1 HP 1-1/2 HP 2 HP Motor phase single Voltage 115/230V (prewired 115V) 230V only Cycle 60 ...

Page 7 - Mounting hole dimensions

7 1 subject to local/national electrical codes. 2 The specified values are emission levels and are not necessarily to be seen as safe operating levels. As workplace conditions vary, this information is intended to allow the user to make a better estimation of the hazards and risks involved only. L =...

Page 8 - Setup and assembly; Unpacking; Securing the buffer; Electrical connections

8 5.0 Setup and assembly 5.1 Unpacking Separate all parts from the packing material. Check each part against sect. 5.2, Carton contents, and make certain that all items are accounted for before discarding any packing material. (Check buffer to verify if any parts have been pre-mounted.) 5.2 Carton c...

Page 9 - GROUNDING INSTRUCTIONS; Extension cords; Voltage conversion

9 It is recommended that the buffer be connected to a minimum 15-amp circuit with circuit breaker or fuse. If using fuses, they should be time-delay fuses marked “D”. Local codes take precedence over recommen-dations. 6.1 GROUNDING INSTRUCTIONS 1. All Grounded, Cord-connected Tools: This tool must b...

Page 10 - Operation; General procedure; Changing Wheels

10 7.0 Operation Buffing wheels vary according to material and structure, and range from aggressive wheels that even out high spots and remove surface defects (“cutting”), to finer wheels that bring out the brilliant luster of the metal surface (“coloring”). The buffing wheel surface may be straight...

Page 11 - Wheel balancing; Adjusting concentricity; Buffer maintenance

11 8.2 Wheel balancing With the buffer unplugged from the power source , and arbor nuts snugged down, rotate wheels by hand and observe their motion. A buffing wheel has proper balance when: 1. The wheel’s outside face spins true and round; that is, its circumference rotates concentric to the arbor....

Page 12 - Troubleshooting IBG-SSB series Buffers

12 9.0 Troubleshooting IBG-SSB series Buffers Table 3 * WARNING: Some corrections may require a qualified electrician. Symptom Possible Cause Correction * Motor will not start. Not connected to power source. Verify that plug is properly inserted into receptacle. Motor cord cut or abraded. Replace wi...

Page 13 - Optional accessories

13 Symptom Possible Cause Correction * Excessive vibration. Wheel(s) out of balance; wobbling or not rotating concentric to arbor. Rake the wheel or replace it. Adjust wobble by rotating flange as needed. Improper mounting. Secure machine firmly to bench or stand. 10.0 Optional accessories These acc...

Page 14 - IBG-8SSB Buffer – Exploded View

Page 15 - IBG-8SSB Buffer – Parts List; Description

15 11.1.2 IBG-8SSB Buffer – Parts List Index No. Part No. Description Size Qty 1 ................ IBG8-01 ..................... Truss Head Screw ................................................... 3/16”-24 x 1/4” .............. 4 2 ................ IBG8-02 ..................... Rubber Pad .............

Page 16 - IBG-10SSB Buffer – Exploded View

Page 17 - IBG-10SSB Buffer – Parts List

17 11.2.2 IBG-10SSB Buffer – Parts List Index No. Part No. Description Size Qty 1 ................ IBG8-01 ..................... Truss Head Screw ................................................... 3/16”-24 x 1/4” .............. 4 2 ................ IBG10-02 ................... Rubber Pad .............

Page 18 - IBG-12SSB Buffer – Exploded View

Page 19 - IBG-12SSB Buffer – Parts List

19 11.3.2 IBG-12SSB Buffer – Parts List Index No. Part No. Description Size Qty 1 ................ IBG8-04 ..................... Truss Head Screw ................................................... 3/16”-24 x 1/4” .............. 4 2 ................ IBG10-02 ................... Rubber Pad .............

Page 20 - Electrical Connections; Wiring diagram for IBG-8SSB

20 12.0 Electrical Connections 12.1 Wiring diagram for IBG-8SSB

Page 21 - Wiring diagram for IBG-10SSB

Page 22 - Wiring diagram for IBG-12SSB

Page 23 - Warranty and Service

23 13.0 Warranty and Service JET ® warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period The general warranty lasts for the time p...

Jet 578412 - User Manual

Table of Contents:

Summary

Other Jet Grinding Machines Models