Jamo SS9000 - Manual
Jamo SS9000 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 5 – This Remote Start/Alarm System is designed to be used with; Automatic Transmission-Fuel Injection; INSTALLATION OF THE MAJOR COMPONENTS:; Do Not Mount The Module In The Engine Compartment
- Page 6 – STARTER INHIBIT RELAY:; This unit is to be used in vehicles with; AUTOMATIC TRANSMISSIONS; only! Although this combination; IT MUST NOT; installed into a vehicle with a; manually operated transmission; . Doing so may result in serious personal
- Page 7 – Do not remove the fuse holders from this wire harness. Fuses must be
- Page 8 – Starter Output; YELLOW START WIRE DETAIL; Ignition 1 Output
- Page 9 – WIRING THE 4 PIN ALTERNATE IGNITION HARNESS; Parking Brake Input
- Page 10 – Siren Output; WIRING CONNECTIONS: Multi Pin Accessory Input/Output Harness; Parking Light Flasher Feed; Parking Light Wiring Detail
- Page 11 – Siren Wiring Detail; Positive Door Switch Wiring Detail; Ground Output While Running Under Remote Start Control
- Page 12 – General Motors VATS By-Pass Diagram; Entry Illumination Ground Output
- Page 13 – Entry Illumination Detail; Negative Inhibit Input Plus Trigger When Armed; Grey w/ Black Trace Negative Inhibit Safety Shut Down Detail; Ground When Armed Output
- Page 14 – Positive Inhibit Input Plus Trigger When Armed; Brake Switch Positive Shutdown Detail; Chassis Ground Source; Chassis Ground Connection Detail
- Page 15 – Tachometer Input Signal; Tachometer Input Wiring Detail; Negative Door Trigger; Negative Door Switch Wiring Detail; Delayed 300mA Pulsed Channel 3 Output
- Page 16 – Channel 3 Relay Wiring Detail; 00mA Latched Channel 4 Output
- Page 18 – Pin Transponder Control Output:; operates, see remote start feature # 10 for setting this output.; Pin Shock Sensor:; connector shell of the control module.
- Page 19 – Wire Positive Switched Door Lock/Unlock Wiring Detail; In this application, the; WireGround Switched Door Lock/Unlock Wiring Detail
- Page 21 – Door Lock Control Circuits; change, the above sequence will have to be followed.; TIMED START OPERATION:
- Page 22 – Programming Tach Rate:; NOTE: All applications require that tach be programmed.
- Page 25 – METHOD 1
- Page 26 – METHOD 2; PIN IN VEHICLE DATA BUS PORT (DBI Port)
- Page 27 – COMPLETING THE INSTALLATION:; these mechanisms and impair the safe operation of the vehicle.
128-8843
1 of 28
1
Model SS9000
Installation Manual
SELECT
ABLE FEA
TURES
The select
able features can be set manually as explained below
, or with the RF feature programmer
.
T
o
set features using the RF programmer
, follow the instructions p
a
ckaged with the programmer
.
Factory default settings are indicated by bold text.
NOTE:
The method of manual override can either be selected to operate from the valet switch or operate as custom code.
Be certain to place a check mark indicating the method used in the box located on the last page of the owner's manual.
NOTE:
Keyless Entry Models with no horn output will Flash the Parking Lights instead of chirp where chirp is indicated.
Also, No data will be indicated if a feature is not available for a particular model. The unit will enter the feature but no s
election will be available.
RF Programmable Feature Bank 1 Is For T
ransmitter Programming See T
ransmitter Programming Guide.
RF Programmable Features Bank 2 Is Alarm Selectable Features:
Feature Selection
1 Chirp
2 Chirps
3 Chirps
4 Chirps
5 Chirps
6 Chirps
1st DoorL/UL
1 Sec.
3.5
Sec.
1 Sec L, Dbl. U/L
Dbl L, 1 Sec UL
Dbl
L,
Dbl
UL
1
S
l/350mS
ul
2nd
Accy
Lock
Auto Lock On
Auto Lock Off
3rd
Accy
. UL
Auto
UL
Dr
.
Auto
UL
A
ll
Auto UL Off
4th Headlights
On
Arm
On
Disarm
On Both
Off
5th Passive
Locks
Passive
Active
6th Pass/Act
Arm
Passive Arm
Active Arm
7th Siren/Horn
Siren/Horn
Siren Only
Horn
Only
8th Horn Chirp
10mS
16mS
30mS
40mS
50mS
9th O/R Method
Custom
Code
V
alet
10th 2 S
tep U/L
O
n
Off
1
1th Chp Del
Tx
O
n
Off
12th V
olt
s/HdW
ire
Not A
vailable
13th Trigger Circuits
All On
Doors Off
Hood/Trunk Off
All Off
14th L/UL Poll
Not A
vailable
15th
Aux Ch 5 Sel
Pulse
Push & Hold
1
0
S
e
c
2
0
S
e
c
Latch On/Off
Hold 3/S For O/P
16th
Aux Ch 6 Sel
Pulse
Push & Hold
1
0
S
e
c
2
0
S
e
c
Latch On/Off
Hold 3/S For O/P
17th
Aux Ch 7 Sel
Pulse
Push & Hold
1
0
S
e
c
2
0
S
e
c
Latch On/Off
Hold 3/S For O/P
18th Trigger Delay
Not Available
When using the RF programmer
, enter the program mode as follows:
Turn the ignition on
Press and release valet switch 3 times
T
turn ignition off then on
Press and hold valet switch for 5 seconds
Siren chirps 2 times indicating access to RF feature program mode.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
128-8843 5 of 28 5 This Remote Start/Alarm System is designed to be used with Automatic Transmission-Fuel Injection Vehicles Only! The unit provides a selectable ignition control that allows a number of selectable timed outputs for glow plug preheat in addition to a "Wait To Start Input" eit...
128-8843 6 of 28 6 THE PUSH-BUTTON/LED/RECEIVER/ANTENNA ASSEMBLY: The Spread Spectrum Receiver Antenna Assembly provided with this unit allows routing from below thedash board for maximum operating range. Choose a location above the belt line (dashboard) of the vehiclefor best reception. Special con...
128-8843 7 of 28 7 WIRING THE 6 PIN MAIN POWER HARNESS: WIRING THE 6 PIN MAIN POWER HARNESS: NOTE: Do not remove the fuse holders from this wire harness. Fuses must be used and located as close as possible to the power source for adequate protection of the vehicle. Fused RED w/ WHITE TRACE WIRE: + 1...
