Jamo APS-620N - Manual
Jamo APS-620N – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTALLATION OF THE MAJOR COMPONENTS:; Do Not Mount The Module In The Engine Compartment
- Page 3 – This switch must be; Do not remove the fuse holders from this wire harness.; WIRING THE 6 PIN MAIN POWER HARNESS Connector “C”:; + 12 volt Battery 1 Source 20A Max
- Page 4 – Wiring The 2 Pin Door Lock/Unlock Harness Connector “B”:
- Page 6 – Pulsed Ground Output Before Start
- Page 10 – Entry Illumination Ground Output; Programming Tach Rate:; NOTE: All applications require that tach be programmed.
- Page 11 – Setting Up The System Programming Features:
- Page 12 – PIN IN VEHICLE DATA BUS PORT (DBI Port); COMPLETING THE INSTALLATION:; ment. Make sure to clean the surface before affixing the label.; point these out to the customer.
128-8613a
1 of 12
Page 1
Model APS-620N
Installation Manual
This Remote Start System is designed to be used with
Automatic Transmission- Fuel Injection Vehicles Only!
COMPONENTS:
Control Module
2 Four Button RF Transmitters
Antenna/Receiver
1 1” X 1.75” Foam Pad
6 Pin Main Power Harness
7 Pin Accessory Harness
1 Hood Pin Switch
2 Pin Door Lock/Unlock Harness
3 Pin Parking Light/Ground Harness
2 Pin LED Assembly
2 Pin Push-Button Valet/Program Switch
3 Pin Antenna Receiver Harness
4 Pin Auxiliary Output Harness
Installation/Owners Guide
FEATURES:
Selectable Ignition Lock & Unlock
Selectable Door Lock/Unlock Output Timing
Safe Start (Requires double push of the start button to engage the remote start function)
On Board Parking Light Relay
Trunk Release Output
Horn Chirp Output With Selectable Duration
Selectable RF Start Chirp
Car Finder Mode (Can elect to have horn beep along with parking lights if connected)
Selectable Run Times 5, 10, 15, or 20 Minutes
Selectable Gas or Diesel
Automatic Start Timer (Can be set to start your car automatically at 2 or 4 hour intervals)
4 Negative Pulsed Aux Outputs Before Start, After Start, During Crank, After Shut Down
(To aid installation in many vehicles with factory alarm systems)
FCC NOTICE
This device complies with part 15 of the FCC rules. Operation of this device is subject to the following
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
Caution: Changes or modifications not expressly approved by the party responsible for compliance voids the
users authority to operate this device.
Rev A: Add new URL 11/4/2011
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
128-8613a 2 of 12 Page 2 INSTALLATION OF THE MAJOR COMPONENTS: CONTROL MODULE: Select a mounting location inside the passenger compartment (up behind the dashboard).The mounting location selected must be within 24" of the ignition switch wiring harness toallow connection of the 6 pin main wiring...
128-8613a 3 of 12 Page 3 the remote start unit. If the vehicle is being worked on, this hood switch prevents theremote start activation even if the RF command to start is issued. This switch must be installed in all applications. Failure to do so may result in personal injury orproperty damage. Moun...
128-8613a 4 of 12 Page 4 YELLOW Wire: Starter Output Careful consideration for the connection of this wire must be made to prevent thevehicle from starting while in gear. Understanding the difference between a me-chanical and an electrical Neutral Start Switch will allow you to properly identifythe ...
