Jamo SS9000 - Manuals

128-8843 8 of 28 8 YELLOW Wire: Starter Output Careful consideration for the connection of this wire must be made to prevent the vehicle fromstarting while in gear. Understanding the difference between a mechanical and an electricalNeutral Start Switch will allow you to properly identify the circuit...

128-8843 9 of 28 9 GREEN Wire: Ignition 2 Output Connect this wire to the ignition 2 wire from the ignition switch. This wire will show + 12 volts when theignition key is turned to the "ON" or "RUN" position and is some cases the "START" or CRANK" position.This wire will ...

128-8843 10 of 28 10 White w/ Black Trace Wire: (+) Siren Output This is the positive siren feed wire. Route this wire through a grommet in the firewall to the sirenlocation. Connect the White w/ Black Trace wire to the Red wire of the Siren. Secure the Black wireof the Siren to a known chassis grou...

128-8843 11 of 28 11 Siren Wiring Detail (-) TO VEHICLE'S CHASSIS GROUND TO WHITE w/BLACK WIRE OF MODULE Purple Wire: (+) Door Trigger Input If the vehicle's door courtesy light switches + 12 volts when the door is opened, (Some Fords and someImports), you must connect this wire to the positive outp...

128-8843 12 of 28 12 A. Shock Sensor By Pass: If there is a Non Plug in Shock Sensor used with the alarm system and it is not shunted during theRemote Start activation period, then vibration from the running vehicle can cause the alarm to trigger. Inthis case, connect the Light Blue Wire to terminal...

128-8843 13 of 28 13 Entry Illumination Detail Grey w/ Black Trace Wire: Negative Inhibit Input Plus Trigger When Armed The Grey w/ Black Trace wire provides an instant shutdown for the Remote Start Control Module wheneverit is grounded it also trigger the alarm when armed. Connect the Grey w/ Black...

128-8843 14 of 28 14 Brown w/ Black Trace Wire: Positive Inhibit Input Plus Trigger When Armed The Brown w/ Black Trace wire provides an instant shutdown for the Remote Start Control module when-ever it gets + 12 volts also triggers the alarm when armed. If the Brake lights switch in the vehicle swi...

128-8843 15 of 28 15 Green w/ Orange Trace Wire: Tachometer Input Signal This wire will continually monitor the engine's tach rate while the unit is under power of the Remote Startmodule. This wire will be routed to the vehicle ECM tach input or through the firewall into the enginecompartment and co...

128-8843 16 of 28 16 Channel 3 Relay Wiring Detail Green w/ Black Trace Wire: 300mA Latched Channel 4 Output The Green w/ Black Trace wire supplies a 300 mA switched output whenever channel four of the receiveris accessed. Pressing the pre-programmed transmitter button(s) will access channel four an...

128-8843 18 of 28 18 Black w/ Yellow Trace Wire: Ground Output During Start (Crank) The Black w/ Yellow Trace wire will provide a 300 mA ground output while the starter output of the remote start unit is active. This output can be used to activate the Crank Low/Bulb Test wire found in some GM vehicl...

128-8843 19 of 28 19 3 Wire Positive Switched Door Locks: In this application, the Red wire of the door lock harness provides a + 12 volt pulse during the disarmingsequence, or pulsed 12 volt unlock output. Connect the Red wire to the low current 12 volt signal wire fromthe factory door unlock switc...

128-8843 21 of 28 21 NOTE: Resistive Circuits, As Well As 4 Wire Polarity Reversal and 5 Wire Alternating 12 Volt Door Lock Control Circuits These applications require the use of additional components which may include relays, fixed resistors, orfor convenience, a Door Lock Interface. Refer to the A...

128-8843 22 of 28 22 TEMPERATURE START: When Temperature Start, Bank 3 feature #13 is selected on, the temperature start mode can be activatedfrom the transmitter. See owners manual for turning this feature on from the transmitter. Once activated,the unit will start 1 time if the vehicle temperature...

128-8843 25 of 28 25 NOTE: When completing an installation using either of the following key in sensor circuits, if the operator inserts the ignition key while the vehicle is running under the control of the Remote Start, thevehicle will shut down. This must be explained to the operator as it is in ...

128-8843 26 of 28 26 METHOD 2 To connect to the key in sensor circuit as shown for method 2:A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch.B. Cut this wire and connect the ignition cylinder side to chassis ground.C. Locate the key in sensor switch wi...

128-8843 27 of 28 27 COMPLETING THE INSTALLATION: After you have confirmed the operation of the Audiovox Remote Start unit and tested all the safety featuresof the system: NOTE: This unit has the ability to learn the dome light delay time, up to 60 seconds. If the vehicle has delay interior lights, ...