Page 2 - IMPORTANT SAFETY INFORMATION; READ ALL INSTALLATION INSTRUCTIONS; Save These Instructions for Future Use.
IMPORTANT SAFETY INFORMATION READ ALL INSTALLATION INSTRUCTIONS Jacuzzi Whirlpool Bath does not recommend prolonged periods of use of the steamer. Prolonged use of the steamsystem can raise excessively the internal human body temperature and impair the body’s ability to regulate itsinternal temperat...
Page 3 - Contents; GENERAL DESCRIPTION; SteamP
Contents Installation of Steam GeneratorSpecifications ______________________________________________________________________________ 1How to Select Generator Size and Electrical Requirements ___________________________________________ 2Locating the Steam Generator __________________________________...
Page 4 - INSTALLATION; Specifications and Sizing of the Steam Generator for the Room
How to Select Generator Size Step 1. Determine cubic footage of steam enclosure: multiply LENGTH inches x WIDTH inches x HEIGHT inches to find cubic inches. Divide cubic inches by 1728 to determine cubic feet. Step 2. Find steam enclosure size within the ranges shown on the chart for the supply volt...
Page 6 - Plumbing Instructions and Cautionary Notes on Installation
Plumbing Instructions and Cautionary Notes on Installation Minerals in the water or poor water quality can shorten the life of the steam generator or cause erratic operation ifthe tank is not drained regularly. Drain the tank frequently. Jacuzzi Whirlpool Bath also strongly recommendspurchasing and ...
Page 7 - Plumbing Diagram; SteamPr
INSTALLATION STEAM UNIT TO BE LEVEL AND UPRIGHT SEEPAGE 5 FOR SUGGESTED LOCATIONS WATER SUPPLYWITH SHUT-OFFVALVE (3/8 OR 1/2INCH COPPER) TO STEAM HEAD SEEPAGES 8 AND 9 FOR STEAMHEAD PLUMBING ANDINSTALLATION FOR VARI-OUS WALL SURFACES. STEAM PIPE 1/2 INCH(MINIMUM SIZE) COPPER.25 FOOT TOTAL MAXIMUMRUN...
Page 8 - Steam Head Installation for Various Wall Surfaces
INSTALLATION Steam Head Installation for Various Wall Surfaces Jacuzzi Whirlpool Bath recommends that the steam shield be used for all steam head installations. The steam shieldmust be installed if the steam head is located on acrylic (or other plastic) wall surfaces or above a bath rim. The steamhe...
Page 9 - 0 kW Steam Generator with Two Steam Heads
INSTALLATION 10 kW Steam Generator with Two Steam Heads Two steam heads may be installed with the Model E210000 Steam Generator, if desired. This will reduce thesound level of the exiting steam and will provide more even steam distribution and less heat concentration inlarger steam enclosures. POSIT...
Page 10 - Automatic Drain Valve Installation (Optional)
1. Apply thread compound sparingly to male threadson fitting A. (Keep thread compound from enteringthe valve.) 2. Using a backup wrench to hold fitting A, threadvalve assembly onto fitting and tighten. Valveoutlet must point as shown. 3. Make certain power is disconnected. Removetop cover. 4. Remove...
Page 11 - Steam Controls—Available Installation Methods
INSTALLATION Steam Controls—Available Installation Methods Various control packages are available for use with the steam generator. The following instructions (A–C, pages12 - 16) describe the different installations. Select one of the following control options: A. ON/OFF 30 minute control. B. 30 min...
Page 12 - Control cable at the generator
INSTALLATION APPLY SEALANT(100% SILICONE CAULK) 1-3/4" DIAMETER HOLEIN FINISHED WALL (OPTIONAL NUT INSTALLATIONIF BACK OF WALL ISACCESSABLE) A. STEAM CONTROL BY 30 MINUTE LOW VOLTAGE ON/OFF CONTROL. THIS LOW VOLTAGE CONTROL CANBE LOCATED INSIDE OR OUTSIDETHE STEAM ENCLOSURE 1. Control cable roug...
Page 13 - GENERAL INSTRUCTIONS FOR TEMPERATURE CONTROL MODELS
INSTALLATION GENERAL INSTRUCTIONS FOR TEMPERATURE CONTROL MODELS 1. Control Cable Rough-in The low voltage control can be mounted up to 25feet from the generator either inside or outside thesteam room, also see #6 optional secondary digitalgenerator control. String the 25' cable from thecontrol loca...
Page 14 - INSTALL GENERATOR CONTROL
INSTALLATION 5. INSTALL GENERATOR CONTROL The low voltage control can be mounted directly to afinished wall either inside or outside the steam room.Using a 2" hole saw, drill a hole in the finished wall wherethe control is to be mounted (the control cable shouldalready be roughed-in to this loca...
Page 15 - OPERATION; B. 30 MINUTE TEMPERATURE CONTROL
OPERATION B. 30 MINUTE TEMPERATURE CONTROL The 30 minute temperature control features a 30 minute press on timer lightingup the word "STEAM" and a thermostatic control preset to reach 120 degreesFahrenheit. The digital control can be mounted either inside or outside thesteam room. The preset...
Page 16 - C. DIGITAL TIME AND TEMPERATURE CONTROL
OPERATION C. DIGITAL TIME AND TEMPERATURE CONTROL The digital control features an adjustable 60 minute time and temperaturecontrol with digital display. The actual room temperature and time remainingare alternately displayed every 5 seconds. The primary control can bemounted either inside or outside...
Page 17 - SERVICE; Description of SteamPro Steam Generator
SERVICE Description of SteamPro Steam Generator The SteamPro series generator is the latest in modern steam generator design. The SteamPro steam generator uses aprinted circuit assembly to monitor and control all the equipment needed to produce steam. The system has three functions:a timer that cont...
Page 18 - TROUBLESHOOTING
TROUBLESHOOTING There are no user serviceable par ts in the Generator. All repair should be performed by a qualified service person.For additional assistance or the factory authorized service person nearest you call the Service Depar tment at 1-800-363-0251. The Trouble Shooting Guide below is meant...
Page 20 - WIRING DIAGRAM
WIRING DIAGRAM PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT. Jacuzzi Whirlpool Bath has obtained applicable code (standards) listings generally available on a national basis forproducts of this type. It is the responsibility of the ...
