Page 2 - IMPORTANT SAFETY INFORMATION; READ ALL INSTALLATION INSTRUCTIONS
IMPORTANT SAFETY INFORMATION READ ALL INSTALLATION INSTRUCTIONS Save These Instructions for Future Use. Owner's Record Jacuzzi Whirlpool Bath does not recommend prolonged periods of use of the steamer. Prolonged use of the steamsystem can raise the internal human body temperature excessively and imp...
Page 3 - Part I Assembly & Installation; Contents; Inspection and Shipping Claim
Part I Assembly & Installation Specifications _______________________________________________________________________ 2 General Information __________________________________________________________________ 3-4 Packaging __________________________________________________________________________ ...
Page 6 - Cleaning the J-Dream II
Electrical requirements Your J-Dream II, as it comes from the factory, requires a GFCI protected 240 VAC 3- wire 20 AMP 50-60 Hz circuit (2 conductorwith ground) for single (1) phase electrical service, and must be in a separate circuit having no other appliance connected inthat circuit. If you do n...
Page 8 - Letters (A) are used in the illustrations of the assembly procedure.
J-Dream II Owner's Manual Letters (A) are used in the illustrations of the assembly procedure. 6 FLAT WASHER 1/4" PAN HEAD SCREW#10-24 x 3/4" LOCK NUT 10-24 C WASHER SCREW B NUT D FLAT HEAD SCREWM4x10mm SCREW E PAN HEAD SCREW#12 x 1/2 SCREW F HEX BOLT1/4-20 x 1.5" BOLT G SELF-TAPPINGM6x5...
Page 10 - Locate Base to provide assembly access to all sides
8 Locate Base to provide assembly access to all sides Remove Base from carton labeled Base/Top. Place Clear Top in carton to prevent damage. (The Clear Top willnot be installed until the unit has been fully assembled and plumbed). Position the J-Dream base on the floor so that you have work access t...
Page 11 - Drain Fitting
9 Drain Fitting (provided with unit) Leave enough flexibility in the waste line to allow the end of the stub-out to be blocked temporarily in a position under flushwith the floor surface. This will allow the shower unit to slide across the floor into position without having to lift the showerunit. R...
Page 12 - Attach Seat Walls to Base
10 Attach Seat Walls to Base (J-Dream II with stereo shown) Bolts (8) Nuts (8) G J Align four holes on seat wall frameover base and insert bolts andtighten nuts from underneath. Washers (8) I EquipmentSeat Wall Non-EquipmentSeat Wall J-Dream II Owner's Manual
Page 13 - Attach Panel #2 to Seat Wall Frame
11 Attach Panel #2 to Seat Wall Frame Slide in panel feeding between frame and edge of seat wall. Align to frame and fasten panel to frame. Important: do notcaulk panel to seat wall as the seat wall is hinged and designed to swing open. F Screw (4) C Washer (4) Top View Move Frame Seat Wall Seals Wh...
Page 14 - Attach Panel #3 to Seat Wall Frame
12 Attach Panel #3 to Seat Wall Frame Slide in panel feeding between frame and edge of seat wall. Align to frame and fasten panel to frame. Important: do notcaulk panel to seat wall as the seat wall is hinged and designed to swing open. Top View Move Frame Seat Wall C Washer (4) F Screw (4) Seals Pa...
Page 15 - Install Back Wall
13 Install Back Wall Caulk the bottom and sides of back wall where indicated in the illustrations below. Install fasteners. Now align the backwall parallel to the pan lip to center the back wall between the seat walls. Screw (4) B Washer (8) C Nut (4) D Caulk A A Screw (4) B B Caulk Washer (8) C Nut...
Page 18 - Attach Painted Angle Brackets to Panels #1 and #4
Caulk B Screw (3) C Washer (3) Nut (3) D Top View (right side) Notch Side View (right side) B Screw (3) C Washer (3) Nut (3) D Top View (left side) Side View (left side) Notch Caulk 16 Attach Painted Angle Brackets to Panels #1 and #4 Note that each angle bracket has a notch on the top and bottom. T...
Page 19 - Attach Door Frame to Angle Brackets and Base Frame
17 Attach Door Frame to Angle Brackets and Base Frame Before proceeding, make sure the seat walls are closed and fastened. See detail B on page 15. Align door frameover tabs on base frame and pan lip. Pan lip is to fit into corner posts of door frame. Align holes along sides of doorframe with angle ...
Page 21 - Left Seat Wall
19 Feed the four hoses and controller cable from the back wall and connect them as shown. The steam hose connectionuses a hose clamp while the other hoses use spring clamps that are on the hoses. Also feed the CD/Radio wire bundle to the back wall. (J-Dream II with stereo only.) J-Dream II Owner's M...
Page 22 - Back Wall
20 J-Dream II Owner's Manual Use cable ties to attach the CD/Radio wire bundle to the cascade hose. The hoses from valves 1 and 3 and the steamhose are loosely attached to their mounting brackets to allow the slack when connecting them and when the hinged seatwall is swung open (like a door) to acce...
Page 24 - Bonding; (top left hand side of right hand equipment seat wall)
22 Bonding (top left hand side of right hand equipment seat wall) J-Dream II Owner's Manual Connect a #8 guage (10mm2) minimum solid copper bond wire to the house electrical pannel or an approvedlocal ground. An approved ground may be an 8 foot long ground rod (3 meter long earth rod), a plate elect...
Page 26 - Attach Front Panels to Unit
24 Attach Front Panels to Unit Remove this screwbefore operation GroundWire Speaker andpower leads B AntennaWire Rear view of CD/radio Screw (2) Tinnerman ® Nuts (pre-installed) FrontPanel B C D D Front Panel Velcro ® Screw (2) L Important: AttachCD/Radio groundwire here Velcro ® B A A C Frame Screw...
Page 27 - Top Cover
25 Place cover on top of unit. Align notch in cover with the corresponding notch in the top metal frame. J-Dream II Owner's Manual Top Cover
Page 29 - Part II: Operating Instructions; CONTROL PANEL; Shower; Cascade; OFF
27 FIGURE 1. CONTROL PANEL AND DISPLAY FIGURE 2. MIXER CONTROL Part II: Operating Instructions CONTROL PANEL System control is provided by the electronic display located inside the shower cabin (see Figure 1) The display is used to start up the five functions of the unit: the shower, the cascade wat...
Page 30 - Maintenance; Routine Maintenance
Starting the Hydromassage The J-Dream allows you to enjoy the benefits of a real hydromassage. The hydromassage is created by thecombined action of 16 water jets (four sets of 4 ). The action of each group of jets is either alternated or pulsed. To start the hydromassage jets, press the JETS button ...
Page 31 - Care and Maintenance of SteamPros
29 Care and Maintenance of SteamPros Maintenance of the Steampros includes flushing and visually inspecting for water leaks. To flush the units: 1. Turn OFF power to the unit. 2. To gain access to the SteamPros, the seat wall (equipment wall) must be swung open. To do so, remove the three screws fro...
Page 32 - Jacuzzi Whirlpool Bath; Troubleshooting Chart
Printed in the U.S.A. Printed on Recycled Paper PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT. ©1997 Jacuzzi Whirlpool Bath K922000 8/13/04 Jacuzzi Whirlpool Bath P.O. Box 702168, Dallas, TX 75370-2168 Service Support: Call (800) 288...
Page 36 - Warranty
RESPONSIBILITIES OF OTHERS Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible for ensuring the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton ...
