Page 2 - IMPORTANT SAFETY INFORMATION
Note: This is a professional grade product. A knowledge of construction techniques, plumbing and electricalinstallation according to codes are required for proper installation and user satisfaction. We recommend thata licensed contractor perform the installation of all Jacuzzi Whirlpool Bath © produ...
Page 4 - DIMENSIONS; BASE SPECIFICATIONS; TOTAL WEIGHT/FLOOR LOADING; SPECIFICATIONS; TOP VIEW
Important: Read complete instructions before beginning installation. Each unit arrives ready for installation, equipped with base, glass and associated hardware.Remove the unit from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Immediately upon re...
Page 5 - ENCLOSURE SPECIFICATIONS
ROUGH-IN REFERENCE Shown is 2 wall left hand base. Right hand opposite. The 3 wall base has tile flange on both sides and back. ENCLOSURE SPECIFICATIONS 48" 27-11/16" TOP VIEW 72" 38-15/16" 36" 1" TILE FLANGE BLOWER MOTOR FOR UNITS WITH AIR AIR LINE FOR UNITS WITH AIR 84"...
Page 6 - COMPONENT IDENTIFICATION
COMPONENT IDENTIFICATION FRONT VIEW SIDE VIEW (2 WALL ONLY ) GLASS SIDE PANEL GLASS DOORS RAIL BRACKET AND COVER CAP (2 WALL ONLY) (2 WALL ONLY) SIDE SUPPORT RAIL CENTER SUPPORT RAIL AIR TOWER WATER TOWER SEAT BASE DOOR POST DOOR POST WATER TOWER WALL POST (2 WALL ONLY) WALL RAIL WALL POST AND JAMB ...
Page 7 - BASE INSTALLATION; DETAIL 1
PRELIMINARY ROUGH-IN The floor structure beneath the unit must be able to support a total weight of the unit and bather(s).Refer to page 2, SPECIFICATIONS, for weight speci-fications. Refer to COMPONENT IDENTIFICATIONon page 4 to help identify parts. STEP 1 Provide an opening in the subfloor no less...
Page 8 - must; INCORRECT; CORRECT; SHIM INSTRUCTIONS
STEP 6 With a large screwdriver and the tool included with the drain, tighten the inside compression nut to seal thedrain pipe connection. After drain is fully installed, testfor proper drainage. If the shower base does not drainproperly, rectify this condition before proceeding withthe installation...
Page 9 - CLEAN UP AFTER BASE INSTALLATION; and warm water clean soiled surfaces.
CLEAN UP AFTER BASE INSTALLATION To avoid dulling and scratching the acrylic surface of the base, never use abrasive cleaners. A mild liquid detergent and warm water clean soiled surfaces. Remove spilled plaster with a wood or plastic edge. Metal tools scratch the surface. Spots left by plaster or g...
Page 10 - TOWERS AND DOORS INSTALLATION; Do not screw jamb and post together; WATER TOWER DETAIL; JAMB AND
TOWERS AND DOORS INSTALLATION THESE INSTRUCTIONS ARE FOR SUMMER RAIN II2 WALL AND 3 WALL UNITS WITH AND WITHOUTAIR FEATURE OPTION. Refer to COMPONENT IDENTIFICATION on page 4 tohelp identify parts. STEP 1 On the 2 wall unit attach the wall jamb to the water tower adjacent to the side wall. Then inse...
Page 11 - Place the center support rail into slot on each tower. If; HOLD DOWN BRACKET DETAIL; stud or blocking using 3 screws provided.
TOWERS AND DOORS INSTALLATION STEP 4 Place the center support rail into slot on each tower. If rail does not readily fit into slots, it may be necessary toloosen the bolts holding towers to base (it may only benecessary to loosen one tower). DO NOT FORCE CENTER RAIL INTO SLOTS. With center support r...
Page 12 - Filling the area marked; DO NOT FILL
TOWERS AND DOORS INSTALLATION 10 Jacuzzi Whirlpool Bath © BZ00000 03/05 GROUT STUD SHIM IF NECESSARY DO NOT FILL CEMENT BOARD TILE SILICONESEALANT 1-1/8" MAXIMUM NO MINIMUM SHOWERBASE CAULKING TILE CEMENTBOARD TILEADHESIVE STUD FLANGE SHIM IFNECESSARYTO FILL GAPSBETWEEN STUDAND FLANGE STUD 1/8&#...
Page 13 - DETAIL A
STEP 9 (2 WALL ONLY) Place the side support rail into the slot on the water tower. Place the short wall rail into the slot on the other water tower. Rotate flat end of short wall rail flush to wall. With rails in position install hold down brackets, but do not tightenscrews. Check water towers for l...
Page 14 - Attach air supply pipe to air tower plumbing.
STEP 10 Two shut-off valves are provided per water tower. To hook up supply lines, unscrew valves from braided line. Using thread sealant, screw each valve to stub out at bottom of tower. Then reconnect braided line using provided gasket.Do not twist or kink supply lines when connecting. Perform thi...
Page 15 - Move the door assembly to the door post on water; SHOWER BASE; Check that the magnetic mouldings on door and air; Install cover cap by sliding over adjusting screw and
TOWERS AND DOORS INSTALLATION STEP 12 Move the door assembly to the door post on water tower and slide the assembly into the door post. Locatethe base of the door into the slot of serrated doorpositioner that positions the hinge barrel as shown. BOTTOM OF DOOR FRAME HINGE BARREL SHOWER BASE WATER TO...
Page 16 - Slide fixed glass panel all the way into wall post.
TOWERS AND DOORS INSTALLATION FINISH WALL EDGEOF BASE GLASS SIDEPANEL MOUNTEDPARALLEL TO EDGE OF BASE WALL POST TAPE (3) SCREWS (3) STEP 15 (2 WALL ONLY) Position the fixed glass wall post so that the glass sidepanel will be parallel with the outside edge of the base.The fixed glass wall post positi...
Page 17 - TOWER AND DOOR INSTALLATION; Align the glass with glass jamb and insert.; NOTE: The glazing is to be installed on the; outside; of; Clean any soapy residue off the glass and towers.
TOWER AND DOOR INSTALLATION STEP 18 (2 WALL ONLY) Align the glass with glass jamb and insert. WALL POST GLASS GLAZING GASKET INSIDE OFENCLOSURE APPLY SEALANT JAMB GLASS GLAZING GASKET INSIDE OFENCLOSURE APPLY SEALANT STEP 19 (2 WALL ONLY) Install glazing gasket on fixed glass wall post and jambs on ...
Page 18 - TOWERS AND DOOR INSTALLATION
STEP 23 Install handles as shown. Note orientation of handle. Hand tighten knob. Flat screw has a screw driver notch.Do not over tighten either knob or flat screw as crackedglass may result. GLASSDOOR WASHERS LARGEWASHER INTERIOR OFSHOWER DOORHINGE TOWER COVER INSERT THIS SIDE FIRST TOWER COVER TOWE...
Page 19 - post, and bottom of glass side panel on the inside only.; CLEAN UP AFTER TOWERS AND DOOR INSTALLATION; Do not use abrasives,; Consult your Jacuzzi Whirlpool Bath
TOWERS AND DOOR INSTALLATION STEP 26 Seal all around all bases of towers with sealant. Also seal the inside of wall posts, jambs, door posts, tile joint to wall post, and bottom of glass side panel on the inside only. CLEAN UP AFTER TOWERS AND DOOR INSTALLATION To avoid dulling and scratching the to...
Page 20 - OPERATION; SHOWER TOWERS; Shower Head; LESS FLOW AND INTENSITY; STOP RELEASE
OPERATION SHOWER TOWERS 18 Jacuzzi Whirlpool Bath © BZ00000 03/05 Shower Head There are three selectable positions: Jet, Normal Pul-sating, and Aerated flow. Body Sprays (2 Upper and 2 Lower) To adjust the flow and intensity, turn as shown. Thespray can also be turned to change the direction of thes...
Page 21 - CONTROLLER; AIR TOWER; AIR FLOW LED; AIR TOWER CONTROLS
OPERATION CONTROLLER To turn ON press ON/OFF button or turn ON water at either shower tower.The unit will then automatically go into a preheat cycle to heat the airtransmission pipes. There will be a 5 (five) minute pause while the systempreheats. During this time both LEDs will be ON. When ready fo...
Page 22 - MAINTENANCE
To remove any lime scale from the shower head and body sprays, rub with your finger the outer ring of nozzles on theshower head and all nozzles on the body spray. To clean the foot temperature tester, unscrew the nozzle and back flush the wire mesh filter. Do not use metal tools(such as scissors or ...
Page 23 - TOWER FIXTURES REPAIR PARTS
TOWER FIXTURES REPAIR PARTS 21 Jacuzzi Whirlpool Bath © BZ00000 03/05 TOWER ASSEMBLY WASHER (PART OF D709827) 4 6 9 (5X) 10 11 (4X) 13 14 15 16 17 18 19 3 (5X) 2 (5X) 1 (5X) 8 5 12 PART OF D709827 7 (PART OF U547000) 1. C546000 Lock Nut, 1/2" NPT WP (5X) 2. G559000 Ring Compression SS (5X) 3. G5...
Page 24 - TOWER PLUMBING REPAIR PARTS
TOWER PLUMBING REPAIR PARTS 1 11 4 5 4 7 10 6 14 12 13 5 4 16 11 2 8 2 3 2 3 3 17 15 9 18 19 18 18 18 ITEMNO. QTY. PART NO. DESCRIPTION 1 1 Y221000 TOWER, 2 PERSON SHOWER 2 3 U401000 FTG, ELL, .50" FST x 10 mm BARB 3 4 Y724000 1/2" ELBOW, SLIP x THREAD, SCH 40 4 3 7164000 ELL, STREET, .50...
Page 26 - Jacuzzi Whirlpool Bath National Headquarters; PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Printed in U.S.A . Jacuzzi Whirlpool Bath © BZ00000 03/05 Printed on Recycled Paper Jacuzzi Whirlpool Bath National Headquarters P.O. Box 702168, Dallas, TX 75370-2168 Service Support: (800) 288-4002 PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. USE INSTALLATION INSTRUCTIONS SUPPLIED ...
Page 27 - WARRANTY COVERAGE; RETURN OF WARRANTY CARD; Jacuzzi Whirlpool Bath Limited Warranty
Jacuzzi Whirlpool Bath P.O. Box 702168Dallas, TX 75370-2168 WARRANTY COVERAGE Jacuzzi Whirlpool Bath (the “Company”) offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Designer Collection Bath Product (“unit”) who purchases the product for personal ...
Page 28 - RESPONSIBILITIES OF OTHERS; WARRANTY SERVICE; Warranty
RESPONSIBILITIES OF OTHERS Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible for ensuring the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton ...
