Husqvarna TS 250 XL - Manual

Page 2 - Part Numbers that have an ASTERISK (*) suffix may not be active 9-digit; CONTENTS

NOTE: Part Numbers that have an ASTERISK (*) suffix may not be active 9-digit numbers. The ‘542’ prefix have been added to current 6-digit part numbers and ‘0’ to 8-digit part numbers. EVERY MACHINE IS THOROUGHLY TESTED BEFORE LEAVING THE FACTORY. EACH MACHINE IS SUPPLIED WITH A COPY OF THIS MANUAL....

Page 5 - WARNING; HEARING HAZARD; ATENCION; RIESGO DE DAÑO AUDITIVO

WARNING HEARING HAZARD DURING NORMAL USE OF THIS MACHINE, OPERATOR MAY BE EXPOSED TO A NOISE LEVEL EQUAL OR SUPERIOR TO 85 dB (A) ATTENZIONE!!! RISCHIO DE LESIONE ALL’APPARATO UDITIVO NELLE NORMALI CONDIZIONI DI UTILIZZO, QUESTA MACCHINA PUÒ COMPORTARE PER L’OPERATORE ADDETTO UN ESPOSIZIONE ACUSTICA...

Page 6 - ETIQUETAS Y SU UBICACIÓN; DUST WARNING; frequently contains silica; California Prop 65 Warning:

542 18 70-43* Location: Top of Belt Guard 542 04 63-26* Location: Motor Assembly 542 18 92-47* Location: Elec. Motor DECALS & LOCATIONS ETIQUETAS Y SU UBICACIÓN AUTOCOLLANTS ET LEURS EMPLACEMENTS DUST WARNING Cutting, especially when DRY cutting, generates dust that comes from the material being...

Page 8 - WARNINGS; DO’s AND DO NOT’s; FAILURE TO COMPLY WITH THESE WARNINGS AND OPERATING; DO

DO read this entire operator’s manual before operating this machine. Understand all warnings, instructions, and controls . DO keep all guards in place and in good condition. DO wear safety approved hearing, eye, head and respiratory protection. DO read and understand all warnings and instructions on...

Page 9 - Husqvarna Construction Products; DO NOT

DO NOT operate this machine unless you have read and understood this operator’s manual. DO NOT operate this machine without the blade guard, or other protective guards in place. DO NOT stand behind or in front of the blade path while the motor is running. DO NOT leave this machine unattended while t...

Page 10 - FIGURE 1; Assembly Component Identification; FIGURE 2

0 FIGURE 1 Assembly Component Identification A. Pan Guides B. Pan Stops C. Drain Plug D. Bearing Cap & Fasteners E. TIle Saw Wrench (15/16” x 9/16” x 1/2”) F. Locking Knob G. Lockbar H. Water Pump J. Hose Barb Fitting K. Water Valve L. Water Tube Assy L1. Fitting End - Tube Assy L2. Plastic Nozz...

Page 11 - Profile Wheel; Features

11 These signs will give advice for your safety Before leaving our factory every machine is thoroughly tested. Follow our instructions strictly and your machine will give you long service in normal operating conditions. I N S T R U C T I O N INDICATION INFORMATION WARNING PROHIBITION Use : Sawing of...

Page 14 - FIGURE 3

Good motor performance depends on proper voltage. Extension cords that are too long and/ or too small in wire gauge reduce the voltage to the motor under load. Use extension cords no smaller than indicated below. The motor is equipped with a manual overload protection reset button. If the motors ove...

Page 16 - WATER PUMP TROUBLE-SHOOTING PROCEDURE; REPAIRS

If Water Stops Flowing , 1. Stop Sawing , then 2. Disconnect Electrical Plug from Outlet , then 3. Remove the Pump , then 4. Back Flush. Back flushing is done by forcing water into the pump discharge and out through the screen. Most of the time this procedure works, and the pump can be put back into...

Page 17 - RIP GUIDE; 5 TILE CUTTING ACCESSORIES

17 The instructions for use and spare parts found in this document are for information only and are not binding. As part of our product quality improvement policy, we reserve the right to make any and all technical modifications without prior notice. The manufacturer accepts no responsibility caused...

Page 21 - Corporate Office

Serial Number: Model Number: Date of Purchase: . . Where Purchased: Please record the Date of Purchase and the Serial Number, the Model Number of the equipment and the Date of Purchase of your equipment in the space below. When ordering service items, please have this information available. NOTE: Mo...

Husqvarna TS 250 XL - Manual

Table of Contents:

Summary

Other Husqvarna Models