Page 2 - Product description
Contents Introduction..................................................................... 2Safety..............................................................................4Assembly...................................................................... 12Operation....................................
Page 4 - Safety; Safety definitions; Work area safety
Note: Other symbols/decals on the product refer to certification requirements for some markets. Symbols on the battery and/or on the battery charger Recycle this product at a recy- cling station for electrical and electronic equipment. (Applies to Europe only) Fail-safe transformer. Use and keep the...
Page 6 - Causes and operator prevention of kickback; General safety instructions
operating chain saws may cause entanglement of your clothing or body with the saw chain. • Always hold the chain saw with your right hand on the top handle and your left hand on the front handle. Holding the chain saw with a reversed hand configuration increases the risk of personal injury and shoul...
Page 7 - Safety instructions for operation
Safety instructions for operation WARNING: Read the warning instructions that follow before you use the product. • The information in this operator's manual not an alternative to professional knowledge and experience. If you do not feel sure about how to operate this product, turn to a person with p...
Page 10 - Battery safety
brake. If a kickback occurs when you use the product, hold tightly around the handles and do not let go. The front hand guard also decreases the risk to touch the saw chain if your hand lets go of the front handle. In the felling position you cannot engage the chain brake manually. The chain brake c...
Page 11 - Safety instructions for the cutting equipment
Battery charger safety WARNING: Read the warning instructions that follow before you use the product. • Risk of electrical shock or short circuit if the safety instructions are not obeyed. • Use an approved grounded mains socket that is not damaged. • Do not use other battery chargers than the one s...
Page 12 - Assembly; To assemble the guide bar and saw
chain and chain drive sprocket. Refer to To adjust the tension of the saw chain on page 24. • Do maintenance on the cutting equipment regularly and keep it correctly lubricated. If the saw chain is not correctly lubricated, the risk of wear on the guide bar, saw chain and chain drive sprocket increa...
Page 13 - Operation; Introduction
9. Tighten the saw chain. See To adjust the tension of the saw chain on page 24 for instructions. Operation Introduction WARNING: Read and understand the safety chapter before you use the product. To do a function check before you use the product 1. Do a check of the chain brake to make sure that it...
Page 14 - Common questions about kickback
To connect the battery to the battery chargerNote: Charge the battery if it is the first time that you use it. A new battery is only 30% charged. 1. Make sure that the battery is dry.2. Put the battery in the battery charger. 3. Make sure that the green charging light on the battery charger comes on...
Page 16 - Ground operator
To stop the product 1. Push and hold the start/stop button until the green LED light comes off. 2. Push the battery release buttons and remove the battery from the battery holder to prevent accidental start. General information about working technique Below we give you some general information about...
Page 17 - Tree operator; To operate the product in a tree
3. Attach the end of an approved safety strop to the rope eyelet. Note: A safety strop makes sure that the product does not hit the ground if it falls. 4. Make sure that there is a carabiner on the other end of the safety strop. 5. Start the product.6. Stop the product.7. Engage the chain brake.8. L...
Page 18 - To remove a trapped product; Maintenance
• Use a foot loop to keep a safe work position. • Do a check of the harness, belt and ropes at a regular interval. • If you must climb with the product, attach the product to the rear connection point on the harness. The rear connection point keeps the product clear from climbing lines and makes sur...
Page 19 - To do a check of the front hand guard
Maintenance Before use Weekly Monthly Make sure that the power trigger and the power trigger lockout function correctly from a safety point of view. X Clean the chain brake and make sure that it operates safely. Make sure that the chain catcher is not damaged. Replace it if necessary. X Turn the gui...
Page 21 - Information about the guide bar and saw chain
3. Make sure that the product stops when you press and hold the button. The green LED will go off. To do a check of the battery and the battery holder 1. Clean the battery and the battery holder with a soft brush. 2. Clean the cooling slots and battery connectors. 3. Make sure that the battery has n...
Page 26 - Troubleshooting; Keypad
4. Examine the groove in the guide bar for wear. Replace the guide bar if it is necessary. 5. Examine if the guide bar tip is rough or very worn. 6. Make sure that the bar tip sprocket turns freely and that the lubricating hole in the bar tip sprocket is not blocked. Clean and lubricate if it is nec...
Page 27 - Battery charger; Transportation, storage and disposal; Transportation and storage
Problem Possible faults Possible solution Red error LED comes on. Cell difference is to much (1V). Speak to your servicing dealer. Battery charger LED display Possible faults Possible action Warning indicator flashing. Temperature deviation. Use the battery in surroundings where temperatures are bet...
Page 28 - Technical data
Technical data Technical data T535i XP Motor Type BLDC (brushless) 36V Features Low energy mode savE Lubrication system Type of oil pump Automatic Oil tank capacity, liter/cm 2 0.20/200 Weight Chainsaw without battery, guide bar, saw chain and empty chain oil tank, kg 2.5 Water protection level IPX4...
Page 29 - Accessories; Guide bar and saw chain combinations
T535i XP Recommended bar lengths, inch/cm 10-14/25-35 Usable cutting length, inch/cm 9-13/23-33 Type of drive sprocket/number of teeth Spur/7 Maximum chain speed / (savE), m/s 20 (15) Accessories Guide bar and saw chain combinations The following cutting attachments are approved for Husqvarna T535i ...
Page 30 - Approved batteries for the product; Approved battery chargers
SP21G 5/32 in / 4.0 mm 60° 30° 0° 0.025 in / 0.65 mm 5950046-01 5950047-01 Approved batteries for the product Battery BLi200 40-B220X Type Lithium-ion Lithium-ion Battery capacity, Ah 5.2 6.0 Nominal voltage, V 36 36 Weight, kg 1.3 1.4 Approved battery chargers Battery charger QC330 Input voltage, V...
Page 31 - Declaration of Conformity; EU Declaration of conformity
Declaration of Conformity EU Declaration of conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Cordless battery chainsaw for tree service Brand Husqvarna Type / Model T535i XP Identification Serial numbers da...
Page 32 - Declaration of conformity
Declaration of conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Cordless battery chainsaw for tree service Brand Husqvarna Type / Model T535i XP Identification Serial numbers dating from 2021 and onwards co...
