Husqvarna ST724 - Manual

Husqvarna ST724

Husqvarna ST724 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
Page: / 40

Table of Contents:

  • Page 2 – SAFETY RULES; IMPORTANT
  • Page 3 – California Proposition 65 WARNING!
  • Page 4 – TABLE OF CONTENTS
  • Page 5 – INTERNATIONAL SYMBOLS
  • Page 16 – ASSEMBLY; CONTENTS OF SHIPPING; - Snow thrower completely assembled except for the; TOOLS REQUIRED FOR
  • Page 17 – TO INSTALL THE CRANK ASSEMBLY; Tighten the eye bolt installed earlier.; III.1 shows the snow thrower in the shipping position.; Remove top pallet from carton.
  • Page 18 – Tighten nuts securely.
  • Page 19 – OPERATION; IMPORTANT: DO NOT MOVE THE SPEED SHIFT
  • Page 20 – TO STOP ENGINE
  • Page 21 – FROZEN STARTER; If the starter is frozen and will not turn engine:; Pull as much rope out of the starter as possible.; SNOW THROWING TIPS; Clean the snow thrower thoroughly after each use.
  • Page 22 – MAINTENANCE; LUBRICATION - EVERY TEN HOURS; Position speed selector lever in first gear.; GENERAL RECOMMENDATIONS; AFTER EACH USE; Check for any loose or damaged parts.; SNOW THROWER; LUBRICATION - EVERY FIVE HOURS
  • Page 23 – SERVICE AND ADJUSTMENTS; TO ADJUST SKID HEIGHT; If adjustment is necessary:; TO ADJUST BELTS
  • Page 24 – TRACTION DRIVE BELT
  • Page 25 – TO ADJUST THE FRICTION WHEEL; TO REPLACE FRICTION WHEEL; To replace a broken shear bolt, proceed as follows:
  • Page 26 – Remove the spark plug wire.; TO ADJUST CARBURETOR; Close the high speed adjusting screw by hand.; IMPORTANT: NEVER TAMPER WITH THE ENGINE
  • Page 27 – STORAGE; OTHER; Thoroughly clean the snow thrower.; ENGINE
  • Page 28 – TROUBLE; TROUBLESHOOTING POINTS
  • Page 29 – ENGINE REPAIR PARTS
  • Page 30 – FRAME REPAIR PARTS
  • Page 31 – DRIVE COMPONENT REPAIR PARTS
  • Page 32 – GEAR BOX REPAIR PARTS
  • Page 33 – AUGER HOUSING REPAIR PARTS
  • Page 34 – DISCHARGE CHUTE REPAIR PARTS
  • Page 35 – WHEEL ASSEMBLY REPAIR PARTS
  • Page 36 – HANDLES REPAIR PARTS
  • Page 37 – CONTROL PANEL REPAIR PARTS
  • Page 38 – DECALS
  • Page 39 – CHUTE CONTROL ROD REPAIR PARTS
  • Page 40 – NOTES
Loading the manual

1.1996

Spare Parts
Piéces Dètachées

Owner's Manual 601 00 17-36
Reference No. 337209 05/09/95

ST724

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - SAFETY RULES; IMPORTANT

2 SAFETY RULES BEFORE USE ● Read the Owner’s Manual carefully. Be thoroughlyfamiliar with the controls and the proper use of the snowthrower. Know how to stop the snow thrower anddisengage the controls quickly. ● Do not operate the snow thrower without wearingadequate winter outer garments. Wear foo...

Page 3 - California Proposition 65 WARNING!

3 LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS. IT MEANS--ATTENTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED. SAFETY RULES SAFE STORAGE ● Always refer to Owner’s Manual instructions for importantdetails if the snow thrower is to be stored for an extendedperiod. ● Disengage power ...

Page 4 - TABLE OF CONTENTS

4 Record the following information about your unit so that you will be able to provide it in case of loss or theft. CITY: STATE: TELEPHONE: PURCHASE DATE: MODEL NUMBER: / / SERIAL NO.: CODE NO.: (Enter complete 8 digit number from model plate on unit) DEALER'S NAME AND ADDRESS: TABLE OF CONTENTS SAF...

Other Husqvarna Models