Page 3 - CONTENTS
3 41277-01 05/98 ® CONTENTS Important Information ....................................................................................................................................... 4 Step 1 - Getting Ready ............................................................................................
Page 4 - IMPORTANT INFORMATION; CAUTIONS
4 41277-01 05/98 ® IMPORTANT INFORMATION DO YOU NEED HELP? To install a ceiling fan, be sure youcan do the following: • Locate ceiling joist or other suit- able support in ceiling. • Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help ...
Page 5 - GATHERING THE TOOLS; OPTIONAL ACCESSORIES; STEP 1 - GETTING READY; PREPARING THE FAN SITE
5 41277-01 05/98 ® GATHERING THE TOOLS You need the following tools to in-stall the fan: • Electric drill with 9/64" bit • Standard screwdriver • Phillips-head screwdriver • Wrench or pliers OPTIONAL ACCESSORIES Consider using Hunter’s optional ac-cessories, such as a wall-mounted orremote speed...
Page 6 - Angle Mounting
6 41277-01 05/98 ® INSTALLER’S CHOICE ® This patented 3-position mountingsystem gives you maximum flexibil-ity and ease of installation. The stepsin this manual include specific in-st ru c t i o n s f o r t h e fan mountingmethod of your choice. For a ceiling8 feet or higher, standard mountingis rec...
Page 7 - For Angle Mounting Only:; STEP 2 - INSTALLING THE CEILING PLATE
7 41277-01 05/98 ® 4. Align the slotted holes in the ceil- ing plate with the pilot holes int h e w o o d s u p p o r t s t r u c t u re . Note: The isolation pads should be flush against the ceiling. 1. Drill two pilot holes into the wood support structure through theoutermost holes on the outletbo...
Page 9 - ALL FANS; STEP 3 - ASSEMBLING THE FAN
9 41277-01 05/98 ® Follow sub-step 1 below for all fans.Then, use the additional instructionsfor the type of mounting you haveselected: flush, standard, or angle. ALL FANS 1. Position the fan housing over the motor hanger adapter. Make surethe tabs in the motor hangeradapter fit into the notches in ...
Page 11 - STEP 4 - WIRING THE FAN
11 41277-01 05/98 ® STEP 4 - WIRING THE FAN 1. Disconnect the power by turning off the circuit breakers to the out-let box and associated wall switchlocation. 2. Tilt and hang the assembled fan from the ceiling plate hooks. Sliptwo rectangular canopy slots overceiling plate hooks as shown inFigures ...
Page 12 - CAUTION
12 41277-01 05/98 ® Figure 4c - Wiring Diagram Bare or Green ApprovedConnectors Power Wires In Ceiling White White Black Black/White 1 2 Connections: Black Wall Switch Wire For Separate Control of Light Kit CeilingPlate Outlet Box 2 x 4 Brace Green GroundWire from HangerPipe (standard and angle moun...
Page 13 - STEP 5 - HANGING THE FAN; WARNING
13 41277-01 05/98 ® STEP 5 - HANGING THE FAN Figure 5a - Attaching Canopy toCeiling Plate Figure 5b - Canopy Tabs and Groovesin Hanger Ball Sub-steps 1 and 2 apply to Flush,Standard, and Angle mounting. Sub-step 3 applies to Standard and Anglemounting only. 1. Swing the fan up so as to align the can...
Page 14 - STEP 6 - ATTACHING BLADE ASSEMBLY
14 41277-01 05/98 ® Figure 6a - Attaching Fan Blade to Speed Ring™ Using Decorative Medallion(Speed Ring™ Positioned Upside Down) STEP 6 - ATTACHING BLADE ASSEMBLY Speed Ring™(PositionedUpside Down) Fan Blade DecorativeMedallion Screw Hunter’s Speed Ring™ (patent pend-ing) system makes installation ...
Page 17 - STEP 7 - ATTACHING LIGHT FIXTURES; WARNINGS
17 41277-01 05/98 ® STEP 7 - ATTACHING LIGHT FIXTURES Figure 7a - Removing Plug Buttonand Switch Housing Cover SwitchHousingCover Plug Button Your Whisperwind 2000™ fan mayinclude a light fixture. You may en-joy the fan with or without the lightfixture. Information for wiring and in-stalling all inc...
Page 19 - All Other Lights
19 41277-01 05/98 ® ATTACHING LIGHT FITTER TOFAN SWITCH HOUSING Low-Profile Lights 1. U n s c r e w t h e t w o # 6 x 1 / 2 " mounting screws to remove thelight fixture cover plate as shownin Figure 7c. Do not discard thescrews. 2. Assemble the switch housing cover to the light fixture housing. ...
Page 20 - AURORA FIXTURES
20 41277-01 05/98 ® Figure 7f - Aurora Fixtures AURORA FIXTURES Refer to Figure 7f.
Page 22 - OPERATING YOUR HUNTER FAN
22 41277-01 05/98 ® OPERATING YOUR HUNTER FAN 1. Turn on electrical power to the fan. 2. The pull chain controls power to the fan. The chain has four set-tings in sequence: High, Medium,Low and Off. • Pull the chain slowly to change settings. • Release slowly to prevent the chain from recoiling into...
Page 23 - TROUBLESHOOTING; PROBLEM
23 41277-01 05/98 ® TROUBLESHOOTING Nothing happens; fan does not move. Noisy operation. 1. Power turned off, fuse blown, or circuit breaker tripped. 2. Loose wire connections or wrong connections. 3. Motor reversing switch not en- gaged. 4. Pull chain switch not “on.” 1. Blade screwed loosely to Sp...