Hunter M0006-01 - Manuals - manualsarea.com

Page 2 - What to Expect with Your Installation; qualified electrician.; Read and Save These Instructions; WARNINGS; CAUTIONS; Standard Downrod

www.HunterFan.com 1.888.830.1326 M0006-01 • 04/14/14 • © Hunter Fan Company 1.888.830.1326 1.888.830.1326 What to Expect with Your Installation Know your wiring If you are unfamiliar with wiring, use a qualified electrician. You may need a friend to help you. Check box to see fan weight Assess locat...

Page 3 - Tools Needed; Ladder

www.HunterFan.com 1.888.830.1326 Tools Needed Ladder Power Drill (optional) 9/64” Drill Bit (optional) Screwdrivers Pliers Wire Strippers If mounting to a support structure, you will also need these tools. 3 M0006-01 • 04/14/14 • © Hunter Fan Company

Page 4 - TU; Mounting Options; Use; Standard Mounting; or; Angled Mounting; to hang the fan from a; OPTION; OPTION; SLIDE; PLACE; FOLD

www.HunterFan.com 1.888.830.1326 If you have an angled ceiling: 1. You will need a longer downrod (sold separately) . 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately) . Guide Touches BOTH Ceiling & Wall SI TU AT IO N 1 Guide Touches Wall b...

Page 5 - Ceiling Bracket; OFF; For angled ceilings, point; Turn P; bumpers are still attached.

www.HunterFan.com 1.888.830.1326 Ceiling Bracket OFF For angled ceilings, point opening toward peak. Refer to warning w.1 on pg. 2 If you are unable to do this, call Technical Support at 1-888-830-1326. Use wood screws (included) when securing to support structure with approved electrical outlet box...

Page 6 - Downrod; Slid; Option 1; skip to next page; If you need a different downrod length follow these steps:; Steps 1-5 to remove standard downrod pipe; new; pipe

www.HunterFan.com 1.888.830.1326 6 M0006-01 • 04/14/14 • © Hunter Fan Company Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 Sold S epar at ely Included Longer Downrod for angled ceilings or ceilings 10’ or higher Shorter Downrod for fans installed close to ceiling Standard Downrod for ceilings 8-10’ hi...

Page 7 - DO NOT

www.HunterFan.com 1.888.830.1326 7 M0006-01 • 04/14/14 • © Hunter Fan Company KEEP! 8” 3/8” CU T & ST R IP (not to scale) Remove the pre-installed setscrew so that the downrod can be inserted. Hand tighten the downrod (at least 4-5 full turns) until it stops. The wires can be cut, but leave at l...

Page 8 - DO NOT PICK THE FAN UP BY THE; Place the downrod

www.HunterFan.com 1.888.830.1326 Downrod (continued) DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. 8 M0006-01 • 04/14/14 • © Hunter Fan Company

Page 9 - Wiring; For Dual Switches

www.HunterFan.com 1.888.830.1326 Wiring F RO M F A N F RO M CE IL ING BR A CK E T F R O M F A N Using an orange wire connector from the hardware bag, connect the 3 grounding wires (green, green/ yellow stripe, or bare copper) coming from the ceiling, downrod, and hanging bracket. (G rounding) G reen...

Page 10 - Canopy; lifted into place, the canopy fits into; Screw

www.HunterFan.com 1.888.830.1326 Canopy Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Note: Fan style may vary. Lift the canopy into place so that the screw holes are aligned. Screw Holes Insert the two canopy screws found in the hardware bag...

Page 11 - Blades; Align the three holes in the blade with the; Blade

www.HunterFan.com 1.888.830.1326 Blades Align the three holes in the blade with the three blade iron posts. Squeeze the blade and the blade post together. The flared tops of the blade iron posts will be fully visible above the blade when properly assembled. Your blades are shielded with Dust Armor® ...

Page 12 - Light Kit; Want to install your fan without a light kit?

www.HunterFan.com 1.888.830.1326 12 M0006-01 • 04/14/14 • © Hunter Fan Company Partially install two of the switch housing screws found in the bag. Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. Align the notches in the sides ...

Page 13 - Note: Glass shade style and number of lights may vary.; To install the shade, first loosen; Shade

www.HunterFan.com 1.888.830.1326 Light Kit (continued) CONGRATULATIONS! YOU’RE DONE! Note: Glass shade style and number of lights may vary. See next page for fan operation instructions. Connect a pull chain pendant to each of the short chains coming from the switch housing. To install the shade, fir...

Page 14 - Maintenance & Cleaning; ON; may damage the finishes.

www.HunterFan.com 1.888.830.1326 Maintenance & Cleaning ON Turn P ow er For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes. To switch the direction of air flow, move the reverse switch to the opposite position. Reverse Switch The fan...

Page 15 - Troubleshooting; Excessive wobbling; firmly left or right to ensure that

www.HunterFan.com 1.888.830.1326 Troubleshooting Excessive wobbling • Make sure that the blades are properly installed on the blade iron posts. • Turn the power off, suppor t the fan carefully, and check that the hanger ball is properly seated. • Use the provided balancing k it and instructions to b...