Hunter 42411-01 - Manuals - manualsarea.com

Page 2 - Cautions and Warnings; • To avoid possible electrical shock, before installing your fan,; Welc om e

Your new Hunter ® ceiling fan is an addition to your home or office that will provide comfort and performance for many years. This installation and operation manual gives you complete instructions for installing and operating your fan. We are proud of our work. We appreciate the opportunity to suppl...

Page 3 - Inst al ler’s Choice and O ptional Ac ce ss orie s; Understanding Mounting and Installer’s Choice

Inst al ler’s Choice and O ptional Ac ce ss orie s Understanding Mounting and Installer’s Choice ® Hunter’s patented 3-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of three ways, depending on ceiling height and your preferenc...

Page 4 - • Gettin g R eady; To install a ceiling fan, be sure you can do the following:; Gathering the Tools; You will need the following tools for installing the fan:; Checking Your Fan Parts; Installing Multiple Fans?

1 • Gettin g R eady To install a ceiling fan, be sure you can do the following: • Locate the ceiling joist or other suitable support in ceiling.• Drill holes for and install wood screws.• Identify and connect electrical wires.• Lift 40 pounds. If you need help installing the fan, your Hunter fan dea...

Page 5 - • Inst al lin g th e C ei lin g Pl at e

2 • Inst al lin g th e C ei lin g Pl at e 2-1. Drill two pilot holes into the wood support structure through the outermost holes in the outlet box. The pilot holes should be 9/64” in diameter. 2-2. Your fan comes with two neoprene noise isolators (“Isolators”). Position the isolators between the cei...

Page 6 - • A ssemblin g and Han g in g th e Fan

Steps 3-1 – 3-2 Steps 3-3 – 3-4 3 • A ssemblin g and Han g in g th e Fan Low Profile Washer Downrod Canopy Set Screw #8-32 x 3/4” Screw Step 3-5 Canopy Slots You can assemble your fan for standard mounting (steps 3-1 – 3-2) or for low profile mounting (steps 3-3 – 3-4). 3-1. To assemble fan to hang ...

Page 7 - • Se c urin g Fan to Se c ond ar y Supp or t Sy st em

4 • Se c urin g Fan to Se c ond ar y Supp or t Sy st em 4-1. Find the looped end of the braided cable and insert it through the ceiling plate and one of the holes in the outlet box into the ceiling. 4-2. Access the support brace in the ceiling. You may not be able to do this from below the ceiling d...

Page 8 - OR; • Wirin g th e Fan

Wire Nut Step 5-3 Step 5-4 All wiring must be in accordance with national and local electrical codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician. Wall switches are not included. Select an acceptable general-use switch in accordance with national and local electri...

Page 9 - • Inst al lin g th e C anopy; -1. Rotate the hanger ball so the tab in the canopy is secure in the; -2. Lift the fan and align the canopy screw holes with the mounting

6 • Inst al lin g th e C anopy 6-1. Rotate the hanger ball so the tab in the canopy is secure in the groove in the hanger ball. WARNING: Failure to complete this step could cause fan to fall. 6-2. Lift the fan and align the canopy screw holes with the mounting holes on the ceiling plate. 6-3. Partia...

Page 10 - • A ssemblin g th e Bl ade s; insert them by hand into the holes on the blades.

10 7 • A ssemblin g th e Bl ade s Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan). 7-1. Your fan may include blade grommets. If your fan has grommets, insert them by hand into the holes on the blades. 7-2. Attach each blade to a blade iron using three blad...

Page 11 - • Inst al lin g th e Li g ht Kit

11 8 • Inst al lin g th e Li g ht Kit WARNING: Use only the light fixture supplied with this fan model. 8-1. To attach the upper switch housing, partially install two housing assembly screws into the switch housing mounting plate. 8-2. Feed the upper plug connector through the center opening of the ...

Page 12 - • Inst al lin g th e Li g ht Kit (Continu ed); of each glass shade. Insert each glass shade in a shade cup.

1 8 • Inst al lin g th e Li g ht Kit (Continu ed) 8-7. To install the glass shades. Place the silencer band around the neck of each glass shade. Insert each glass shade in a shade cup. 8-8. Install and tighten the three thumb screws. Do not overtighten.8-9. Install candelabra light bulbs (60 watt ma...

Page 13 - • O p eratin g and Cleanin g Your C ei lin g Fan; • The chain uses a breakaway connector that separates if the; To Change Airflow Direction

1 9 • O p eratin g and Cleanin g Your C ei lin g Fan 9-1. Turn on electrical power to the fan.9-2. The fan pull chain controls power to the fan. The pull chain has four settings in sequence: High, Medium, Low and Off. • Pull the chain slowly to change settings.• Release slowly to prevent the chain f...

Page 14 - 0 • Trouble sho otin g; plate and in the upper and lower switch housing.

1 10 • Trouble sho otin g Problem: Nothing happens; fan does not move. 1. Turn power on, replace fuse, or reset breaker.2. Loosen canopy, check all connections according to the wiring the fan section. 3. Check the plug connection in the switch housing.4. Push motor reversing switch firmly left or ri...