Hunter MB519-01 - Manual - manualsarea.com

Page 3 - Ladder; Table of Contents; and performance in your home or office for

www.HunterFanInternational.com PAG E 12 PAG E 5 30 inches 7 feet PAG E 2 What to Expect with Your Installation Ceiling Bracket Ladder PAG E 3 Tools Needed Maintenance & Cleaning Troubleshooting Switch Housing Light Kit Table of Contents PAG E 6 PAG E 9 Wiring Canopy Downrod PAG E 10 Blades PAG E...

Page 4 - What to Expect with Your Installation; qualified electrician.; Standard Downrod; Read and Save These Instructions; WARNINGS; CAUTIONS

www.HunterFanInternational.com MB519-01 • 03/13/15 • © Hunter Fan Company What to Expect with Your Installation 2 Know your wiring If you are unfamiliar with wiring, use a qualified electrician. You may need a friend to help you. Check box to see fan weight Assess ceiling angle Ceiling angles greate...

Page 5 - Tools Needed

www.HunterFanInternational.com Tools Needed Ladder Power Drill (optional) 9/64” Drill Bit (optional) Screwdrivers Pliers Wire Strippers If mounting to a support structure, you will also need these tools. 3 MB519-01 • 03/13/15 • © Hunter Fan Company

Page 6 - TU; TU; Mounting Options; Use; Standard Mounting; or; Angled Mounting; to hang the fan from a; OPTION; SLIDE; PLACE; FOLD

www.HunterFanInternational.com If you have an angled ceiling: 1. You will need a longer downrod (sold separately) . 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately) . Guide Touches BOTH Ceiling & Wall SI TU AT IO N 1 Guide Touches Wall but...

Page 7 - Ceiling Bracket; For angled ceilings, point; OFF; Turn P

www.HunterFanInternational.com Ceiling Bracket Refer to warning w.1 on pg. 2 To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location. For angled ceilings, point opening toward ...

Page 8 - Downrod; Slid; Longer Downrod; for angled; Shorter Downrod; for fans installed; Option 1; skip to next page; If you need a different downrod length follow these steps:; Steps 1-5 to remove standard downrod pipe; new; pipe

6 Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 Sold S epar at ely Included Longer Downrod for angled ceilings or ceilings 3 m (10’) or higher Shorter Downrod for fans installed close to ceiling Standard Downrod for ceilings 2,4-3 m (8-10’) high Option 1 Option 2 Option 3 skip to next page If you need ...

Page 9 - DO NOT

7 KEEP! 20 cm (8”) 1 cm (3/8”) CU T & ST R IP (not to scale) Remove the pre-installed setscrew so that the downrod can be inserted. Hand tighten the downrod (at least 4-5 full turns) until it stops. The wires can be cut, but leave at least 8” extending from the top of the downrod. Downrod (conti...

Page 10 - DO NOT PICK THE FAN UP BY THE CANOPY; Place the downrod ball into the slot

www.HunterFanInternational.com Downrod (continued) DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. 8 MB519-01 • 03/13/15 • © Hunter Fan Company

Page 11 - Wiring; For Dual Switches

www.HunterFanInternational.com Wiring F RO M F A N F RO M CE IL ING BR A CK E T F R O M F A N Using an orange wire connector from the hardware bag, connect the 3 grounding wires (green, green/yellow stripe, or bare copper) coming from the ceiling, downrod, and hanging bracket. (G rounding) G reen/Y ...

Page 12 - Canopy; lifted into place, the canopy fits into; Screw

www.HunterFanInternational.com Canopy Lift the canopy into place so that the screw holes are aligned. Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Screw Holes Insert the two canopy screws found in the hardware bag. 10 MB519-01 • 03/13/15 • ©...

Page 13 - Blades

www.HunterFanInternational.com Blades 11 Put the blade washers, found in the hardware bag, onto the blade screws, found in the hardware bag. Then install the blade screws to secure each blade to a blade iron. 11 Lightly attach the blade irons to the motor with screws found in the hardware bag, then ...

Page 14 - Switch Housing

www.HunterFanInternational.com Make sure the upper switch housing is securely attached to the mounting plate. Failure to properly secure all 3 assembly screws could result in the switch housing fixture falling. Switch Housing Feed the wire plug through the center hole of the upper switch housing, th...

Page 15 - Light Kit

13 Light Kit Partially install two of the light kit assembly screws, found in the hardware bag, into the upper switch housing. Lift the light kit assembly and connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. Align the keyhole sl...

Page 17 - Thumbscrew

www.HunterFanInternational.com Light Kit (continued) CONGRATULATIONS! YOU’RE DONE! See next page for fan operation instructions. To attach the outer glass, install the thumbscrews and tighten securely. Connect the appropriate pull chain pendant to each of the short chains. The fan pull chain control...

Page 18 - Maintenance & Cleaning; ON; Changing the direction of air; - unscrew the finial and; Cleaning the fan; may damage the finishes.; Changing the bulbs; the finial and remove it from the

www.HunterFanInternational.com Maintenance & Cleaning ON Turn P ow er Changing the direction of air flow - unscrew the finial and remove it from the threaded rod. Remove the finial cap and unscrew the globe keeper while supporting the inner glass with your other hand. Carefully remove the inner ...

Page 19 - Troubleshooting; Excessive wobbling; firmly left or right to ensure that

www.HunterFanInternational.com Troubleshooting Excessive wobbling • Tighten all of the blade and blade iron screws until they are snug. • Turn the power off, suppor t the fan carefully, and check that the hanger ball is properly seated. • Use the provided balancing k it and instructions to balance t...

Hunter MB519-01 - Manual

Table of Contents:

Summary

Other Hunter Models