Page 2 - Table of Contents; SAFETY INSTRUCTIONS; Read & Save These Instructions; WARNING
42727-01 Table of Contents Safety Instructions .......................................................... 2 Garage Fan Components ................................................... 4 Site Selection & Preparation ............................................. 4 Installation & Operation .........
Page 4 - Garage Fan Components; NOTE; Site Selection & preparation
Garage Fan Components 42727-01 NOTE: Your Garage Fan is intended for mounting at the intersec- tion of a joist and two braces. See Figure 1. If the location you’ve selected does not have such a configuration, then securely install two pieces of framing material between the joists to form the intesec...
Page 5 - Site Selection and preparation; Ceiling Mount; Figure 1; Installation & operation
Site Selection and preparation 42727-01 Ceiling Mount 1. Use the four provided Mounting Screws to secure the Mounting Flange/Downrod Assembly to two intersecting joists. Refer to Site Selection & Preparation, pg. 4. See Figure 1. NOTE: For clarity, ceiling drywall or sheetrock has been omitted. ...
Page 6 - Push the entire Adjustable Leg/Stationary Leg Assembly back so; Figure 2; Move the Leg Adjust Lever toward the front of the fan, then tilt
Installation & operation 42727-01 3. Push the entire Adjustable Leg/Stationary Leg Assembly back so the Stationary Split Sleeve clears the top of the fan. Figure 2 2. Move the Leg Adjust Lever toward the front of the fan, then tilt back the Adjustable Leg. See Figure 2. Leg Adjust Lever
Page 7 - Figure 3a
Installation & operation 42727-01 Figure 3a Figure 3b Figure 3c Stationary Leg 4. Grasp the Stationary Leg and position the Stationary Leg Split Sleeve onto the Downrod, over the Downrod Cup. See Figure 3a. While maintaining your grasp on the Stationary Leg, bring the Ad- justable Leg forward, p...
Page 8 - Figure 4; Figure 5
Installation & operation 42727-01 7. Use the Speed Control Knob to select your fan’s speed. See Figure 4. Off Low Medium High Figure 4 Snake Lamp Switch 8. While your Garage Fan is mounted to the ceiling, you can turn it and tilt it to direct the airflow. To turn the fan, raise the fan so the Sp...
Page 9 - Figure 6; Horizontal Surface Use
Installation & operation 42727-01 Figure 6 Horizontal Surface Use 1. Tilt the fan so the top of the fan clears the Downrod Cup. 2. Lift the fan so the Split Sleeve clears the Downrod Cup. Move the Leg Adjust Lever toward the front of the fan, then tilt back the Adjustable Leg. See Figure 2. 3. R...
Page 10 - Maintenance; CLEANING THE GRILLES AND BLADES:
Maintenance 10 42727-01 CLEANING THE GRILLES AND BLADES: 1. Turn the fan off and remove the plug from the electrical outlet. 2. Remove the Front Grille (with the Hunter logo plate) by removing the eight screws that hold it to the Fan. 3. The Grilles and the Blade Assembly may be cleaned with a damp ...
Page 11 - Troubleshooting; PROBLEM
11 Troubleshooting 42727-01 PROBLEM • Garage Fan will not work. SOLUTION • Make sure the Garage Fan is properly plugged in and the electrical outlet has power. • The Power Cord may be damaged. Inspect the Power Cord. If the Power Cord is damaged, contact a qualified repair person. PROBLEM • Can not ...
Page 13 - LEA Y GUARDE ESTAS INSTRUCCIONES
www.hunterfan.com Modelo 9020X Ventilador para garaje Jetstream 42727-02 LEA Y GUARDE ESTAS INSTRUCCIONES 04/25/2007 13 Es pa ñ o l
Page 14 - Tabla de contenido; Uso en superficie horizontal; PRECAUCIÓN; lea y guarde estas instrucciones
42727-02 Tabla de contenido Instrucciones de seguridad .............................................. 2 Componentes del ventilador para garaje ........................... 4 Selección y preparación del sitio ....................................... 4 Instalación y operación ..............................
Page 17 - Instalación y operación; Figura 1; Montaje en techo; Use los cuatro tornillos de montaje incluidos para asegurar el; selección y preparación del sitio
Instalación y operación Figura 1 Montaje en techo 1. Use los cuatro tornillos de montaje incluidos para asegurar el conjunto de varilla y brida para montaje a dos vigas entrecruza - das. Consulte la página sobre Selección y preparación del sitio 4. Vea la Figura 1. NOTA: Para mayor claridad, se ha o...
Page 18 - Figura 2; Mueva la palanca de ajuste de soporte hacia la parte frontal del
Instalación y operación 42727-02 18 Figura 2 2. Mueva la palanca de ajuste de soporte hacia la parte frontal del ventilador, luego incline hacia atrás el soporte ajustable. Vea la Figura 2. Palanca de ajuste de soporte
Page 19 - Figura 3a
Instalación y operación 42727-02 Figura 3a Figura 3b Figura 3c 3. Presione el soporte estacionario hacia atrás de manera que el manguito separado estacionario despeje la parte superior del ven - tilador. 4. Tome el soporte estacionario y coloque el manguito separado del soporte estacionario en la va...
Page 20 - PARA MODELOS CON LÁMPARA DE BRAZO FLEXIBLE - Ubique la
Instalación y operación 42727-02 9. PARA MODELOS CON LÁMPARA DE BRAZO FLEXIBLE - Ubique la lámpara flexible para iluminar su área de trabajo. Use el interruptor de la lámpara flexible para encender y apagar la lámpara. Vea la Figura 5. Figura 5 Interruptor de la lámpara flexible 20 7. Use la perilla...
Page 22 - Mantenimiento; LIMPIEZA DE LAS REJILLAS Y ASPAS:; los ocho tornillos que la sostienen al ventilador.
Mantenimiento 42727-02 LIMPIEZA DE LAS REJILLAS Y ASPAS: 1. Apague el ventilador y desconéctelo de la toma de corriente. 2. Retire la rejilla delantera (con la placa del logotipo Hunter) retirando los ocho tornillos que la sostienen al ventilador. Este ventilador está lubricado permanentemente y no ...
Page 23 - PROBLEMA; localización de fallas
Mantenimiento 42727-02 PROBLEMA • El ventilador para garaje no funciona. SOLUCIÓN • Asegúrese que el ventilador para garaje se encuentre debidamente conectado y que la toma de corriente funcione. • El cordón de alimentación podría estar dañado. Verifique el cordón de alimentación. Si el cordón de al...