Hunter 44200 - Manual

This thermostat is designed to optimize the use of your heating and cooling equipment. Itdoes this by matching your comfort (the temperatures in your home) to your schedule. An example: 6am – You wake up. Program 1 has the heat set to 70° (21°C). 7:30am – You leave for work. The second program turns...

6-7 Features Manual switch for turning on heating andcooling system. Manual switch forautomatic or continuousfan operation. Battery door for easy access Soft touch programmingbuttons (see below) Display shows time, day, temperature, program number,hold, usage and low battery indicators. Reset button...

This thermostat comes with two #8 slotted screws and two wall anchors for mounting. Toinstall your unit, you should have the following tools and materials. ■ Slotted screwdriver ■ Electric drill and 3/16" bit ■ Hammer ■ Two 1.5V (AA) Size Alkaline batteries CAUTION: Do not remove any wiring from...

■ Each wire coming from the wall to the existing thermostat is connected to a terminal point onthat thermostat. Each of these terminal points is usually marked with a code letter as shown inTable A on page 11. ■ The number of wires in your system can be as few as two (for heat only systems), as many...

Wire Labeling RH G Y W RC RH RH RC RC G G Y Y W W and connect to thermostatTerminal shown then mark wire with label shown If the code letter on yourexisting thermostat is RH, R,VR or 4 24 Volt G or FFan RC, VC24 Volt Cool Y, C or M (See Note)Air Conditioning W or HHeating RED BLUE GREEN YELLOW WHITE...

Snap open the wallplate from your thermostat by pressing the release tab on the bottom ofthe thermostat. Position wallplate on wall and pull existing wires through large opening. Then level forappearance. Mark holes for plastic anchors provided if existing holes do not line up withHunter Thermostat ...

The heating system selector and the F°/C° selector switches are located on the PrintedCircuit Board. ■ Heating system selector The heating system selector is a switch on the Printed Circuit Board on the inside of thethermostat. The switch is at “HG” position. Leave it in this position if you have a ...

Programming 1 Remove mylar label covering displaywindow. 2 When the heating or cooling system isactually operating, “HEAT” or “COOL” will appear on the display. 3 If power is interrupted the batteries willkeep all programs. 4 If “LOW BATT” indicator appears on thedisplay replace the batteries. Setti...

Programming 18-19 Studies conducted by the Department ofEnergy estimate that setting your thermostatback 10°F for two 8-hour periods duringwinter can reduce your fuel bill by as muchas 30%. By setting your thermostat up 5° fortwo 8-hour periods during summer you canreduce your fuel bill up to 25%. Y...

NOTE: The thermostat program will NOTtake effect immediately afterprogramming of your thermostat but atthe next programmed time/temperaturechange. The thermostat is pre-set to 68°F(20°C) for heat and 78°F (25°C) for airconditioning. So if you want atemperature other than 68°F or 78°F (20°C or 25°C) ...

Programming Before programming or changing theprogram, use this Personal Program Scheduleto determine which times and temperaturesettings will best satisfy both your comfortand energy saving requirements. Use a pencil so you can revise your recordseach time you change your temperaturesettings. Perso...

Your thermostat can be programmed in twodifferent ways.1. Auto-program method2. Manual method Before programming, position the Heat/ACselector to the type of program desired. Auto-program method In auto-program method, you can programyour thermostat instantly for the entire weekby simply pressing “A...

Programming WeekdayPrograms Step 1 Step 2 ■ Normal display of time, temper-ature, and day of the week. ■ Program indicator (1) is displayed. ■ 68°F is displayed. ■ 0:00 space for time is displayed. ■ M to F is displayed. PROG M T W TH F SA SU SET TEMP HOLD TEMP 8 9 : 1 5 7 2 c AM PM HEAT COOL 1 2 3 ...

Step 3 ContinueforWeekendPrograms ■ Press on once to changetemperature to 69°F. ■ Weekday program 1 is complete. ■ Press PROG to move to program2, 3, and 4 and follow the samesteps Press to move to weekend programs. Weekends canbe programmed with one schedule,or different schedules for Saturdayand S...

Programming WeekdayProgram ■ Normal display of current time,temperature, and day of week. ■ 1st weekday program is displayed. ■ Program indicator (1) appears. ■ M to F indication appears. PROG PROG M T W TH F SA SU SET TEMP HOLD TEMP 8 9 : 1 5 7 2 c AM PM HEAT COOL 1 2 3 4 FILTER LO BAT M T W TH F S...

To Review The Current Temperature Setting: Press for 2secondsor less: or ■ Current time and temperature M T W TH F SA SU SET TEMP HOLD TEMP 8 9 : 1 5 6 8 c AM PM HEAT COOL 1 2 3 4 FILTER LO BAT ■ 70 indicates the current setting of the thermostat is 70°F. 68 showsthe present room temperature as68°F....

Programming ■ Press arrow to display currentset and room temperatures. M T W TH F SA SU 8 9 : 6 8 6 0 c AMPM HEAT COOL 1 2 3 4 FILTER LO BAT M T W TH F SA SU SET TEMP HOLD TEMP 8 9 : 7 0 6 0 c AMPM HEAT COOL 1 2 3 4 FILTER LO BAT Temporary Manual Override In the following example, the present room t...

In the event you wish to hold your manualoverride for vacation or just an extended period of time, follow the temporary manualoverride instructions on page 26, then immediately press HOLD/CLEAR. This will maintain overridesetting indefinitely. “HOLD” willappear on the display. ■ To return immediatel...

Press Your thermostat comes with an electrolumi-nescent lamp for easy viewing of the displayin the dark. To activate press the “light”button between the up and down arrow keys. The display will remain backlit forapproximately five (5) seconds. If anotherbutton is pushed, the five second timer willre...

Operations 7 2 . 7 I . 7 0 . Your thermostat also keeps a record of thenumber of hours your filter has been in use.To maximize energy efficienty, change orclean your filter regularly.To help you remember, at 500 hours, theword “FILTER” will appear on the display,reminding you to change the filter an...

Troubleshooting Problem Solution SCRAMBLED OR DOUBLE DISPLAY(numbers over numbers NO DISPLAY ENTIRE DISPLAY DIMS PROGRAM DOES NOT CHANGE AT YOURDESIRED SETTING AUTO/FAN DOES NOT COME ON 1. Remove clear mylar sticker. 1. Check battery connections and batteries.2. Press reset button once with a small ...

HEATING OR COOLING DOES NOT GOON OR OFF ERRATIC DISPLAY IF UNIT CONTINUES TO OPERATE IN OFFPOSITION THERMOSTAT READS , HI, LOPERMANENTLY 1. Check that function switch is in correct position (“HEAT” or “COOL”). 2. There may be as much as 20 seconds delay in the thermostat turning the systemon - wait ...

32-33 Wiring Diagrams 4-wire Heat/Cool System 5-wire Heat/Cool System THERMOSTAT G W Y RH RC Heat Relay or Valve Heat/Cool Transformer Fan Relay Cool Contactor Jumper THERMOSTAT G W Y RH RC Heat Relay or Valve Heat Transformer Fan Relay Cool Contactor Cool Transformer