Page 2 - Other Quality Products from Hunter; Fans
Other Quality Products from Hunter Fans Air Purifiers Humidifiers
Page 3 - Table Of Contents; Installation
We are pleased you have selected one of our broad line of home comfort products. Ourproducts are manufactured to high quality standards and are designed for years of service. We hope you will be satisfied and thank you for buying a Hunter product. Table Of Contents Installation Operation Features 6 ...
Page 4 - Read This Before Installing Thermostat; install or operate your Hunter Thermostat.
Read This Before Installing Thermostat IMPORTANT 1 Read the entire installation section of thisOwner’s Manual thoroughly before you begin to install or operate your Hunter Thermostat. • Remove the mylar label from the displaywindow. INSTALLATION 2 All installation is normally performed at yourthermo...
Page 5 - to save energy while you are under the blankets.; How This Thermostat Works...And Saves You Money; BATTERY WARNING; If you plan to be away from the premises
This thermostat is designed to optimize the use of your heating and cooling equipment. It doesthis by matching your comfort (the temperatures in your home) to your schedule. An example: 6am – You wake up. Program 1 has the heat set to 70° (21°C). 7:30am – You leave for work. The second program turns...
Page 6 - Features; Battery door for easy access
6-7 Features Manual switch for turning on heating andcooling system. Manual switch forautomatic or continuousfan operation. Battery door for easy access Soft touch programmingbuttons (see below) Display shows time, day, temperature, program number,hold, usage and low battery indicator. Reset button ...
Page 11 - Wire Labeling; RH
Page 13 - Mount Wallplate and Thermostat; Figure 2
Snap open the wallplate from your thermostat by pressing the release tab on the bottom ofthe thermostat. Position wallplate on wall and pull existing wires through large opening. Then level forappearance. Mark holes for plastic anchors provided if existing holes do not line up withHunter Thermostat ...
Page 14 - Heating system selector; Selector Switches
The heating system selector and the F°/C° selector switches are located on the Printed CircuitBoard. ■ Heating system selector The heating system selector is a switch on the Printed Circuit Board on the inside of thethermostat. The switch is at “HG” position. Leave it in this position if you have a ...
Page 15 - The LCD display indicates the current room
FIGURE 3 FIGURE 4 W RC RH Y G ■ Be sure to tighten the terminal screws securely, otherwise a loose wire could cause operationalproblems with your system or thermostat. ■ Push excess wire back into hole to prevent interference with mounting of the thermostat cover. ■ Make sure the Function Switch is ...
Page 16 - Programming; appear on the display.; Setting the Time and Day of Week; Current room temperature is 72°.
Programming 1 Remove mylar label covering displaywindow. 2 When the heating or cooling system isactually operating, “HEAT” or “COOL” will appear on the display. 3 If power is interrupted the batteries willkeep all programs. 4 If “LOW BATT” indicator appears on thedisplay replace the batteries. Setti...
Page 18 - A typical set of programs is shown in Table 1.; Weekday Program; Winter; Winter; PM; PM
Programming Studies conducted by the Department ofEnergy estimate that setting your thermostatback 10°F for two 8-hour periods duringwinter can reduce your fuel bill by as muchas 30%. By setting your thermostat up 5° fortwo 8-hour periods during summer you canreduce your fuel bill up to 25%. Your th...
Page 19 - Weekend Program
NOTE: The thermostat program will NOTtake effect immediately afterprogramming of your thermostat but atthe next programmed time/temperaturechange. The thermostat is pre-set to 68°F(20°C) for heat and 78°F (25°C) for airconditioning. So if you want atemperature other than 68°F or 78°F (20°Cor 25°C) r...
Page 20 - Personal Program Schedule; FOR WINTER
Programming Before programming or changing the program,use this Personal Program Schedule todetermine which times and temperaturesettings will best satisfy both your comfort andenergy saving requirements. Use a pencil so you can revise your recordseach time you change your temperaturesettings. Perso...
Page 21 - Autoprogram method; Press; Manual method; Programming Your Thermostat; TIME; TABLE 3
Your thermostat can be programmed in twodifferent ways.1. Autoprogram method2. Manual method Before programming, position theHeat/Off/Cool selector to the mode to beprogrammed. Autoprogram method In autoprogram method, you can programyour thermostat instantly for the entire weekby simply pressing “A...
Page 22 - Weekday Program 1 is complete.; increments of 15 minutes.
Programming WeekdayPrograms Step 1 Step 2 ■ Normal display of time, temper-ature, and day of the week. ■ Program indicator (1) is displayed. ■ 68°F is displayed. ■ 0:00 space for time is displayed. ■ M to F is displayed. PROG M T W TH F SA SU SET TEMP HOLD TEMP 8 9 : 1 5 7 2 c AM PM HEAT COOL 1 2 3 ...
Page 23 - Use; Similar to weekday programming.
Step 3 ContinueforWeekendPrograms ■ Press on once to changetemperature to 69°F. ■ Weekday program 1 is complete. ■ Press PROG to move to program2, 3, and 4 and follow the samesteps Press to move to weekend programs. Weekends canbe programmed with one schedule,or different schedules for Saturdayand S...
Page 24 - st weekday program is displayed.; Reviewing Programs; Continue pressing
Programming WeekdayProgram ■ Normal display of current time,temperature, and day of week. ■ 1st weekday program is displayed. ■ Program indicator (1) appears. ■ M to F indication appears. PROG PROG M T W TH F SA SU SET TEMP HOLD TEMP 8 9 : 1 5 7 2 c AM PM HEAT COOL 1 2 3 4 FILTER LO BAT M T W TH F S...
Page 25 - To Review The Current Temperature Setting:; or; 0 indicates the current setting of; Temporary Manual Override of Program
To Review The Current Temperature Setting: Press for 2secondsor less: or ■ Current time and temperature M T W TH F SA SU SET TEMP HOLD TEMP 8 9 : 1 5 6 8 c AM PM HEAT COOL 1 2 3 4 FILTER LO BAT ■ 70 indicates the current setting of the thermostat is 70°F. 68 showsthe present room temperature as68°F....
Page 26 - Temporary Manual Override; Program number flashes.
Programming ■ Press arrow to display currentset and room temperatures. M T W TH F SA SU 8 9 : 6 8 6 0 c AMPM HEAT COOL 1 2 3 4 FILTER LO BAT M T W TH F SA SU SET TEMP HOLD TEMP 8 9 : 7 0 6 0 c AMPM HEAT COOL 1 2 3 4 FILTER LO BAT Temporary Manual Override In the following example, the present room t...
Page 27 - To return immediately to the; Permanent Manual Override; To Return To Program*
In the event you wish to hold your manualoverride for vacation or an extended period of time, follow the temporary manualoverride instructions on page 26, then immediately press HOLD/CLEAR. This will maintain overridesetting indefinitely. “HOLD” willappear on the display. ■ To return immediately to ...
Page 28 - Operations; Filter Monitor; F i l t e r i n d i c a t o r d i s a p p e a r s .
Operations 7 2 . 7 I . 7 0 . Filter Monitor To Reset the Filter Counter to Zero ■ F i l t e r i n d i c a t o r d i s a p p e a r s . M T W TH F SA SU SET TEMP HOLD TEMP 8 6 : 3 0 6 8 c AM PM HEAT COOL 1 2 3 4 FILTER LO BAT M T W TH F SA SU SET TEMP HOLD TEMP 8 6 : 3 0 6 8 c AM PM HEAT COOL 1 2 3 4 ...
Page 29 - Other Features; Temperature Span
Other Features Your thermostat is preprogrammed at thefactory to cycle when the temperature rises1° above or 1° below the temperature settingto provide maximum comfort. It cannot bechanged. Temperature Span
Page 30 - Troubleshooting; Problem; NO DISPLAY; and hold in for two seconds.
Troubleshooting Problem Solution SCRAMBLED OR DOUBLE DISPLAY(numbers over numbers) NO DISPLAY ENTIRE DISPLAY DIMS PROGRAM DOES NOT CHANGE AT YOURDESIRED SETTING AUTO/FAN DOES NOT COME ON 1. Remove clear mylar sticker. 1. Check battery connections and batteries.2. Press reset button once with a small...
Page 31 - ERRATIC DISPLAY
Problem (Continued) Solution (Continued) If you experience any other problems, call 1-901-745-9222 from 8AM to 5PM CentralStandard time for technical assistance. 1. Check that function switch is in correct position (“HEAT” or “COOL”). 2. There may be as much as 20 seconds delay in the thermostat tur...
Page 32 - Wiring Diagrams; THERMOSTAT
Wiring Diagrams 32 4-wire Heat/Cool System 5-wire Heat/Cool System THERMOSTAT G W Y RH RC Heat Relayor Valve Heat/CoolTransformer FanRelay CoolContactor Jumper THERMOSTAT G W Y RH RC Heat Relayor Valve HeatTransformer FanRelay CoolContactor CoolTransformer
