Hunter 44017-01 - Manual - manualsarea.com

Page 2 - Our Technical Support Group is available from 8 am to 5 pm

2 Our Technical Support Group is available from 8 am to 5 pm CST. They may be reached toll-free at 1-888-830-1326.

Page 3 - Table of Contents

3 Table of Contents Important Information ....................................... 5Tools ................................................................. 6 Uninstalling the Existing Unit ............................ 9 Installing the Thermostat ................................ 12Installing the wall ...

Page 6 - TOOlS

6 This thermostat includes two #8 slotted screws and two wall anchors for mounting. To install your new thermostat, you will need the following supplies: Flat-head screwdriver ...................................................................................... Small Phillips-head screwdriver ........

Page 9 - (Some thermostats may have multiple covers, screws; UnInSTAllInG THE ExISTInG UnIT

9 1. Turn the system power OFF from the existing thermostat. Turn the power to the HVAC system OFF at the main power panel or at the furnace. 2. remove the existing thermostat cover to access the wires from the wall. (Some thermostats may have multiple covers, screws or other locking devices that mu...

Page 11 - (If the terminals are not labeled, contact a; proper identification.; *If a wire marked C is present, C may be a

11 4. Using the provided stickers, label each wire according to the chart. (If the terminals are not labeled, contact a qualified HVAC technician.) note: Wire colors do not always comply with standards, so wire color should be ignored. refer to the existing terminal designation for proper identifica...

Page 12 - InSTAllInG THE THErMOSTAT

12 InSTAllInG THE THErMOSTAT InSTAllInG THE THErMOSTAT 1. remove the new thermostat from the back plate by pulling the two halves apart. Thermostat Wall Plate

Page 14 - are flush with the wall.; InSTAllInG THE WAll PlATE

14 2. Position the new wall plate on the wall and pull the labeled wires through the opening. 3. If the existing holes do not match those on the Hunter wall plate, or if there are no existing holes, level the wall plate and mark the wall for two holes. 4. remove the wall plate and drill two 3/16” ho...

Page 18 - HG

18 ATTACHInG THE THErMOSTAT 4. locate the HE/HG switcH on the back of the thermostat. Set the switch to HG for a gas furnace or oil burner. Set the switch to HE for electric furnaces. (The switch has no effect when the system is set to cooling mode.) 5. Insert two fresh AA alkaline batteries. 6. Ali...

Page 21 - OPErATIOn; , The fan will be turned on along with normal

21 OPErATIOn 1. Set the s Et t EmpEraturE slidEr to the desired temperature. 2. The s ystEm s witcH determines the operating mode of the thermostat. Select c ool , o ff , or H Eat . 3. The f an s witcH should normally be located in the a uto position. To run the fan continuously, slide the f an s wi...

Page 22 - InDICATOrS AnD ADUSTMEnT; battery conditions. The first warning is the

22 InDICATOrS AnD ADUSTMEnT 1. The t HErmomEtEr indicates the room temperature. 2. The B attEry i ndicator displays two stages of battery conditions. The first warning is the w Eak B attEry w arninG , indicated by the B attEry i ndicator flashing once approximately every second. When this warning ap...

Page 23 - Span Adjust; SPAN

Page 24 - F. The Span setting remains; Temperature. For maximum system efficiency and; left or right

24 InDICATOrS AnD ADjUSTMEnTS, COnT. 1. remove the top cover from the thermostat. 2. To make your system run lOnGEr, turn the s pan a djust clockwise. 3. To make your system run SHOrTEr, turn the s pan a djust counter clockwise. 4. reattach the top cover to the thermostat. note: The Span range is 0....

Page 25 - My heating or cooling will not turn on or off.; My system continues to operate when the

25 1. My heating or cooling will not turn on or off. 1 a. Check the HE/HG switch to ensure it is set to the correct position. 1 b. Wait. There may be as much as a 4-minute delay before the system turns on or off to protect the compressor. 1 c. Check the circuit breakers and switches to ensure there ...

Page 26 - Sure. Our Technical Support Group is available from 8 am; TrOUBlESHOOTInG

26 Is there help on the web? Yes. Visit http://www.hunterfan.com for more information. .................................................................................... ......... Can’t I just call someone? Sure. Our Technical Support Group is available from 8 am to 5 pm CST. They may be reached t...

Page 27 - Rh; Rc

27 G Rh W Y Fan Relay Heat/Cool 24V Supply Cool Contactor Heat Relay or Valve 4-w ire Heat/Cool System G Rc Rh Fan Relay Heat 24V Supply W Heat Rela y or V alve Y Cool Contact or 5-wire H eat/C ool Sy stem Cool 24V Supply

Page 28 - WIrInG DIAGrAMS; -w ire Heat O nly System

28 WIrInG DIAGrAMS Rh W Heat 24V or M illivolt Supply Heat Relay orValve 2-w ire Heat O nly System G Rh W Heat 24V Supply Heat Relay orValve 3-w ire Heat O nly System Fan Relay

Page 29 - G Rc

29 G Rc Y Cool Contacter Cool 24V Supply 3-w ire Cool O nly System Fan Relay WIrInG DIAGrAMS, COnT.