Hunter 43042-01 - Manual - manualsarea.com

Page 2 - prEVEnTaTiVE MainTEnanCE; DisConnECT ELECTriC; W a r n i n G; CooKinG arEa; C a U T i o n

43042-01 02/21/2008 2 To rEDUCE THE risK oF FirE, ELECTriC sHoCK, or inJUrY To pErsons, oBsErVE THE FoLLoWinG: prEVEnTaTiVE MainTEnanCE a clean fan provides better service. Disconnect the power supply and clean the fan as listed below. To CLEan GriLLE: Use a mild detergent, such as dishwashing liqui...

Page 4 - Before installation

43042-01 02/21/2008 4 remove the motor/blower from the housing. remove the pre-loaded screw tip covers. Back out the pre-loaded screw tips until flush with the side of the housing. remove packing material. Turn off the power source. Before installation Loosen screws. noTE: remove all packing materia...

Page 5 - Choose Installation Option; For new Construction - attaching to joist fo to step a11, page 6

43042-01 02/21/2008 5 7 G pop out the first wiring access slug. Use second if needed. insert the strain relief into the housing and secure with the washer. remove the wiring cover screw. remove the wiring cover. Choose Installation Option For new Construction - attaching to joist fo to step a11, pag...

Page 6 - new Construction – attaching to joist

43042-01 02/21/2008 6 5/81/2 A11 A13 A12 E Connect wires as shown. pull wires through the strain relief. position the correct depth mark at the bottom edge of the joist based on the thickness of your sheetrock. new Construction – attaching to joist screw pre-loaded screws into joist or framing. A14 ...

Page 8 - new Construction – suspended between joists; Go to step; on

43042-01 02/21/2008 8 5/81/2 5/81/2 1/8" Bit slide the mounting rails into brackets. Mark position of screws by using holes as a template. new Construction – suspended between joists position the correct depth mark at the bottom edge of the joist based on the thickness of your sheetrock. Drill a...

Page 11 - Existing Construction – accessible from above; OR; EXisTinG Fan

43042-01 02/21/2008 11 8” 8.5 ” B26 C11 C12 B27 E1 Go to step on page 18 to attach grille. Existing Construction – accessible from above OR remove an existing fan and check to make sure the opening is large enough to accommodate the new motor housing (8”x 8.5”). Cut out an opening for the housing. U...

Page 15 - Existing Construction – accessible only from below

43042-01 02/21/2008 15 2 1 Existing Construction – accessible only from below pull wires through strain relief . remove an existing fan and check to make sure the opening is large enough to accommodate the new motor housing (8”x 8.5”). Move the housing into position above the ceiling. attach existin...

Page 20 - Trouble shooting

43042-01 02/21/2008 20 Trouble shooting problem: Fan does not come on. solution: • Hunter Fan Bath Ventilators are extremely quiet. To confirm that the fan is running, place your hand near the vents to feel the air movement. • Turn power on, replace fuse, or reset breaker. • Check all plug connectio...

Page 21 - Warranty

43042-01 02/21/2008 21 Warranty © 2008 Hunter Fan Company Hunter Fan Company Bath Exhaust Fan LiMiTED WarranTY Hunter Fan Company makes the following limited warranty to the original user or consumer purchaser of this Hunter bath exhaust fan: If any part of your Hunter bath exhaust fan (except for g...

Hunter 43042-01 - Manual

Table of Contents:

Summary

Other Hunter Models