Hunter 28982 - Manual

41490-01 12/01/2005

INSTALLATION INSTRUC TIONS FOR HUNTER

C EILING FAN LIG HT K ITS M ODELS:

28343, 28344, 28345, 28405, 28406, 28407, 28408, 28982, 28983, 28984, 28985, 28986, 28987

28330, 28331, 28332, 28333, 28334, 28335, 28336, 28337, 28338, 28339, 28340, 28341, 28342

W A RNING

• To avoid possible electrical shock , bef ore in-

sta lling light f ixtures, disconnect pow er by
tur ning of f the circuit break ers both to the
outlet box and to its associated w all sw itch
location. If you cannot lock the circuit break-
e r s i n t h e o f f p o s i t i o n , s e c u r e l y f a s t e n a
prominent w arning device, such as a tag, to
the service panel.

• C onnect house w iring to the f an bef ore at-

taching the light f ixture to the f an.

• A ll w iring must be in a ccorda nce w ith na -

tiona l a nd loca l electrica l codes a nd A N SI/
NFPA 7 0 . If you are unf amiliar w ith w iring,
you should use a qualif ied electrician.

C A U TIO NS

• Read entire text carefully before beginning in-

stallation and save these instructions.

• To reduce the risk of electrical shock , install

this light kit only on listed Hunter ceiling fan
models: C ote D’ A zur , C ustom Home 2 ,
C aptiva

,

44” Dominion , Designer’s C hoice

,

O RBit

,

5 2 ” Dominion , M arseille , Santa

Barbara

,

Belle M eade

&

Etruscan

STEP 1: REM OVING W IRING HARNESS

Before you can install the modular accessory light
kit, you must remove the wiring harness and its com-
ponents from the modular switch housing on the
fans listed above. You must then install the wiring
harness into the modular accessory light kit.
NOTE: Refer to Figure 1 for the steps listed below.
1. Locate the reversing switch and carefully remove

the two screws holding the reversing switch to
the switch housing. The reversing switch can now
be removed from the switch housing.

2. Remove the patented breakaway connector from

the fan pull chain.

3. C arefully loosen the bellmouth nut from the fan

pull chain and remove the fan pull chain switch
from the switch housing.

4. Locate and carefully remove the two capacitors

from the switch housing.

5 . You have now disconnected the wiring harness

and its components from the switch housing and
are ready to install them into the modular acces-
sory light kit.

STEP 2: INSTA LLING W IRING HA RNESS

NOTE: Refer to Figure 1 for steps listed below.
1. Locate the two wires in the lower switch housing

labeled “ C onnect Light Here” or “ For Light Use” .
One will be white, the other black/white. Unscrew
the wire nuts counterclockwise to expose the bare
metal leads.

2. Locate the white wire and the black wire coming

from the light fixture.
C onnect the black wire from the light fixture to
the black/white wire from the lower switch hous-
ing.
C onnect the white wire from the light fixture to
the white wire from the lower switch housing.
To fasten the wires, twist the two bare leads to-
gether. Place a wire nut over the intertwined length
of wire and twist clockwise until tight.

Fa n Spe e d
Sw it ch

Ca pa cit o r

R e ve r se Sw it ch

M u lt i-w ir e Plu g
Co n n e ct io n

Ca pa cit o r

B e llm o u t h N u t

M 3 H o u sin g
A sse m bly Scr e w s

Ligh t K it Le a d W ir e s
a n d W ir e N u t s

FIGURE 1