Hunter 28393 - Manual

Hunter 28393 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

Page 2 – STEP 2: Wiring the Fixture - Ceiling Light; NOTE: Refer to Figures 2 and 3 for the steps below.; CAUTION; NOTE: Refer to Figure 3 for the steps below.; STEP 4: Final Assembly; NOTE: Refer to Figures 3 and 4 for the steps below.; FIGURE 3
Page 3 – WARNING; CAUTIONS; NOTE: Refer to Figure 3 for the steps below .; STEP 2: W iring the Light Kit - Ceiling Fan; al
Page 4 – STEP 3: Mounting the Light Kit - Ceiling Fan; locate and install; Warning: Failure to ensure that all fasteners are; Install two 60 watt maximum type A-19 bulbs into the; STEP 4: Light Kit Final Assembly - Ceiling Fan; NOTE: Refer to Figures 5 and 6 for the steps below .; If you have any problems or questions please contact us via; FIGURE 6

Loading the manual

41695-01 5/17/2004

INSTALLATION INSTRUCTIONS FOR HUNTER

DUAL MOUNT LIGHT FIXTURES

MODEL 28393, 28394

NOTE:

This is a Dual Purpose Light kit that allows the user to install the light fixture to the ceiling, as you would any

light fixture. It also has the feature of being convertible to mount directly to a Hunter ceiling fan. Please follow the

directions below that pertain to the type of installation this light fixture will be installed in.

IMPORTANT NOTE: READ AND SAVE THESE INSTRUCTIONS!

WARNING

• To avoid possible electrical shock, before in-

stalling light fixtures, disconnect power by

turning off the circuit breakers both to the

outlet box and to its associated wall switch

location. If you cannot lock the circuit break-

ers in the off position, securely fasten a

prominent warning device, such as a tag, to

the service panel.

• This fixture must be mounted to an approved

outlet box that is directly supported by the

building structure.

• All wiring must be in accordance with na-

tional and local electrical codes and ANSI/

NFPA 70. If you are unfamiliar with wiring,

you should use a qualified electrician.

CAUTIONS

• Read entire text carefully before beginning

installation and save these instructions.

• Should you desire to change the unit over to

a different style mounting, you will need to

follow these instructions to convert from one

installation style to another.

CEILING LIGHT FIXTURE
SECTION:

STEP 1: Site Pr eparation - Ceiling Light

If you are replacing an existing light fixture,

disconnect and remove the old fixture and mounting

bracket, leaving the wires exposed coming from the

outlet box.

Locate and thread the two 8-32” screws, sup-

plied in the sack parts, into the hanger bracket threaded

holes as shown in Figure 1.

Locate and install the two 8-32” nuts on the 8-

32” screws and tighten until snug against the hanger

bracket.

Using the two screws supplied with the outlet

box, mount the hanger bracket to the outlet box, as

shown in Figure 2.

Warning: Failure to ensure that all fasteners

are secure could result in the fixture falling.

8-32” SCREWS

H A N G E R
B R A C K E T

8-32”
N U T S

TOWARDS
E L E C T R I C A L
BOX

FIGURE 1

H A N G E R
B R A C K E T

HOUSE
S U P P LY
LEADWIRES

E L E C T R I C A L
BOX

S U P P LY
GROUND
W I R E

GROUND
S C R E W

E L E C T R I C A L
BOX
MOUNTING
S C R E W S

L I G H T
F I X T U R E
GROUND
W I R E

FIGURE 2

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - STEP 2: Wiring the Fixture - Ceiling Light; NOTE: Refer to Figures 2 and 3 for the steps below.; CAUTION; NOTE: Refer to Figure 3 for the steps below.; STEP 4: Final Assembly; NOTE: Refer to Figures 3 and 4 for the steps below.; FIGURE 3

41643-01 07/11/2003 STEP 2: Wiring the Fixture - Ceiling Light NOTE: Refer to Figures 2 and 3 for the steps below. 1. Locate the green ground wire from the light fixture and the supply ground wire coming out of theelectrical box.2. Connect both ground wires underneath the green ground screw on the h...

Page 3 - WARNING; CAUTIONS; NOTE: Refer to Figure 3 for the steps below .; STEP 2: W iring the Light Kit - Ceiling Fan; al

41695-01 5/17/2004 WARNING • To avoid possible electrical shock, before in- stalling light fixtures, disconnect power by turning off the circuit breakers both to the outlet box and to its associated wall switch location. If you cannot lock the circuit break- ers in the off position, securely fasten ...

Page 4 - STEP 3: Mounting the Light Kit - Ceiling Fan; locate and install; Warning: Failure to ensure that all fasteners are; Install two 60 watt maximum type A-19 bulbs into the; STEP 4: Light Kit Final Assembly - Ceiling Fan; NOTE: Refer to Figures 5 and 6 for the steps below .; If you have any problems or questions please contact us via; FIGURE 6

41695-01 5/17/2004 STEP 3: Mounting the Light Kit - Ceiling Fan IMPORT ANT INST ALLA TION INFORMA TION: Beforemounting the light kit to your ceiling fan, locate and install the lockwashers included in the light kit sack parts onto the screws identified below in Sub-step 2. 1. Align the holes in the ...