Hunter 24756 - Manual

Connect the blue neutral wire to the terminal marked “N.”

Connect the brown line wire to the terminal marked “L.”

Note:

An additional “L” terminal is provided for separate control of the light fixture. This terminal is not

required for controlling the light fixture with the remote control.

Note

: If there is no separate line for the light kit, connect the black/white wire and the brown wire from

the motor housing to the same “L” terminal.

Feed the electrical connector from the fan through the hole in the hanger bracket so it is on the outside

of the hanger bracket.

The remote receiver is connected between the electrical connector coming from the fan and the electrical

connector coming from the hanger bracket terminal block. See Figure 2.

Slide the remote receiver through the two rectangular openings in the hanger bracket and center it in

the hanger bracket, as shown in Figure 4.

The male connector on the remote receiver attaches to the female connector on the fan. The female

connector on the remote receiver attaches to the male connector on the hanger bracket. They are

keyed so they will only connect one way. See Figure 2.

Do not force the connectors. To aid in proper connection, align the color code stickers on each connector

so they are in line with each other then press them together until they lock.

CautioN:

Be sure no bare wire or wire strands are visible after making connections.

Make sure none of the wires are caught in any of the hanging assembly components. the white

antenna wire should be extended to its full length and positioned between the hanger bracket

and the canopy parts upon final assembly.

Once the receiver is installed, continue with the appropriate instructions from the fan installation manual

to finish installing the fan.

Testing the Control

Warning!

-

Do not use the light fixture pull chain to operate the light while power is

applied to the receiver as damage could occur to the receiver. it is recommended to shorten the

pull chain(s) to prevent accidental use.

• Do not use the fan pull chain switch to operate the fan speeds while power is applied to the

receiver as damage could occur to the receiver.

Remote Ceiling Fan & Light Control

Transmitter Model: 24756
Part Number: 87261-01
Transmitter Battery: 12V, Type A23, MN-21 or equivalent
Receiver Part Number: 87262-01
Ratings: 240 VAC, 50/60Hz, 1.0 Amp Fan
Receiver Weight: 160g
Max 300 Watts Incandescent or Halogen Light

Read and Save these Instructions

WaRNiNG! Risk of Electrical Shock

• to avoid possible electrical shock, before wiring fan, disconnect power by turning off the power

mains both to the outlet box and to its associated wall switch location.

Compliance

• this equipment has been tested and complies with: EN 300220:2002 and EN 55022:1998 Class

B.

• all wiring must be in accordance with national and local electrical codes. if you are unfamiliar

with wiring, you should use a qualified serviceman.

• In Australia, national laws require a qualified electrician to install this accessory into a ceiling

fan.

• to avoid overheating and possible damage to other equipment, do not install to control

a receptacle, fluorescent light fixture, motor-operated appliance, or transformer-supplied

appliance.

• Use only to control one paddle-blade ceiling fan and incandescent or halogen light fixture.

Note

:

Any changes or modifications to the transmitter or receiver not expressly approved by Hunter

Fan Company may void one’s authority to operate this remote control.

For use only with electrically reversible ceiling fans rated at 1.0 A or less, and fan incandescent light

kits rated at 300 W or less.

If this equipment does cause harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

• Consult the dealer or an experienced radio/TV technician for help.

Installing the Receiver

Disconnect the power mains to the ceiling fan and light kit at the main electric panel. Remove fuse or

move circuit breaker to the OFF position. Turn off wall switch.

IMPORTANT!

Before installing this control, change the factory default jumper / DIP switch settings

to your own unique code. The jumpers are under the battery compartment of the remote and the DIP

switches are on the flat side of the receiver. Refer to Figure 1. Remove the battery from the remote

and turn off power to the fan when making any jumper / DIP switch setting changes.

Figure 1 - Setting Receiver DIP Switches and Remove Jumpers

A jumper that connects the two pins is equivalent to a DIP switch being set to the ON position. A jumper

stored on a single pin is the same as a DIP switch set in the OFF position.

Be sure the jumper settings of the transmitter and receiver match, or the ceiling fan will not function.

Select different combinations of jumoer / DIP switch settings to prevent miss operation due to other

remote control fans, garage door openers, etc.

Note

: The jumpers on the transmitter read from right to left 4-1, and the DIP swiches on the receiver

read from left to right, 1-4. Be sure to match the settings by number rather than by their right to left

positions.

Install one type A23, MN-21 or equivalent, 12 volt alkaline battery inside the hand-held transmitter

after

setting the ON / OFF jumper settings on the remote to match the ON / OFF DIP switch settings on the

receiver. Refer to Figure 1.

Install the ceiling fan according to its instructions, up to the point of making the electrical connections.

Connecting Fan to Electrical Source

Use Figures 2 and 3, for reference in making the following electrical connections.

Connect the supply mains to the terminal block mounted on the hanger bracket.

Connect the safety earth (green/yellow) wire to the terminal marked

.

When the installation is complete and while there is no power (your wall switch is in the OFF position)

to the receiver, pull the light kit’s pull chain once and pull the fan speed pull chain once.

Turn on the wall switch. The light kit should turn ON. If the light remains OFF, turn off the power at the

wall switch. Pull the light kit’s pull chain to turn the light ON.

Turn the wall switch back ON.

Press the remote control’s fan speed button. The fan should start and reach it’s maximum speed. If the

fan does not start or is turning too slow, turn off the power at the wall switch. Pull the fan’s pull chain to

change speed. Reapply power and try HIGH.

Hunter Fan Company

2500 Frisco Avenue

Memphis TN 38114 USA

© 2006 Hunter Fan Company

41612-01 10/12/06

Hunter Fan

Company

Figure 3 - Terminal Block Connections

Possible Causes

Main Power not restored.

Fan pull chain not set to HIGH.

Light pull chain not set to ON.

Receiver wiring incorrect.

Tr a n s m i t t e r a n d r e c e i v e r D I P

switches do not match.

Battery too weak.

Signal blocked from reaching

receiver.

Solution

2. Operates only at

close range.

Symptom

3. Inconsistent operation.

Replace fuse. Turn ON supply mains.

Turn ON wall switch.

Turn OFF power at wall switch or

main supply mains. Set fan to HIGH

speed.

Set light kit to ON.

Verify wiring connections.

Set transmitter and receiver to same

DIP switch setting.

Replace with new, alkaline battery.

Extend antenna into wire into ceiling

box, or move it for better reception.

1. No functions operate.

Battery too weak.

S i g n a l p a r t i a l l y b l o c k e d f r o m

reaching receiver.

RF interference.

Continuing RF interference.

Replace with new, alkaline battery.

Extend antenna into ceiling box, or

move it for better reception.

Turn OFF wall switch for 5 seconds,

then turn back ON.

Change dip switch settings to a

different code in both Transmitter

and Receiver.

Troubleshooting

Figure 2 - Wiring Diagram

Remote

Receiver

Hanger

Bracket

Figure 4 - Remote Receiver in Hanger Bracket

Operation

Turn ON the wall switch, the light will turn ON at maximum brightness and the fan will be off.

Light Operation

• ON and OFF: Press and quickly release the light button on the

hand-held remote to turn the light OFF and ON. See Figure 5 for

remote button locations.

Dimmer

Press and hold the light button for more than one second to dim or brighten

the light. If brightness is initially at 100%, then the brightness will decrease

to 95% and so forth by 5% increments as long as the light button is pressed.

When the minimum brightness of 25% is reached, the setting will pause

and then begin to increase by 5% increments as long as the light button

is pressed. See Figure 6.

Fan Operation

• ON, OFF, and Speed Setting: Press the fan button to turn on the ceiling fan

at HIGH speed. Press again to change the speed to MEDIUM, then again

to LOW, and then again to turn the fan OFF. See Figure 7.

To reverse the fan direction, turn the fan off and wait for the blades to stop

moving. Switch the reversing switch on the fan to the opposite direction.

Restart fan.

Low Battery Detection

• The low-battery icon will flash when the battery needs to be changed. If

there is a low battery, it will also flah during standby mode.

• Replace the battery when the low-battery warning begins to flash as

shown in Figure 8.

Standby Mode

• To save battery power, if no button on the remote is pressed for one

minute, the remote LCD will go into standby mode.

• During standby mode, all LCD icons are turned off.

• The LCD will will resume original display when any button is pressed.

The button function is not performed but acts as a wake up key.

Receiver

Remote

DIP Switches

Jumpers

Battery Compartment

Figure 6

Figure 8

Figure 7

LCD Display

Light

Fan

Figure 5